Loader

JCB 403 Plus / Neufahrzeug / 2025 / Gabel / Schaufel

Condition: new, Year of construction: 2026, _____Standard Equipment / Technical Data Engine Rated Power (ISO) 68 / 90 kW / hp at 2200 rpm Max. Power 71 / 95 kW / hp at 2000 rpm Max. Torque 405 Nm at 1500 rpm Manufacturer / Type: Agco Power / AP 44MBTN-D5 Low-emission engine, 4 cylinders / 4.4l, 4V, STAGE 5 Controlled Turbocharger, SCR - Catalyst DOC - Diesel Oxidation Catalyst SCR Particulate Filter Catalyst Hood - single-piece, foldable Exhaust pipe on the right side in front of the cab Fuel tank capacity 198 liters / AdBlue 18 liters Transmission / PTO 16/16-speed Dyna-4, SpeedMatching, 40 km/h PowerControl operation on the left with load-sensing reversing gearbox, clutch operation, 4-stage load shifting with 1 lever, T-shuttle lever in the side console Partially automatic group shifting and Autotronic monitoring Permanently cooled wet disc clutches with independent lubrication system PTO: 540 / 540E / 1000, stub shaft 1 3/8", 6-spline Electrical engagement in the cab PTO START/STOP button on the rear, left fender Hydraulics / Lifting System Open Center system Quick coupler Cat. 2 Upper link control 4,300 daN maximum lifting force, 2 external lifting cylinders Adjustable lifting struts on both sides EHR with external control on both fenders Quick adjustable automatic drawbar coupling Electrical system Thermostart, 120 A alternator Power supply (12 Volt) for external devices with connector Axles / Additional Weights All-wheel drive front axle with switchable differential lock Rear axle ND with flange hub Oil-cooled disc brakes Front fender, width adjusted, rotatable Rear fender width 1.80 m, without extensions Front weight carrier with integrated drawbar and drawbar pin Driver's Seat Vibration-damped standard cab with standard roof, ventilation and heating Integrated safety frame with tinted glazing Doors on both sides with safety steps Tsdpfezpcvdsx Aahjc Steering column adjustable in height and inclination Air-suspended driver's seat with armrests, swivel adapter, safety belt Exterior & wide-angle mirrors Interior mirror Analog-digital instrument panel (SIS) Radio preparation with antenna and speakers 4 work lights front and rear on the cab roof 2 driving lights in the hood and on the handrails, 2 work lights on the rear fenders Special Equipment: Fuel tank protection PowerControl & Brake on Neutral (clutch effect) 100 l/min, Open Center hydraulic system oil flow coupling (58+42 l/min) Front loader quick coupling system Leak oil collector on quick couplers 3 control valves: 1x MR, dw, EA, SST + 1x dw, NL, SST + 1x dw, NL, SST + free return 2.5t front lift, 1 hydraulic line set, electrical socket MF front loader preparation: foundation set, hydraulic set, electrical control via joystick, PTO: 540/540E, flanged, 6-spline, internal engagement Rear fender extensions - 100mm Tires 480/70R38 & 380/70R28 Air conditioning Cab with mechanical suspension Telescopic exterior & wide-angle mirrors Passenger seat with belt Air-suspended driver's seat, automatic adjustment with safety belt, swivel adapter and armrests Rear window wiper / washer system Without MF Connect (MF Telemetry System)

Condition: excellent (used), functionality: fully functional, maximum load weight: 3,500 kg, lifting height: 14,000 mm, Year of construction: 2007, operating hours: 5,700 h, TELEHANDLER Manitou MT 1435 HSL Turbo Year 2007 Tedpfx Aeyy R Npjahjc Lifting height 14 meters Capacity 3.500 kg Working hours 5700 Diesel engine Forks Regular documentation

Condition: good (used), functionality: fully functional, operating hours: 90 h, power: 29.42 kW (40.00 HP), motor manufacturer: Lombardini, overall weight: 2,100 kg, Goldoni Euro 45SN articulated tractor with only 90 working hours on the clock. The rotary tiller is available as an option; it is lightly used but in excellent condition. Brand: Goldoni Model: Euro 45SN Drive: Diesel, 4-cylinder Weight: 2100 kg Operating hours: 90 hours Engine: Lombardini 40 hp Todpfx Aaoy Sad Tehec Price without tiller: €23,500 Price with tiller: €26,000

Condition: used, Year of construction: 2020, operating hours: 521 h, Internal vehicle number: VTC30048 Available immediately. More information at: Luis Lucena Viktoria Sologubova Manitou MHT 10180 heavy-duty telehandler – 18-tonne lifting capacity – 521 operating hours High-performance Manitou MHT 10180 heavy-duty telehandler, manufactured in 2020, with just 521 operating hours. The machine offers a maximum lifting capacity of 18,000 kg, a lifting height of 9.63 m, and is equipped with a hydraulically adjustable fork carriage and pallet forks. Technical data: * Vehicle number: VTC30048 * Vehicle condition: Used machine * Category: Telehandler * Manufacturer: Manitou * Model: MHT 10180 * Series: 129M ST4 S1 * Year of manufacture: 01/2020 * Model year: 2020 * Operating hours: 521 hours * Maximum lifting capacity: 18,000 kg * Maximum lifting height: 9.63 m * Maximum reach: 5.56 m * Unladen weight with standard forks: 24,000 kg * Technical inspection: New * CE marking: Present Engine and drive: * Engine manufacturer: Mercedes-Benz * Engine type: OM 934 LA * Emission stage: Stage IV/Tier 4 Final * Cylinders: 4 * Displacement: 5,100 cm³ * Power: 129 kW (176 hp) * Maximum torque: 750 Nm at 1,600 rpm * Transmission: Hydrostatic * Forward/reverse gears: 2/2 * Maximum travel speed: 25 km/h * Traction force under load: 15,970 daN * All-wheel drive * All-wheel steering * Automatic negative parking brake * Hydraulic service brake Hydraulic system: * Variable hydraulic pump * Hydraulic flow rate: 205 l/min * Hydraulic pressure: 350 bar * Hydraulic oil tank: 290 liters * Hydraulically adjustable fork carriage Dimensions: * Overall length with implement carriage: 6.65 m * Overall width: 2.52 m * Overall height: 3.00 m * Wheelbase: 3.75 m * Ground clearance: 0.44 m * Turning radius (outer radius): approx. 5.50 m * Tilt angle: 12° * Dump angle: 105° Capacities: * Fuel tank: 315 liters * AdBlue tank: 63 liters * Hydraulic oil: 290 liters * Engine oil: 21 liters Cab and safety: Enclosed ROPS/FOPS cab, Level 2 Safety system according to EN 15000 JSM joystick control All-wheel steering Rotating beacon Work lights Cab protection grille Large-dimensioned off-road tires Noise level at the driver's seat: 80 dB(A) External noise level: 107 dB(A) Attachment: * Manufacturer: Manitou * Type: PFF + POS + DL * Serial number: 53010702 * Year of manufacture: 2019 * Self-weight: 1,900 kg * Rated lifting capacity: 14,000 kg * Load center: 1,200 mm * Hydraulically adjustable fork carriage Tjdpjza Nq Rsfx Aahoc * Pallet forks included Inspection and functional test possible by prior arrangement. Further information, photos, load charts, and videos are available upon request. Errors, changes, and prior sale reserved.

Condition: excellent (used), overall weight: 6,500 kg, Year of construction: 2015, operating hours: 4,500 h, Equipment: pallet forks, CAT 906 Tjdpfx Aeztb R Ieahsc 2015 4500 hours Bucket and forks included.

Condition: used, Volvo Wheel Loader L120G Todey Dt Aajpfx Aahsc Year: 2013 Hours: 36595

Condition: excellent (used), Year of construction: 2015, I sell the 2-head UV-drying tunnel Superfici Essiccatoio UV Model: Poliedra S.Cure 1650x2 + TT1 3500. Todsffk Etepfx Aahjc Year 2015. Available immediately. Repairs needed: Display, Energy power units for each two UV-units

Condition: used, functionality: fully functional, fuel type: diesel, Year of construction: 2023, operating hours: 181 h, construction height: 2,310 mm, drive type: Diesel, load capacity: 2,190 kg, construction width: 1,230 mm, Farm loader Mast type: None Technical condition: very good Front tires type: pneumatic Front tires condition: 80 - 100% Rear tires type: pneumatic Todjvgiazspfx Aahoc Rear tires condition: 80 - 100% Rear work lights, front work lights, heating, soot filter, full cabin, CE certificate, safety light, Image serves as a symbol for quick coupler pump type: gear pump hydraulic flow rate - hydraulic pressure: 58.3 l/210 bar system pressure drive: 420 bar

Condition: new, saw blade diameter 355 mm capacity 90 degrees: round 115 mm capacity 90 degrees: square 120 x 106 mm capacity 90 degrees: flat 102 x 197 mm 25,4 mm connected load frequency 230 V total power requirement 2,3 kW weight of the machine ca. 28 Kg Dimensions (LxWxH) 0,6 x 0,35 x 0,45 m Machine for cutting pipes and profiles made of steel, light metal, Plastic, non-ferrous metal and composite materials. Tjdpfxjupw Tke Aahoc

Condition: refurbished (used), functionality: fully functional, year of last overhaul: 2025, 1) Log Yard with 10 Boxes (Drop Boxes) – New and Used Log Feed and Sorting Line New Feed rate 50 m/min. as well as the following used components: Comprising: New cross feed conveyor, step feeder Used log transfer carriage, Used log transfer carriage with ejector, Used Cambio 50 debarker, Used split detection unit with belt, Measuring section, sorting log carriage. Including debarking; Inspection and Painting; including log infeed. Without boxes, sheet metal cladding, measuring system, discharge control, or control cabinet. Root reduction. 2) Log Infeed for Canter Line Heavy-duty cross log conveyor NEW Cross log conveyor in 4-strand execution Axle spacing: 7.5 m Total length: 8.0 m Drive shaft: 100 mm diameter Chain: Bush conveyor chain, pitch 100 mm – heaviest version Fixed rear stops, without sheet metal cladding Steel substructure: HEB 200 Construction height: 1000 mm Drive: geared motor 7.5 kW 3) Equalizer NEW Number of chains: 4 Axle spacing [mm]: 3500 Overall width [mm]: 5730 Paddle spacing [mm]: 1000 Drive shaft diameter [mm]: 100 Drive SEW [kW]: 7.5 Speed [m/min]: 10 Design: completely sheet metal covered between chain runs 4) Step Feeder NEW Feed steps: 4 Overall width [mm]: 4200 Plate thicknesses [mm]: moving steps 12 mm, fixed steps 20 mm Drive SEW [kW]: 18.5 Drive via crank mechanism and geared motor 5) Canter Line (WD brand) Log transfer carriage before RB 2 infeed Length extension to 18.5 m – drive and deflection RB 2 infeed with powered steel chain bed, designed for lateral log infeed. Conveyor chain with carrier dogs, frame in welded construction. Intake and centering unit ZE with log rotation unit TDV and centering device. Feeding unit ZE Log length: 2.5 – 5 m Clear width: min. 80 mm Clear width max.: 780 mm Construction height: 1000 mm Weight: 5400 kg Profile canter FZ 3 Machine frame with base frame 2 knife head housings with main shaft bearing, 2 knife heads with finishing segments, Drive power 90 kW Log diameter: min. 100 mm, max. 400 mm Chipping height above the chain max. 515 mm Distance between disks max. 570 mm Distance between disks min. 60 mm Disk diameter: 1260 mm Positioning via electric motors 2 hydraulic units 35 kW hydraulic pre- and post-cut Pre-cut square timber turning device Tedpfx Aaoykr Aqehsc Electrically powered roller conveyor TR 800 Centering and feeding unit ZE with FZ 3 canter