Hopper for container

Condition: ready for operation (used), Year of construction: 1989, functionality: fully functional, machine/vehicle number: 1764, controller manufacturer: Fanuc, No minimum price – guaranteed sale to the highest bidder! MACHINE DETAILS Control: Fanuc Nsdpfx Aqjy Sluqevsct EQUIPMENT Accessories as shown in the pictures

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Nsdpfx Aovf E Avsqvjct Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, machine/vehicle number: 669, travel distance X-axis: 560 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 510 mm, controller model: MSC 502, rotational speed (max.): 12,000 rpm, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel X-axis: 560 mm Travel Y-axis: 510 mm Travel Z-axis: 510 mm Distance spindle center to table: 50 – 650 mm Distance spindle nose to table center: 100 – 610 mm Main Spindle Max. speed: 12,000 rpm Drive power: 22 / 18.5 kW Tool holder: MAS BT-40 Spindle bearing diameter: 70 mm Pallet Changer Number of pallets: 2 Pallet size: 400 x 400 mm Max. workpiece diameter: 580 mm Max. workpiece height: 650 mm B-Axis Switching time 90°: 2.5 sec Pallet changeover time: 6.0 sec Tool Changer Number of tool positions: 60 Max. tool diameter: 80 mm Max. tool diameter with adjacent magazine slots free: 125 mm Max. tool length: 300 mm Max. tool weight: 8 kg Tool-to-tool change time: 1.5 sec Chip-to-chip change time: 3.7 sec Rapid traverse (X/Y/Z): 32 m/min Feed rate: 1 – 24,000 mm/min Jog feed rate: 0 – 1,260 mm/min MACHINE DETAILS CNC control: MSC 502 Total power requirement: 63 kVA Dimensions & Weight Footprint approx.: 5.5 x 4.5 x 2.7 m Machine weight approx.: 9.0 t EQUIPMENT Documentation Chip conveyor Cooling device High-pressure coolant system Internal coolant supply Tool magazine: 60 positions Pallet changer Pallets: 2 Signal lamp B-axis Hydraulic unit Ncsdpfx Aey R U Ecsqvot Spindle oil cooler Note: Shaft for loading must be provided by the buyer.

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, turning length: 380 mm, turning diameter: 450 mm, spindle bore: 59 mm, rotational speed (max.): 5,000 rpm, controller model: Seicos 40L Multi, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Turning diameter: 450 mm Turning length: 380 mm Maximum machining diameter: 340 mm Travel X-axis: 215 mm Travel Z-axis: 400 mm Bar capacity: 51 mm Spindle speed range: 30 to 5,000 rpm Spindle drive power: 11 / 7.5 kW Nsdpfxey R Dmio Aqvect Spindle nose: A2-6 Spindle bore: 59 mm Bearing diameter: 100 mm Turret: 16 stations Feed rate: 0.001 to 500 mm/min Rapid traverse X/Z: 30 m/min Tool shank diameter: 25 x 25 mm Drill shank diameter: 40 mm Tailstock taper: MT 5 Tailstock quill stroke: 300 mm MACHINE DETAILS Control unit: Seicos 40L Multi Total power requirement: 23 kVA Dimensions & Weight Space requirement: approx. 5.5 x 2.8 x 2.2 m Machine weight: approx. 4.6 t EQUIPMENT Documentation Chip conveyor Tailstock Signal light Parts discharge chute Tool setting arm Work area illumination Tool holder

Condition: ready for operation (used), Drum Screen Terra Select. 50 mm screen perforation Ncsdpfxsvnmcve Aqvjt

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2010, operating hours: 26,000 h, machine/vehicle number: R1011250, laser power: 4,400 W, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 170 mm, workpiece weight (max.): 890 kg, Laser source and frequency converter have been renewed! TECHNICAL DETAILS Working Area and Cutting Area Nominal plate size X: 3,000 mm Nominal plate size Y: 1,500 mm Cutting area X-axis: 3,048 mm Cutting area Y-axis: 1,524 mm Cutting head Z-lift: 170 mm Workpiece weight: max. 890 kg Dynamics and Accuracy Positioning deviation: ±0.1 mm Positioning scatter: ±0.05 mm Edge detection accuracy: ±0.5 mm Positioning speed X/Y-axis (axial parallel): max. 80 m/min Positioning speed X/Y-axis (simultaneous): max. 113 m/min Axis acceleration: max. 4.5 m/s² Laser Source Laser power: 4,400 W Laser source: Bylaser 4400 Possible laser sources: Bylaser 3000 / Bylaser 4400 / Bylaser 5200 ARC / Bylaser 6000 MACHINE DETAILS Dimensions and required space Transport system standard height: 3,650 mm Transport system height to magazine: 4,350 mm Material trolley length: 3,000 mm Additional length for extension magnet: 200 mm Material trolley width: 1,600 mm Material trolley height without plate stack: 917 mm Standard lifting height: 550 mm Lifting height to magazine: 1,150 mm Lifting height with stacked tables: 800 mm Transport data and weights Travel unit with lifting unit: 1,300 kg Vacuum gripper frame with double fork system: 1,200 kg PLC cabinet: 500 kg Material trolley: 800 kg Total transport weight ByTrans 3015: 3,800 kg Equipment and Features Vacuum gripper frame plate thickness (loading): max. 25 mm Vacuum gripper frame plate weight (loading): max. 900 kg Number of vacuum grippers: 42 Weight per gripper: max. 45 kg Compressed air: 6 bar Vacuum: -0.6 bar Double fork system plate thickness (unloading): max. 25 mm Double fork system plate weight (unloading): max. 900 kg Fork travel path: 2 x 790 mm Cutting hours: 26,000 h EQUIPMENT ByTrans 3015 Extended Bylaser 4400 Shuttle table Loading arm Integrated 4th rotary axis Vacuum gripper frame Loading unit with suction gripper frame Double fork system Material trolley Vacuum pump Plate separator Double sheet detection Cassette trolley Air conditioning Control cabinet with signal lamp and emergency stop Ncedpfx Aoy Rt Ezoqvst Safety fence Photoelectric sensors ByTower storage system

Condition: repair required (used), functionality: limited functionality, machine/vehicle number: F20179V00607, Year of construction: 2019, operating hours: 7,419 h, load capacity: 2,000 kg, fork length: 1,000 mm, overall weight: 850 kg, total length: 2,333 mm, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Ncedpfxsy Rrz Ie Aqvet Load capacity: 2,000 kg Fork length: 1,000 mm MACHINE DETAILS Dimensions & weight Total weight: 850 kg Dimensions (L x W x H): 2,333 x 720 x 1,305 mm Operating hours: 7,419 h EQUIPMENT Charger Operation manual Note: 5 battery cells are defective.

Year of construction: 2011, condition: like new (used), functionality: fully functional, X-ray sorting machine. Nsdpfxeyy A Uwo Aqvect Manufacturer: TITECH TOMRA Model: X-TRACT 1200 The machine is in PERFECT WORKING CONDITION. Complete overhaul of the machine carried out. Source replaced: €35,000 All sensors replaced: €29,000 Belt replaced: €10,000 Applications: - Sorting of brominated plastics in WEEE streams - Sorting of metals - Sorting of wood, glass, and PVC for SRF production - Sorting of organic waste

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: F20179V00633, Year of construction: 2019, operating hours: 8,386 h, load capacity: 2,000 kg, fork length: 1,000 mm, overall weight: 850 kg, total length: 2,333 mm, No reserve price – guaranteed sale to the highest bidder! Ncedpfsy Rry Rox Aqvot TECHNICAL DETAILS Load capacity: 2,000 kg Fork length: 1,000 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 2,333 x 720 x 1,305 mm Total weight: 850 kg Operating hours: 8,386 h EQUIPMENT Charger Operator's manual

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, pressing force: 28 t, stroke length: 200 mm, throat depth: 200 mm, installation height: 325 mm, working length: 835 mm, TECHNICAL DETAILS Pressing force: 28 t Bending length: 835 mm Travel range of the back gauge: 0 - 370 mm Stroke: 200 mm Distance between frames: 890 mm Support table: 200 x 275 mm Overhang: 200 mm Installation height: 325 mm Number of cylinders: 1 Working speed Pressing speed: 8-10 mm/s Retraction: max. 35 mm/s Positioning accuracy: +/- 0.05 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 1,600 x 1,500 x 2,200 mm Ncsdpsy Rry Defx Aqvet Total weight: 3,500 kg EQUIPMENT Operating manual Safety device Mechanical tool clamping system (top)

Condition: new, SHAFTS DEDICATED FOR HAMMEL VB 850. ALSO AVAILABLE WITH SIDE COMBS PROTECHNIKA is a company with 21 years of history and, since the start of its operations, has been engaged in the production of spare parts and complete recycling lines. In recent years, we have expanded our portfolio to include the production of grinding shafts for slow-speed shredders. By implementing automated welding processes and developing our own manufacturing technology, we have minimized production times while maintaining consistent, high quality. Grinding shafts are a series-produced product, which, among other advantages, enables us to cooperate with machine manufacturers on an OEM basis. Nodex Hhfzepfx Aqvjct What sets PROTECHNIKA apart from the competition? It's simple! - Certified 3.1 materials - TUV SUD Rheinland quality - ISO 9001 - Automated welding process / ISO 15613 / ISO 15614 - ISO 9606-1 welder qualifications - ISO 9001:2015 - ISO 14001 - Independent design department capable of fulfilling any customer requirements - Our own RESEARCH AND DEVELOPMENT CENTRE Customer relations are of paramount importance to us, because their satisfaction is our success!

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 516305X00366, Year of construction: 2020, operating hours: 8,560 h, load capacity: 3,000 kg, power: 17 kW (23.11 HP), fork length: 2,400 mm, overall weight: 4,680 kg, No minimum price – guaranteed sale to the highest bidder! The forklift was brought from Italy to Germany as part of a relocation of several machines. TECHNICAL DETAILS Load capacity: 3,000 kg Fork dimensions: 2,400 mm x 120 mm x 50 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 4,813 x 1,200 x 2,775 mm Weight with battery: 4,680 kg Drive power: 17 kW Operating hours: approx. 8,560 h EQUIPMENT Ncedpfx Aqsy Rrx Tovjt Battery charger Note: The rear door is slightly damaged.

Condition: ready for operation (used), Year of construction: 1993, functionality: fully functional, machine/vehicle number: F 36905, travel distance X-axis: 7,000 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 1,300 mm, spindle speed (max.): 2,000 rpm, controller model: HEIDENHAIN TNC 360, TECHNICAL DETAILS Travel X-axis: 7,000 mm Travel Y-axis: 1,200 mm Travel Z-axis: 1,300 mm Rapid traverse x/y/z: 10 m/min Table size: 8,000 x 1,300 mm Table load capacity: max. 4 t/sqm Universal head: 5x90 plus manual 1 Tool holder: SK 50 Milling spindle speed range: 20 – 2,000 rpm Drive power: 30 kW Spindle torque: 2-speed gearbox, 750 Nm Ncedpfey Rrbhjx Aqvot MACHINE DETAILS Control: HEIDENHAIN TNC 360 Total power requirement: 50 kW Dimensions & Weight Space requirements approx.: 9.0 x 3.8 x 4.6 m Machine weight approx.: 25 t EQUIPMENT Orthogonal milling head, water-cooled 3D radio probe M&H 20.41 Partition wall for parallel machining/setup Internal air blast Internal coolant supply 15 bar Adapter for high-speed milling spindles with torque support Operator platform travels with machine Chip conveyor Electronic handwheel HR 410 Monitored safety fences Various optional accessories (angle milling heads, clamps, etc.)

Condition: excellent (used), Technical condition: very good Visual appearance: very good Please contact Ferdinand Pater for more information Ncedpfst Dltbex Aqvot

Condition: ready for operation (used), Year of construction: 2002, machine/vehicle number: 0-250-08-1590, functionality: fully functional, travel distance X-axis: 3,250 mm, travel distance Y-axis: 1,220 mm, travel distance Z-axis: 125 mm, controller model: Homatic 2000 IPC, number of spindles: 28, spindle speed (max.): 24,000 rpm, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Working area X-axis: 200 – 3,250 mm Nodoy Rmdqepfx Aqvsct Working area Y-axis: 70 – 1,220 mm Working area Z-axis: 12 – 125 mm (clearance 150 mm) Tool changer positions: 18 Spindles Total number of drilling spindles: 28 Vertical drilling spindles: 22 Horizontal drilling spindles in X-axis: 4 Horizontal drilling spindles in Y-axis: 2 Milling spindle power: 12 kW Milling spindle max. speed: 24,000 rpm C-axis: 360° interpolation MACHINE DETAILS Vacuum pump capacity: 100 m³/h Control model: Homatic 2000 IPC Control software: WoodWop 4.5 incl. MDE and production list software FEATURES 4 axes Console table 8 manually adjustable supports in X direction 3 vacuum cups per console Vacuum connection for templates Laser positioning aid for vacuum cups Laser projection for cup positioning Liquid circulation cooling Operator terminal Note: The sale does not include the pictured adapter units, tools, or HSK holders.