1998 Kaltenbach TL 350

Kaltenbach TL 350

Condition: used, Year of construction: 1999, Kaltenbach TL350 Upcut Mitre Saw, 5m of Infeed Rails, 350mm Blade, 90 Deg of Mitre Adjustment, Manual Blade Operation. S/No. 121051 (1999) Decommissioned. Country of Origin: Germany Gbodpfx Ajy H Ictef Ajl Location: These lots are located in High Wycombe, UK. Unfortunately there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser.

Condition: used, Year of construction: 2023, DOUBLE GLASS BEAD SAW TRF 527 VIS CE 1 pc DOUBLE GLASS BEAD SAW TRF 527 VIS CE TRF 527 VIS: Double miter saw for the simultaneous cutting of two glass beads positioned one above the other. The right saw unit is fixed, adjustment of the left unit is via the set cutting length can be read off a digital display. The units have supports that allow two glass beads to be cut simultaneously. The upper support can be removed for cutting larger cross-sections. After the cutting process is completed, the pneumatic clamping cylinders automatically swing to the side to simplify loading and unloading of the machine. STANDARD EQUIPMENT • Fixed unit on the right • Digital dimension display • Pressure switch • 2 HM-tipped saw blades • Electrical system with motor brake, undervoltage release, motor protection switch • Pressure switch • Tool set • Guards with horizontal clamping devices, pivoting • Two-hand control • Belt drive • Pneumatic unit lift • Middle support TECHNICAL DATA • Motor power 2 x 1.2 kW • Saw blade diameter Ø 220 mm • Max. cutting height without support 80 mm • Max. cutting width at 90 degrees 55 mm • Max. cutting width at 45 degrees 40 mm • Max. cutting length 2800 mm (optional 4000 mm) • Min. cutting length 158 mm • Weight 217 kg • Space requirement (standard equipment) 3000 x 850 mm Extended cutting capacity 1 pc Maximum cutting length • 4000 mm Star stop 4 positions 1 pc set 2 mechanical stops for adjusting up to 4 intermediate angles. Additional center support. 1 adjustment for rebated profiles. 1 adjustment for rebated profiles as per drawing: - Attachment to the clamping devices to compensate for the profile inclination - Allowances on the rear stops of the units and the center support. The sketch below shows (in green) a beveled presser that follows the inclined profile and presses it against the allowance on the stop (shown in red). Storage location: Garbsen Gbodexnlgcjpfx Af Ael

Condition: used, Year of construction: 1990, Kaltenbach TL350 Upcut Mitre Saw with 7 Metre Graduated Guide Infeed, 350mm Blade, 90 deg of Mitre Adjustment, Manual Black Operation. S/No. 113199 (1990) 113200 (1990). Country of Origin: Germany Location: These lots are located in High Wycombe, UK. Unfortunately there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. Gedpjy H H Ibofx Af Aebl

Year of construction: 1994, condition: used, Max. saw blade diameter: 350 mm Manual material tensioner minimum quantity spraying Gbjdpfx Afoud Uvke Ajl Digital angle display

Condition: new, capacity 90 degrees: round 240 mm capacity 90 degrees: square 240 mm 165 x 310 mm saw band length 2725 x 27 x 0,9 mm mm Gedpfxehpktvo Af Aobl table height 890 mm band speed 35 / 70 m/min total power requirement 1,1 kW weight of the machine ca. 0,35 t Dimensions (LxWxH) 1,7 x 0,75 x 1,8 m The Z252/DG has the following equipment: - hydraulic cylinder, - emulsion pump, - eccentric clamp, - base, - saw blade, - 400V plug -16A- The machine is delivered fully assembled and ready for immediate use.

Year of construction: 2004, condition: ready for operation (used), A fully automatic Schüco glazing bead saw is available. Saw blade diameter: 400mm, cutting angle: 45°/90°, motor type: E63SP-2, speed: 2800rpm. On-site inspection is possible. Gsdpjwu Ez Njfx Af Asbl

Condition: used, Column Drilling Machine ALZMETALL Type AB 3 ESV Machine No. 15967 Year of manufacture 1977 Drilling capacity: 32 mm Spindle taper: MT 3 – short quill Distance spindle nose – table: 545 mm (short quill) Distance spindle adapter – table: 395 mm (MT adapter) Throat: 290 mm Quill stroke: 160 mm Table size: Ø 545 mm Column diameter: 220 mm Spindle speed: 55 – 1450 rpm, stepless Gbedpfx Afsharwvj Ajl Motor power: 1 / 1.6 kW Supply voltage: 380 Volt, 50 Hz - Spindle speed via 2 gearbox stages, 2 motor speeds and stepless through variable-speed drive - Intermediate gear stage for high torque at low speeds - MT adapter from MT3 to MT4 - Automatic feed 0.1 – 0.2 – 0.3 mm/rev - Swiveling drill table - Table height adjustment via hand crank - Heavy machine base with machined workpiece support surface (not original Alzmetall) - Work area lighting Space required (L x W x H): 1150 x 650 x 2000 mm Weight: 850 kg Good condition

Condition: new, The SBS 255, part of the Horizontal Mitre Cutting Bandsaws category and the Semi-Auto Bandsaw group, is a compact, robust machine designed for efficient machining of small batches. This universal workshop band saw features a one-piece cast-iron saw frame that is torsion-proof and swivels 60° to the right and 45° to the left, allowing for versatile cutting options. With a rigid vise equipped with lateral slide and long guideways in the movable jaw segments, users can achieve precise cuts on various workpiece sizes, thanks to the combination of carbide jaws and adjustable ball bearing guides. The SBS 255 operates quietly, ensuring short machining times and easy handling, which leads to increased productivity. Additionally, it is powered by a strong motor for continuous operation and comes with a high-capacity coolant system. Included with the saw are essential tools like a saw blade, base, pressure gauge, and operator instructions. KNUTH provides the quality assurance you expect, so order online today to enhance your workshop with the SBS 255 Horizontal Mitre Cutting Bandsaw. Gsdeuyiqdepfx Af Aobl

Condition: excellent (used), Year of construction: 2000, Technical specifications: Max. cutting width: 3050 mm Max. cutting capacity for steel: 0.4 - 6.0 mm Max. cutting capacity for stainless steel: 4.0 mm Max. cutting capacity for aluminium: 8.0 mm Adjustable back gauge: 1050 mm NC control Cutting gap adjustment via control Cutting angle adjustment via control: 0.4 – 2.2° Sheet holding function Strokes per minute: 33 cuts Motor power: 5.5 kW Dimensions (L x W x H): approx. 3800 x 2300 x 1950 mm Weight: approx. 6.5 tons Gbedpoymgrrefx Af Aol The seller accepts no liability for typographical or data transmission errors. The machine’s appearance, technology and wear are consistent with its age; used machines are sold without any warranty.

Condition: used, Cutting length: 3100 mm Steel cutting capacity: 12 mm Gbjdpfxsxuh Ips Af Ajl Backgauge: 1000 mm