Drinking water treatment plant

Lowara

Condition: new, Year of construction: 2024, Super special price, as it was on display at our in-house exhibition. Operating hours: 2 Available immediately - subject to prior sale If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Knjdjlht H Espfx Af Sjd Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg

Condition: new, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2025, Technical data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Total weight: 47,000 kg Fifth wheel load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3,750 mm Fifth wheel height loaded: 1,200 mm Steering radius to the rear: 2,300 mm Loading area length: 6,850 mm Extendable by: 5,500 mm Loading height with max. load: 350 mm Chassis length: 2,600 mm Loading height of rear chassis with max. load approx: 1,005 mm Suspension travel: -150/+450 mm Axle spacing: 1,360 mm Total width: 2,540 mm Total weight depends on fifth wheel load. Low bed: Low bed with external supports in extendable design "SUPER LOW" design, length approx. 6,850 mm. Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking. The supply lines are protected in the extendable supports and automatically adjust to the respective low bed length. 5 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 6 pairs of threaded blocks on the inner support for mounting screwable RUD rings. Rear chassis: Rear chassis with closed outer frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear. 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of tension rings lying in the trough (LC 8,000 daN+5,300 daN). 2 pairs of stake pockets for 100 x 50 mm stakes in the outer frame Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,785 mm. Gooseneck can be raised/lowered hydraulically and removed. Technical fifth wheel load: 23,000 kg For tractor units: 4 x 2, 6 x 2 and 6 x 4 PENDEL-AXLE: "PENDEL-AXLE", all axles hydro-mechanically forcedly steered. Hose rupture valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinder with shut-off valves and pins for securing in raised position. Final painting of the axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260". Technical axle load: 12,000 kg Hydraulic axle compensation. Axle tool. Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting cables to the tractor unit. Electrical system: Electrical system in accordance with EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets. Knsdpfx Asizu Nwjf Sed Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: Steel construction made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paint: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat in a single color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint possible. Tires: Tires 245/70 R 17.5 3PMSF At the manufacturer's discretion. Load index (146/146F) Preparation for screw-on container positioning for 1x 20' or 1x 40' container on the outer supports. Without container locks. i i2" kingpins iA galvanized steel bulkhead, approx. 400 mm high. iA spare wheel with holder in front of the bulkhead. i2 brake shoes with holder on the bulkhead. iYellow-red air couplings on the galvanized connection strip at the front. Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles. (without insta

Condition: excellent (used), Equipment: type plate available, Mobile tank systems for A1-A3 (KC diesel, KA gasoline/diesel and collection tanks), - double-walled, - 250 liters - 1000 liters, Knsdpfx Aogx E N Ijf Sed - partly with IBC approval, - 12V/ 24V/ or 230V pumps as required, - Automatic tap valve, - vertical or horizontal design, - partly with lockable pump covers, - on request with flow meter with daily and total counter, - all systems with new DEKRA inspection Loading and transport can be organized. Only serious and serious inquiries will be answered: Name, e-mail address and telephone number.

Condition: new, Year of construction: 2020, Electric elbow making machine is the mechanism for forming elbow from round and rectangular pipes with different diameters. Elbow making machine EEM-200plus is the better version of EEM-200 machine. It has additional fourth bottom pressing tool so it presses pipes from all four sides while bending and provides better quality of elbow. You can use our machine for working with round pipes as with rectangular pipes. Elbow making machine EEM-200plus lets you to work with pipes from 80 to 200mm. Pay attention: Inside diameter of the pipe you use for bending has to be 1mm bigger than bending matrix of the machine!! The lock of the pipe has to be closed or welded to avoid opening of pipe while bending!! Kodjf Epznjpfx Af Sond Elbow making machine EEM-200 is electric so it doesn’t need any air or oil system to work. Electric consumption is 1.5 kW/hour for this elbow machine. The needed voltage is 380V. It could be used in environment with temperature from -5 to +45 Celsius degrees. Elbow making machine is good for bending pipes with maximum thickness 0.8mm. Elbow making machine EEM-200plus bends elbows thank to special pressing tools. There is one set of tools for bending one diameter of pipe you need. So to bend more diameters of pipes you have to get additional pressing tools. It goes four pressing set tools with the machine so you can bend four diameters of pipes with it in the range from 80 to 200mm (that you choose by your own)

Condition: excellent (used), Year of construction: 2013, screw diameter: 38 mm, This machine is in storage at Plastima Used Machinery Kodpfx Afjvcqccs Ssnd

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Ksdpfx Afsu Thbxj Sond Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2018, condition: used, Multivac R270CD with skin pack and MAP pack. Overhauled in 2018, this machine came out of production week 37 2024. Machine comes with several moulds, spares and with 3 vacuum pumps incl. - Booster pump - Busch R5 360m3/h - Busch R5 100m3/h Only 668 production hours, everything build in. Good to go for production. Dimensions from all the tooling is in the photo album Knjdjuk Sp Nspfx Af Ssd

Condition: excellent (used), This system If designed to continuously cool veg products in glycol chilled water what was bought new by our customer to chill sachets of hot sauces and soups at 2500 KG per hour. Available separately or as a line with infeed and outfeed conveyors. Knsdpfx Afoh Uyg Nj Sed

Year of construction: 1995, condition: excellent (used), 2 units centrifugal pumps Sulzer MB 80-230/3 Flow rate: 79-89 m³/h Ksdpfx Afod Sybue Sond Head: 240-230 m Max. temperature: 130°C Seal: Mechanical seal with flush water connection Drive power: Siemens 90 kW Speed: 2980 rpm ! Price per unit !

Condition: good (used), Year of construction: 2024, Welding turntable KT 300 Knsdpfx Afjbvk I Eo Sed Load horizontal 300 KG, tilted 150 KG Power consumption 220V, 50 Hz table diameter 450mm height 500mm Tilt range stepless via crank gear motor 0 - 90°. speed 0,3 - 2,5 rpm Incl. foot remote control Surcharge: Quick release - jaw chuck diameter 300mm, 450.-€