Injection Moulding Machine

KraussMaffei KM 160-1000 CX

Condition: excellent (used), Year of construction: 2012, Krauss Maffei KM 160–1000 CX Injection Moulding Machine 🔹 Basic Information Manufacturer: Krauss Maffei Model: KM 160–1000 CX Year of Manufacture: 2012 Operating Hours: 57,654 hours Category: Hydraulic Injection Moulding Machine 🔧 Clamping Unit Clamping Force: 1,600 kN (160 tons) Platen Dimensions: 820 × 845 mm Tie-bar Distance: 520 × 520 mm Minimum Mold Height: 300 mm Maximum Opening Stroke: 950 mm 💉 Injection Unit Screw Diameter: 50 mm Injection Volume: 432 cm³ Shot Weight: 393 g Injection Pressure: 2,304 bar ⚡ Electro-hydraulic System Pump Motor Power: 37 kW Heater Power: 18.7 kW 👉 Option to install Energy Saving System (ESS) – actual energy consumption reduction by up to 30–60% 📐 Dimensions & Weight Machine Weight: 9 tons Nwodeyv E E Depfx Ab Ujl Dimensions (L × W × H): 5.54 × 2.06 × 2.18 m

Condition: like new (used), Year of construction: 2016, Wittmann Battenfeld Eco Power 110/130 Unilog B6P electric (2016) Clamping force: 110 t Screw diameter: 22 mm Shot volume: 41 cm3 Screw L/D ratio: 20 Calculated stroke volume : 41,8 cm3 Correct injection pressure : 2,864 bar Max. screw speed : 500 min Screw tongue : 150 Nm Nozzle path contact force : 250/40 mm/kN Injection flow outside : 76 cm3/s Nwodpfx Aou Eki Ssb Ujl Cylinder heating capacity : 6,3 kW Number of heating zones : 4 Working hours: 35.953 hours Type: Horizontal Drive: Electric

Year of construction: 2018, condition: new, loading capacity: max. 1.000 Kg. Nodpfxedx Ryyj Ab Uewl coil inside diam.: min. 400 mm coil outside diam.: max. 1.100 mm coil hight: max. 800 mm

Condition: ready for operation (used), Year of construction: 2020, operating hours: 8,000 h, clamping force: 500 kN, screw diameter: 25 mm, injection weight: 46 g, total height: 1,779 mm, overall weight: 4,200 kg, This SUMITOMO SHI DEMAG Intelect 2 50/370-110 was manufactured in 2020. It features a fully electric direct-drive system, NC5+ control for enhanced energy efficiency, and precise injection dynamics. Includes a granule dryer, industrial robot, conveyor belt, and temperature units. Ideal for high-quality injection moulding processes. Contact us for more information about this machine. Additional equipment • Granule Dryer • Handling System • Conveyor Belt - 1400 mm x 400 mm • Precision Scale • Temperature Units - 2x HB‑Therm Machine Benefits Technical Machine Benefits • Exceptional energy efficiency • Enhanced platen rigidity and mold safety • Fully electric direct-drive system • Ultra-precise direct-drive motors with 0. 1 ms response time • Displacement: 52 cm³ • Spray pressure: 2180 bar • Tool clamping platens: 520 x 570 mm Extra Information Control Unit Nwsdpfx Abox D Ecco Uel Advanced control system with NC5+ Automatic mold height and clamping force adjustment Energy-saving routines Dimensions Machine Depth 4308 mm

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036721, clamping force: 6,500 kN, screw diameter: 70 mm, clearance between the columns: 1,110 mm, displacement volume: 1,078 cm³, injection pressure: 1,877 bar, injection weight: 981 g, opening stroke: 3,200 mm, plate height: 1,540 mm, drive type: Hydraulisch, clear span: 3,200 mm, tool weight: 22,00,000 g, Injection Moulding Machines Directly from the Manufacturer! As the manufacturer KraussMaffei, we offer you our certified and flexible stock machines: The hydromechanical two-platen clamping unit of the GXW machine sets new standards in terms of quality and productivity. With the sophisticated GuideX sliding shoe, forces are ideally absorbed and the service life of the moulds is extended. The innovative GearX locking system engages instantly and reliably. Powerful, user-friendly and value-retaining. TECHNICAL DATA: KM 650 / 2000 / 2000 GXW G06 (Order 38618339) CONTROL SYSTEM - MC 6 with 24'' TFT color screen with multitouch functions CLAMPING UNIT - Clamping force: 6500 kN - Max. mould opening force: 455 kN - Daylight opening (h x v): 1110 x 960 mm - Platen size (h x v): 1540 x 1440 mm - Mould installation height min. - max.: 1550 mm (without centre platen) - Opening stroke: 3200 mm - Max. mould opening distance: 1650 mm - Max. mould weight: 22,000 kg INJECTION UNIT 1 SP2000 - Screw diameter / type: 60 mm / thermoplastics - Effective L/D ratio: 23.3 - Injection pressure: 2420 bar - Shot volume: 792 cm³ - Shot weight at max. stroke for PS: 720 g - Injection speed: 140 mm/s - Injection throughput: 396 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 72.2 g/s - Nozzle contact force: 82 kN INJECTION UNIT 2 SP2000 - Screw diameter / type: 70 mm / thermoplastics - Effective L/D ratio: 20 - Injection pressure: 1877 bar - Shot volume: 1078 cm³ - Shot weight at max. stroke for PS: 981 g - Injection speed: 140 mm/s - Injection throughput: 539 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 98.3 g/s - Nozzle contact force: 82 kN ELECTRICAL PARAMETERS - Connected load: 341 kW - Power supply: 400 V / 50 Hz, 3 phases with neutral conductor WEIGHT & DIMENSIONS - Net weight: 43.5 t - L x W x H: 11.89 x 3.22 x 2.77 m ADDITIONAL EQUIPMENT - Wear-resistant plasticizing unit - BluePower full insulation for plasticizing cylinder - Open nozzle - BluePower ServoDrive - Pneumatic valve: 1-fold (BWAP), 1-fold (FWAP) - Pneumatic cascade valves: 6-fold (BWAP), 6-fold (FWAP) - Hydraulic core pull: 2-fold (BWAP), 2-fold (FWAP) - Mould heating: 96 zones (3.5 kW each) - Euromap interface for handling: E18 - Euromap central computer interfaces: E67, E77, E78, E63, E82.1 - Adaptive Process Control (APC+) - Graphic analysis package - Sliding table with turning unit, servo-driven Nsdpew U N Ixjfx Ab Ujwl - Vertical centre platen - Parallel clamping & opening during injection process with bar parallelism control between FWAP and centre platen or BWAP and centre platen - ColorForm interface signal interface for connecting an RPM unit - Electrical interface for HRS-Flexflow system - Electrical interface and hydraulic valves for "1-K dummy operation" - Interface for connecting a CoMo-Kistler Injection Basic System with good/bad part separation The machine is located at our plant in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your enquiry.

Year of construction: 2016, condition: ready for operation (used), The Coiltech Decoiler Straightener Feeder System is a compact press feeding system. Belt width: 600mm, material thickness: up to 6.5mm, straightening rollers: 7x115mm, decoiler tonnage: 6000kg, diameter (inner), min-max: 470-520mm. Connected load: 7.5kW, with documentation. Nwedpfxji El Uco Ab Uol

Condition: defective spare-parts repository (used), Year of construction: 2007, functionality: not functional, For sale is an injection molding machine of the brand Netstal and the type Synergy 1000-230 After a transportation accident, the control cabinet is completely defective. For this reason, the machine is offered as a spare parts carrier or for repair. Nsdpsrfbnmjfx Ab Ujwl Machine would be fully operational and in good condition Technical data: Operating pressure: 210bar, Injection force: 182kN, clamping force: 1000kN, Opening stroke: 0-400mm, mold installation height: 450-750mm Total weight: 7200 kg Operating hours: approx. 53,000 Available from March 2024 First fillings with hydraulic oil can be ordered from us On request, loading and transport (Europe-wide) can be organized for an additional charge. Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: excellent (used), Fully automatic filling machine, De Vree V 156 Filling capacity: 1-20 liters Automatic cap feeder Automatic cap closer In very good condition, directly from production!!! Nodpfx Aeztc Sgsb Ujwl

Year of construction: 1988, condition: excellent (used), machine/vehicle number: 3284, (min.) material thickness: 0.65 mm (max.) material thickness: 2 mm Technical Data: Width of film, max./min. 450/350 mm Forming area max. 430 x 160 mm Nwsdpohbu E Hsfx Ab Ujl Drawing depth max. negative/positive 6/20 mm (on request 22 mm negative) Top heater max. 10,15 kW Driving motors 3,0 kW Total connected load at 100 % duty cycle 12,7 kW Working air pressure 6 bar Air consumption (dependent on product) max. 1250 I/min Rate of water flow max. 1,0 m3/h COMPACT AND ROBUST - giving continuous high output. Easy and ergonomical operation (e.g. take- off height 1300 mm). QUICKLY CHANGEOVER - from 30° to 90° foil feed giving maximum material utilisation for both square and round lids. Heater changeover problem-free. PRECISION - The accuracy of the form table movement is guaranteed by linear guide bearings and hardened rods. The safe reliable guarantee for precision. OPTIMUM PUNCHING ACCURACY EVEN DURING MAXIMUM OUTPUT Cam controlled function sequence guarantees absolute precision with every cycle.

Year of construction: 2007, condition: good (used), Used 4.4kw Bystronic Byspeed CNC laser for sale Used Bystronic 4.4kw lasers for sale VIDEO BELOW: Byspeed 3015 4.4kw Installed new/year: 2007 Manufacturer: Bystronic Model: Byspeed 3015 Sheet size: 3metre x 1.5metre / 3000mm x 1500mm Laser power: 4.4kw / 4400 watt Control: ByVision CNC02 Automation n/a Year: 2007 Condition: good working condition / service from new Nwedsgwa Swjpfx Ab Uel Byspeed 3015 4400w March 2010 Power on: 44,189 hrs Cut time: 20,490 hrs Good condition machine that has been covered from new by service contract with Bystronic UK. Options Included: Bypos automatic focus CutControl 2 cutting heads Tools and accessories Torit Dust collector Delivery, installation and tuition available at extra cost.