Used Fliegl Szs 260 Jumbo Mit Radmulden Und Tiefbett Für Lkw for sale (15,696)

Condition: new, machine/vehicle number: 3c70e9a5d82cfb3ada79baf95, empty load weight: 8 kg, maximum load weight: 17 kg, overall weight: 26 kg, axle configuration: 2 axles, tire size: 205 / 65 r 17,5, Further information Chassis semitrailer forwarding Welded fine-grained steel construction, fifth wheel plate with replaceable 2 kingpins, rear bevel to approx. 1920 mm, suspension bar for ramps at the rear and front on gooseneck, grinding rollers at the rear, drop center after cranking up to the axle unit. Drawing approval required from customer in case of order! Pair of lashing lugs at the top and side of the outer frame, 10 tons each Pair of lashing eyes embedded in the outer frame on gooseneck, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Folding rear support, mounted on the outside Wheel chocks with holder Aluminum side collision protection Steel underride guard for EG, if technically possible Quarter-shell mudguards with anti-spray flaps according to EG 1 pair of wheel recesses after gooseneck recessed in the low bed of the tramline area, sloping towards the entrance. Length at bottom approx. 1840 mm, depth of wheel recesses approx. 200 mm. 2nd pair of wheel recesses on rear slope. Depth approx. 200 mm. Note! Frame in main beam area 200 mm higher than wheel recess. In the event of an order, a precise technical inspection is still required. Wheel recess cover can be pulled out from the drop deck with hardwood inserts, on rear slope with hardwood inserts. Electric cable winch, 24 volt, pulling force 5500 kg, mounted in the offset gooseneck, not reaching into the loading area, operation with radio remote control, operation with radio remote control, cable length 35 m x approx. 10 mm, with roller cable window and removable guide roller on rear slope. Axles + suspension SAF or BPW drum brake axles of our choice Air suspension with lift & lower valve + auto-reset function Wheels and tires 205 / 65 R 17.5 tires with 129/127K (132/132G) marking for 8 to tire load capacity at max. 90 km/h at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS make Haldex, electronic brake system with EBS socket at the front, without connecting cable (sent to the customer for approval brake calculation.15.07.2021) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Psdpei Ri Hrjfx Akrspr Axle load detection via EBS-Canbus signal, for display via display in the cab, truck must be prepared accordingly, no truck instal. (no calibrated scales) Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Floor Gooseneck with steel / checker plate covering 30 mm screen-printed floor, in the drop floor between the longitudinal beams in the middleIn the tramline area covered with toothed grating in the wheel recesses with steel/checker plate covering. Access ramps Pair of aluminum ramps 3,200 mm long, load capacity per pair 12,000 kg Pair of steel ramps for entering the drop deck Pair of steel ramps for crossing on gooseneck Drop sides Approval / plates Country of approval: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Prepared for single-line license plate holder Contour markings with reflective strips to ECE R 048, yellow at the sides and red at the rear Warning sign according to ECE -

Condition: used, functionality: fully functional, machine/vehicle number: Fuhrpark, empty load weight: 6,000 kg, maximum load weight: 20,000 kg, overall weight: 26,000 kg, axle configuration: 2 axles, first registration: 04/2018, tire size: 205 / 65 r 17,5, Further information Welded fine-grained steel construction, saddle plate with replaceable 2 king pins Reinforcer mounting point for gallows mounting and with sturdy grinding plates drum profile made of flat steel underneath the outer frame. Outer frame slightly inclined with Load-Lock profile for attaching tension beltsNote! To attach the belts in conjunction with drop sides, the drop sides must be opened! 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder, aluminum side bumpers, offset inwards as far as technically possible, steel underride guard, as much ground clearance as possible, quarter-shell mudguards in front of and behind each axle, suspension strip for aluminum ramps at the rear, plastic toolbox, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) SAF drum brake axles, with axle stopsAxle distance 1600 mm, air suspension with lifting & lowering valve 205 / 65 R 17.5, twin steel rims, factory silver 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable front coupling heads, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 24 volt, multi-chamber lights, amber LED lighting integrated in outer frame profile at the side, offset inwards by approx. 25 mm, 10 lights per side 2 white position lights at the front, protected, 2 white/red lane departure lights at the rear, additional LED work light(s) at the rear, switched via reversing light 2 x 7-pin and 1 x 15-pin swap-proof sockets at the front, without connecting cable Psdpfx Akomp Ug Djrjpr Screen printing plates approx. 30 mm thick, for high point load capacity for forklift axle load up to max. 5,600 kg Special floor installation: test of new profiles, without bolting Steel/checker plate covering in the wheel arch area, front wall/front stanchions, 25 mm aluminum hollow profile, approx. 800 mm high, steel corner stanchions in volume design, with viewing windows on both sides. Approval country: Germany, with Dekra approval and certificate (according to §13 EG - FGV), 24/7 service hotline, prepared for single-line license plate holder, contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 14 kg, maximum load weight: 35 kg, overall weight: 50 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, tire condition: 100 %, Further Information Chassis Low-bed Semi-Trailer Steel welded construction, kingpin plate with replaceable 2" kingpin 24 t, 2-speed landing gear, single-side operation, with straight lower part, without shift equalizer Foldable rear support 2x wheel chocks with holders Side underrun protection made of aluminum Quarter shell mudguards in front of and behind the axle assembly With mud flaps behind each axle 1x storage box, w = 2,350 mm x l = 730 mm x h = 640 mm, bolted transversely to the front of the gooseneck, with 2 storage trays Extendable widenings to 3,000 mm (not at rear bevel end) (Track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for timber boards on the gooseneck, transverse at the front 70 mm timber boards for extension to 3,000 mm Excavator arm recess starting above the rear axles and extending to the rear, approx. 500 mm wide and approx. 230 mm deep Lashing eyes low-bed 3 pairs of 10 t lashing eyes at the front gooseneck, 8 pairs of 10 t lashing eyes in the low bed, 3 pairs of lashing rails in the driving lane area of the low bed, 3 pairs of 10 t lashing eyes at the axle/rear area Axles & Suspension SAF drum brake axles Axles/chassis laser-measured to reduce tire wear and fuel consumption With steering axle Air suspension Wheels and Tires 235 / 75 R 17.5 Manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system, color-coded line routing for easier service. Spring-loaded parking brake EBS, Electronic Braking System with EBS socket at front, without connection cable Attention: The trailer must only be towed by towing vehicles that ensure the effectiveness of ABS! 2 non-interchangeable coupling heads at the front, without connection line With raise & lower valve, hold function in lowered position + auto-reset function Axle load detection via EBS CAN bus signal, displayable on the cab display (truck must be suitably prepared, no truck installation incl., not a calibrated scale) Vehicle Driving Stability System Trailer Infocenter for displaying vehicle data such as axle loads (not a calibrated scale), mileage, and diagnostic/system messages. Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white front position lights in LED 2 white/red lane guidance lights at the rear 2x 7-pin non-interchangeable sockets at the front, without connection cable 1x additional LED work light at the rear, switched via reverse light 1x LED rotating beacon with holder, switched via parking light (removable beacon) 2 pairs of warning panels, double, LED illuminated and extendable to 3,000 mm Floor Gooseneck with steel / checker plate covering In the running lane area with 70 mm softwood flooring, in the wheel arch area steel / checker plate covering, low bed left and right in running lane area can be hydraulically raised, via truck auxiliary drive Rear bevel with 70 mm softwood decking Low-bed length approx. 6,300 mm Drop sides 25 mm aluminum hollow profile, 400 mm high, front and sides on gooseneck, plug-in Ramps Steel ramps, 2,800 mm long, 750 mm wide, side mo Pedpfei Ri Hgsx Akrjpr

Condition: used, maximum load weight: 28,410 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 01/2012, loading space length: 13,600 mm, loading space width: 2,400 mm, loading space height: 700 mm, FLIEGL flatbed semi-trailer with drop sides and 3 axles Payload: 28,410 kg TYPE: SDS350 Brakes: disc Axle: BPW + air suspension 2x landing legs (JOST) Length: 13.60 m Width: 2.40 m Height: 0.70 m Ppsdpfxowgghne Akrsr We are also happy to assist you with financing/leasing through our partners. All information without guarantee. Subject to errors and prior sale.

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Podji Ri Rvjpfx Akrepr Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, machine/vehicle number: eca976917d325d4adc41b69e8, empty load weight: 7,200 kg, maximum load weight: 27,800 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r 22,5, Further information Ppsdpfx Aji Ri Szjkrsr Chassis semitrailer forwarding Fine-grained steel welded construction in lightweight design, fifth wheel plate with replaceable 2 king pins, main frame reinforcement for 25 tons in the centre of gravity on 3 m loading length when pushed together. 13 pairs of hooks for lashing strap attachment welded onto the cross members 23 pairs of lashing eyes embedded in the outer frame, 3.5 tons each Outer frame with Load-Lock profile for lashing strap attachment Please note! Cannot be used with drop sides! 24 t. 2-speed support winch in reinforced design for loaded trailer, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation Wheel chocks with holder Aluminum side bumper Underride guard Half-shell mudguards with anti-spray flaps according to EG 1 spare wheel holder for 1 electric wheel, with wheel mounting kit 1 closed stanchion stowage box, open at the top, below loading area, doors on both sides, w=450 mm/H=400/420 mm/t=2460 mm 6 pairs of extendable stanchion pockets, for 80x80 mm tubular stanchions, extendable from loading width 2000 mm to 3100 mm 4 pairs of stanchion pockets embedded in the outer frame, for 80x80 mm shaped tubes 11 stake pockets centrally recessed in the floor, for 80x80 mm shaped tubes, with reinforcement beam, each installed between the outer stake pockets 5 x 3 pairs of stanchion pockets recessed on the outside of the longitudinal beams, for 80x80 mm shaped pipes, including reinforcement beams - for securing loads to the front and rear when transporting 2x5000 mm or 2x 6000 mm construction steel mats 6 lightweight stanchions W=80/ D=80/, usable height approx. 1850 mm, hot-dip galvanized, top with cable guide for belt tensioning 12 lightweight stanchions W=80/ D=80/, usable height approx. 1850 mm, hot-dip galvanized, with lashing eyes welded to the bottom on both sides Note: stanchion pockets / stanchions are not designed for securing long materials, pipes etc. on their own without looping around them 2 plastic toolboxes, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 6 construction steel winches with wire rope and counter hooks, with rope feed-through through the outer frame, 1 removable slip-on gear for construction steel winches - supplied loose (without bracket on the frame) Telescoping Main frame can be telescoped Extendable by max. 4,000 mm and can be arranged approx. every 500 mm Locking with pneumatic bolt locking + display Frame locking on both sides, actuation via hand knob, operation for brake/locking and suspension in FR-left in front of the axles Storage compartment between the side members when extended Axles + suspension SAF disc brake axles with 430 mm disc diameter Last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button, as well as manually via switch in the towing vehicle (pin 10), without truck installation. Offset axle spacing mm Air suspension 1st axle automatic lift axle, can also be operated electrically from the truck, with starting aid, without truck installation (starting aid is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored cable routing for easy servicing Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS make of the manufacturer's choice, electronic brake syst

Condition: new, machine/vehicle number: 1acf251a278ec5cde4067a7b1, empty load weight: 5,800 kg, maximum load weight: 22,200 kg, overall weight: 28,000 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 king pins Outer frame slightly slanted new design with Load-Lock profile for tensioning strap attachment 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Free support foot corner dimension or free swing radius to the rear approx. 1920 mm 2 wheel chocks with holder Aluminum side impact guard Steel underride guard Quarter-shell mudguards in front of and behind each axle 1 spare wheel holder for 1 e-wheel, with wheel fastening set 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Axles + suspension Drum brake axles of the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-applied parking brake Duomatic connection at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable Floor Screen printing plates approx. 30 mm thick, for high point load capacity for forklift axle load up to max. 5,600 kg Front wall / front corner stanchions 25 mm aluminum hollow profile, approx. 1 350 mm high, steel corner stanchions in volume design Approval country / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Pedokv Uvzopfx Akrspr Front wall aluminum Attention! These are archive pictures!

Condition: new, machine/vehicle number: 56c59c8aba35227ffb44c9f75, empty load weight: 11,350 kg, maximum load weight: 26,650 kg, overall weight: 38,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis Jumbo semi-trailer Welded steel construction with narrow cross member spacing and reinforced design, low loader external frame profile, for transporting construction machinery up to 32000 kg and up to a max. external width of the construction machinery of 2550 mm, fifth wheel plate with replaceable 2 king pins. Rear inclination to approx. 1200 mm and 7°. Ramp shaft closed at the top with steel/checker plate, In the low bed Omega rail on the side at the bottom of the outer frame as a suspension strip for tarpaulin and spacer for the lashing points, not in the wheel area. With lift table on an additional fixed lightweight outer frame with omega profile, lift table can then be raised with closed tarpaulin! 24 t. 2-speed support winch, single-side operation, with semicircular lower section and straight connecting plate, with thrust compensation, free swing radius to the rear approx. 1950 mm, Folding rear support 2 wheel chocks with holder Aluminum side bumpers Ppjdpfoi Riw Aox Akror Quarter-shell mudguards in front of and behind each axle With anti-spray flaps behind each axle Steel underride guard Rear spray flaps across the entire width 4 stainless steel storage box, w=800/h=350/t=350 mm, with polished door, lockable 2 x in FR-left and 2 x in FR-right in front of the 1st axle Lifting table to gooseneck, approx. 3000 mm long, can be raised hydraulically for transfer to gooseneck, with mechanical locking when raised. (inclined cylinder for good ground clearance, Fliegl standard). Operation in FR-right + additional operation with radio remote control (same as ramp operation) Lifting table can be raised with closed tarpaulin! Tarpaulin suspension in the lift table area on an additional fixed lightweight outer frame with Omega profile, lift table can be raised with closed tarpaulin! Lashing mushrooms can also be used when lowered! Lashing eyes Gooseneck: 4 pairs of 5 to lashing eyes embedded in the outer frame 2 pairs of lashing points at the top and sides of the outer frameLow bed 8 pairs of lashing mushrooms at the top and sides of the outer frame, each 10 tons 9 pairs of 5to embedded in the outer frame Axles+suspension SAF drum brake axles last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lift & lower valve + auto-reset function H & S function with quick air release 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage Wheels and tires 235 / 75 R 17,5 from leading manufacturers Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection in the truck via EBS, without truck instal. (no calibrated scales) Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front, in LED 2 white/red lane departure lights at the rear, 1 rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illum

Condition: new, machine/vehicle number: 207ad28f83705ed0d38a4f174, empty load weight: 3 kg, maximum load weight: 11 kg, overall weight: 14 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 flush with rear (for 7.15 swap bodies not flush with rear, forklift pockets/frame protrude) Telescopic front support leg 1 pair of front gear support legs, with straight lower section and single-sided operation in FR right Wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguards Bracket for truck-mounted forklift at the rear, including 2 fork pockets, 2 extendable support tubes, bracket for chain safety device with pin. Underride guard with light unit can be folded away. Including 2 loose rubbers to protect the rear wall, we recommend counterweight! Partially low ground clearance with forklift, poor tracking behavior possible, without warranty! (Forklift tare weight up to max. 1500 kg for trailers). (With proximity switch for forklift control in conjunction with lift axle)The axles are shifted to the rear by the forklift bracket, observe load distribution when driving without forklift. Customer risk! (For swap body trailers, driving with a forklift is only permitted in conjunction with a swap body) Forklift bracket as AU 203670 adapted to 7.45 m swap bodies Counterweight at the front between the frames, approx. 300 kg, if necessary, exact check still required Towing device central axle trailer Tow bar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required if ordered) Lower coupler drawbar without length adjustment drawbar Axles + suspension SAF drum brake axles of the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-applied parking brake Duomatic connection at the front, with connection line to the engine trolley, in FR-left Duomatic connection at the front, with connection line to the motor vehicle, connection in FR-right EBS, electronic brake system with EBS plug at the front, with connecting cable, in FR-left Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in each case in lowering / lifting position Vehicle - driving stability system Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Ppodoi Ri Iaepfx Akrjr Steel rims in twin arrangement, factory silver Electrical system 24 volt, 4 x 3 chamber lights + 1 round reversing light and + 1 round rear fog light, amber LED lighting on the side, lights mounted in a protected position! 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin plug at the front, with connecting cable, in FR-left 2 x 7-pin sockets in FR left rear for truck-mounted forklift 1 x 15-pin socket in FR left rear for truck-mounted forklift LED work lights on both sides behind the 2nd axle (switched via reversing light) Additional LED work light(s) at the rear, switched via reversing light Approval / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame

Condition: new, machine/vehicle number: e7fbe178b85a202cade7e95af, empty load weight: 5 kg, maximum load weight: 22 kg, overall weight: 29 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis saddle forwarding Welded fine-grained steel construction, saddle plate with replaceable 2 king pins, with 2 king pin positions Slightly angled outer frame with load-lock profile for attaching lashing strapsNote! To attach the straps in conjunction with drop sides, the drop sides must be opened! 2 pairs of lashing eyes embedded in the outer frame on gooseneck, 5 tons each 8 pairs of lashing eyes embedded in the outer frame in the low bed, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminum side bumper Steel underride guard Quarter-shell mudguards in front of and behind axle unit 2 Stainless steel stowage box, w=600/h=400/t=500 mm, with polished door, lockable 2 pairs of stake pockets recessed in the outer frame on gooseneck, 70 x 40 mm internal dimensions 6 pairs of stanchion pockets in the outer frame recessed in the deep bed, 70 x 40 mm Internal dimension!!! Internal width between the stanchions 2420 mm!!! 3 lashing/stanchion rails in the drop-down bed, embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 mm. Piece of stanchions W=80/ D=50/ L=1200 mm, hot-dip galvanized Piece of stanchions W=80/ D=80/ L=1200 mm, hot-dip galvanized Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Mechanical rear extension with hand crank, can be extended by approx. 1,500 mm, can be locked every 500 mm, with support beam, can be loaded with 2000 kg over the entire width at the load center of gravity at approx. 500 mm, can be loaded with 1000 kg over the entire width at 1000 mm and can be loaded with 500 kg over the entire width at 1500 mm, incl. extendable underride guard with lighting, 2 pairs of stanchions W=80/ D=80/ L=1200 mm, hot-dip galvanized Open storage compartment for stanchions, on the front wall or underneath the loading area (for 10 stanchions 80 x 50 x 1200 mm and 4 stanchions 80 x 80 x 1200 mm) Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales). Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin sockets at the front, without connecting cable Ppodpsi Ri Hvjfx Akrer 2 additional LED work lights, at the rear, switched via reversing light 1

Condition: new, machine/vehicle number: dc46d2e1cd272305b99fb3160, empty load weight: 9,800 kg, maximum load weight: 31,200 kg, overall weight: 41,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Vehicle consisting of: Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit 1st pair of wheel recesses after gooseneck recessed in the low bed of the tramline area, slanted towards the entrance. Length at bottom approx. 1600 mm, depth of wheel recesses approx. 260 mm. Note! Frame in main beam area 260 mm higher than wheel recess. 2nd pair of wheel recesses between A and B axle. Bottom length approx. 350 mm, depth approx. 260 mm. Note! Frame in main carrier area 260 mm higher than wheel recess. If wheel loaders are to be driven and the overall height is to be checked, we request a technical data sheet for the wheel loader types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses are required by the customer). Wheel recess cover can be pulled out from the main frame, with wooden inserts. Widenings extendable to 3,000 mm (not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 2 pairs of ring lashing eyes, 5 tons each at the front on the gooseneck 11 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x on gooseneck9 x in low loader bed distributed first lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, or instead of stake pockets 5 to. Ring lashing eyes embedded in the floor Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Ppsdpji Ri Hcofx Akrjr Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm, removable with plug Floor Gooseneck with steel / checker plate covering Storage box embedded in drive-over slope to gooseneck Then with 70 mm softwood floor, in the wheel recesses underneath and in the wheel

Condition: new, machine/vehicle number: df0bcd99c5751964e020b1055, empty load weight: 6 kg, maximum load weight: 14 kg, overall weight: 21 kg, axle configuration: 1 axle, tire size: 235 / 75 r 17,5, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with replaceable 2 kingpins, low bed from wheel area to gooseneck sloping to approx. 210 mm loading height, rear sloping to wheel area, suspension bar for aluminum ramps at the rear across the entire width Wheel chocks with holder Aluminum side bumpers Wheel cover with galvanized sheet steel, removable 1 towing eye at the rear, 10 to. Ppjdpfx Aksi Ri Hksror Spare wheel with holder on front wall/stowage box outside front Steel storage box on gooseneck at the front, transverse, approx.: L = 2400 mm, W = 400 mm, H = 600 mm, lockable Electric cable winch, 24 volt, pulling force 8165 kg, mounted at the front on gooseneck behind the stowage box on loading area, operation with radio remote control, cable length 35 m x approx. 10 mm, with roller cable window and 2 removable guide rollers on gooseneck and rear flange. Nato socket on connection plate 1 pair of wheel recesses approx. 700 mm after the gooseneck, starting in the floor recess, open to the outside. Note: Main frame protrudes approx. 145 mm.4 pairs of plug-in positions for wheel stops (Fliegl standard), without wheel stops for parking the semi-trailer approx. 100 mm high and approx. 100 mm long Piece of plug-in wheel stops When transporting SZM, an approx. 50 mm shim is placed in the front wheel wells approx. 50 mm high, approx. 1200 mm long, approx. 500 mm wide Low loader lashing eyes 2 pairs of 2.5 to lashing eyes on gooseneck7 pairs of lashing mushrooms embedded in the top and sides of the outer frame, 10 to each 4 pairs of 10 to lashing eyes embedded in the top of the main frame side member1 screw lashing eye with 6.7 to each (JDT) at the rear in the middle of the ramp storage compartment1 additional folding lashing eye at the front of the drop deck, 10 to each Axle + suspension SAF drum brake axle, Air suspension with lifting & lowering valve Wheels and tires 235 / 75 R 17,5 from leading manufacturers Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnoses may occur although the function is given) 2 white front position lights in LED 2 white/red rear lane departure lights in LED 2 x 7-pin and 1 x 15-pin interchangeable front sockets, without connecting cable LED rotating beacon with holder, switched via parking light (light can be removed) Additional LED work light(s) at the rear, switched via reversing light Floor Gooseneck with steel / checker plate covering Deep loading area perforated steel plate, steel / checker plate covering in the wheel recess area and removable sheet metal covering in the wheel housing area Rear slope with perforated steel plate Drop sides Aluminum, 400 mm high, laterally on gooseneck, pluggable, approx. 2500 mm long Rear wall aluminum, 400 mm high, on gooseneck, pluggable Drive-on ramps Pair of aluminum loading ramps max. load capacity 12,000 kg per pair, length approx. 3400 mm and width approx. 320 mm, storage compartment for ramps 1 x between the longitudinal beams at the rear Operating instr

Condition: new, machine/vehicle number: 1f4581c873ed977cb9602039b, empty load weight: 3 kg, maximum load weight: 34 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis semi-trailer container Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Container mounts: 1 x 20 foot centered (or swap body container 7.15 / 7.45), not retractable at the front, the pivot pins of the container lock in the longer version 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Side collision protection Aluminum underride guard Half-shell mudguards with anti-spray flaps according to EG VA drip tray with 1 1/4 inch drain pipe + 1 1/4 inch stopcock, incl. drip tray, with perforated tread plates, approx. 400 mm wide, left + right between drip tray and side member 4 hose trays approx. 4500 mm long (hose box) for hose pipes 2 x DN 200 outside + 2 x DN 160 centrally arranged, rear hose box (stainless steel) 300 mm deep, splash-proof, cover (stainless steel) with rubber seal all round, with drain hole at lowest point, then without cover on hose pipes Podpfoi Rixkex Akrepr 1 stainless steel earthing lug at the rear in FR on the right of the frame, with international earthing sticker on the frame, Steps at the rear right on the underride guard, at the rear in FR right on the outside of the main beam, tread plate approx. 260 mm long and 300 mm wide, Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored cable routing for easy servicing Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) This vehicle may only be loaded with 20' tank containers that comply with ISO 668 and in particular ISO 1496-3! The tank containers must have "end-load-transfer areas"! Country of approval / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Approval according to ADR acc. to 9.1.1.2 of ADR, EX/II, EX/III / certificate of approval for vehicles for the transport of certain dangerous goods (ex.B3) with warning sign at the rear, not valid for substances according to UN 0331 and 0332 (explosives B-E) Contour marking with refle

Condition: good (used), Year of construction: 2020, functionality: fully functional, type of input current: three-phase, total width: 4,500 mm, total length: 4,500 mm, input voltage: 400 V, working width: 2,000 mm, cutting width (max.): 2,000 mm, We offer a camera-assisted CNC cutter for single-layer cutting of textiles and leather. With the integrated image processing system, shapes and designs can optionally be recognized and cut with precision. The machine has low operating hours and is in perfect working condition! Pedpjyx I Duefx Akrepr

Condition: new, maximum load weight: 26,500 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 13,450 mm, loading space width: 2,550 mm, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, WIESE 3-Axle Low Loader with Ramps and Wheel Wells – NEW Availability: approx. 4 months from order --- Vehicle Data Manufacturer: WIESE * Type: WSA 3-36 TL * Year of manufacture: 2025 * Axles: 3 * Gross vehicle weight: 39,000 kg * Fifth wheel load: 12,000 kg * Axle unit load: 27,000 kg * Unladen weight: approx. 9,500 kg * Tyres: 235/70 R17.5 * Brakes: WABCO EBS with RSS --- Dimensions * Load platform length: 13,450 mm * Low bed length: approx. 9,550 mm * Fifth wheel section: approx. 3,640 mm * Overall width: 2,550 mm * Low bed loading height: approx. 920 mm * Fifth wheel height: approx. 1,250 mm --- Features * 3 SAF axles (9 t) with air suspension * 1st axle lift axle * 3rd axle trailing steering axle (lockable) * Electronic air suspension E-TASC * WABCO EBS brake system with Roll Stability Support * Tyre pressure monitoring system for 12 tyres * Full LED lighting * 4 x LED work lights * 15-pin + 2x 7-pin power sockets --- Structure * Robust steel frame * 28 mm hardwood floor / Omega deck * 13 pairs of lashing rings (8,000 kg) * Additional lashing points (5,000 daN) * 2 pairs of wheel wells * Excavator arm recess * Removable aluminium side boards on the gooseneck * Front toolbox --- Ramps * 2 x aluminium access ramps * Dimensions: approx. 2,800 x 600 mm Ppedoyuq Igspfx Akrsr * Load capacity: 27,460 kg * Spring lifting mechanism * Laterally adjustable --- Miscellaneous * Warning boards for oversize up to 3 m * Conspicuity marking according to ECE-R48 * Technical documentation and TÜV certificate For further information, please do not hesitate to contact us.

Condition: used, Year of construction: 2005, container length: 24 ft, overall weight: 16,000 kg, empty load weight: 3,250 kg, loading space width: 2,480 mm, loading space length: 7,300 mm, loading space height: 2,720 mm, machine/vehicle number: 610272 8, JUMBO BDF swap body swap body with roller shutter * beaded steel box body * Crane and stackable * Length 7.45 m * Roller shutter door Ppsdpei Avlljfx Akrjr * Interior keyhole panel * Screen printed floor * neutral white WITHOUT labeling! * Guide tunnel at the front slightly deformed * Slight rust on frame and body * Parking height: 1.02 - 1.32 m * Loading height at the roller shutter: 2,620 mm * External height: 3,000 mm * UVV inspection on request new * Manufacturer: KRONE Delivery possible nationwide! We always have larger quantities of different manufacturers and designs for sale or for RENT in stock !!! All prices net plus VAT!

Year of construction: 2026, operating hours: 1 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S22EVA_07, Exhibition machine - like new. Podpfx Aksykuhcorjpr EVA Turntable / base frame increased / Ø 1,500 mm Max. pallet dimensions: 800 x 1,200 mm Max. load capacity: 1,500 kg Wrapping height (pallet included) 2,200 mm Raised base frame by 150mm - 200mm, for charging with E-Ant - adjustable Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL All function parameters can be set via the display F02 - Infinitely variable turntable speed 5-12 rpm Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Pallet wrapping height setting F62 - Ergonomic height for film change ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 1 storable wrapping program F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - manual winding F12 - winding to a stored height (while switching off the light button) F29 - Soft start cycle for edge protection application Soft start to reduce film tears on sharp pallet edges FILM SLIDE TYPE “FM” WITH MECHANICAL BRAKE via manually adjustable brake roller on the foil carriage Foil specification Max. outer diameter Ø 250 mm - core Ø76mm - height = 500 mm Standard connection values: 230 V - 1L+N+PE - 50 HZ Total power: 1.2KW / 6A Other systems are immediately available from stock.

Year of construction: 2026, operating hours: 2 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S22EVA_03, Exhibition machine - like new. EVA Turntable / base frame increased / Ø 1,500 mm Max. pallet dimensions: 800 x 1,200 mm Max. load capacity: 1,500 kg Wrapping height (pallet included) 2,200 mm Raised base frame by 150mm - 200mm, for charging with E-Ant - adjustable Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL All function parameters can be set via the display F02 - Infinitely variable turntable speed 5-12 rpm Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min Psdpeykud Djfx Akropr F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Pallet wrapping height setting F62 - Ergonomic height for film change ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 1 storable wrapping program F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - manual winding F12 - winding to a stored height (while switching off the light button) F29 - Soft start cycle for edge protection application Soft start to reduce film tears on sharp pallet edges FILM SLIDE TYPE “FM” WITH MECHANICAL BRAKE via manually adjustable brake roller on the foil carriage Foil specification Max. outer diameter Ø 250 mm - core Ø76mm - height = 500 mm Standard connection values: 230 V - 1L+N+PE - 50 HZ Total power: 1.2KW / 6A Other systems are immediately available from stock.

Year of construction: 2026, condition: new, Our KVK 1A is the almost identical sister model to the KVK 2 (MA), i.e. a semi-automatic stretch wrapper with turntable which, in comparison to the KVK 2 MA, is equipped with a cut-out for ground-level access with a hand pallet truck. The only thing that still has to be done manually with this wrapper is feeding and cutting the film. With a weight of 700 kg, this model is also designed for professional use and can be loaded up to 1500 kg. Psdpfx Aey Drhzekropr The 1A has a turntable of 1500 mm and can wrap pallets up to 2400 mm high as standard. With adjustable speeds of the turntable and film carriage, as well as an electromagnetic brake that can be very finely adjusted via potentiometer, you can adapt the automated wrapping process perfectly to your product. Automatic recognition of your pallets (via photocell) is just as much a matter of course as adjustable head and foot wrapping. Programs are available for "up only" wrapping, "up & down" (cross wrapping) and "rainproof" wrapping. If required, the winder can also be controlled manually. If the winder needs to be used at a different location in between, it can be easily lifted and moved with a forklift using the integrated cut-outs. In addition to a photocell for detecting dark packages or black film, the wrapping height of the KVK 1A can be varied as an option (up to 3200 mm). Recommendation The KVK 1A is ideal if no ramp can be used for space reasons or if particularly heavy or unstable packaged goods are not to be pushed onto the turntable via a ramp. For further information, we have attached the technical data sheet as a PDF to this advertisement!

Year of construction: 2026, condition: new, Our KVK 1A is the almost identical sister model to the KVK 2 (MA), i.e. a semi-automatic stretch wrapper with turntable which, in comparison to the KVK 2 MA, is equipped with a cut-out for ground-level access with a hand pallet truck. The only thing that still has to be done manually with this wrapper is feeding and cutting the film. With a weight of 700 kg, this model is also designed for professional use and can be loaded up to 1500 kg. The 1A has a turntable of 1500 mm and can wrap pallets up to 2400 mm high as standard. With adjustable speeds of the turntable and film carriage, as well as an electromagnetic brake that can be very finely adjusted via potentiometer, you can adapt the automated wrapping process perfectly to your product. Automatic recognition of your pallets (via photocell) is just as much a matter of course as adjustable head and foot wrapping. Programs are available for "up only" wrapping, "up & down" (cross wrapping) and "rainproof" wrapping. If required, the winder can also be controlled manually. If the winder needs to be used at a different location in between, it can be easily lifted and moved with a forklift using the integrated cut-outs. Ppjdpfx Akey Drfysrjr In addition to a photocell for detecting dark packages or black film, the wrapping height of the KVK 1A can be varied as an option (up to 3200 mm). Recommendation The KVK 1A is ideal if no ramp can be used for space reasons or if particularly heavy or unstable packaged goods are not to be pushed onto the turntable via a ramp. For further information, we have attached the technical data sheet as a PDF to this advertisement!

Condition: excellent (used), Year of construction: 1992, functionality: fully functional, Tilting Spindle Moulder KÖLLE F45 with power feed and integral fence Very good condition; the machine comes from a small model making workshop and has only seen light use. Everything works perfectly. All bearings and guides are in proper condition; the machine runs extremely smoothly. Year of manufacture: 1992 The moulder fence features one adjustable jaw with fine adjustment and scale, enabling jointing operations such as for gluing profiles. The entire fence can also be accurately and quickly adjusted in depth via a handwheel and leadscrew, with the milling depth displayed digitally. Spindle locking by lever. The machine is equipped with an eye-level control panel. Fitted with AIGNER integral fence. Efficient chip extraction with two extraction ports (125 mm and 100 mm). Equipped with a 30 mm spindle, continuously tiltable from -5 to 45°, tilting is electrically operated; for fine adjustment, there is a handwheel and digital readout. A 40 mm spindle can also be installed. Reverse/forward rotation capability. Nationwide personal delivery and demonstration within Germany for €220, eliminating all risk on purchase. Shipping to Austria and other EU countries available on request. Large table opening, adjustable by multiple insert rings (enabling use of both large and small diameter cutters with optimal safety). Spindle speeds: 3000, 4000, 5000, 6000, 8000, and 10,000 rpm. Spindle height adjustment is also electric, with fine adjustment via handwheel and digital readout. Includes 2200 mm long extendable auxiliary support. Very robust and durable construction, built for heavy-duty milling tasks and suitable for all routing operations. Optimal power transmission via belt drive system. Supplied with operating manual. Includes 4-roller HAFFNER power feed, model 904. The feed unit features forward/reverse operation and 4 speeds, with individually mounted feed rollers. Machine table is 1200 mm wide and 1000 mm deep, with 500 mm table extensions on both left and right sides. Ready to use immediately. 380V, 6000 and 8600W motor thanks to two speed ranges; fitted with a heavy-duty motor. Comes with all necessary safety features, including motor brake and emergency stop. The machine is certified by the Woodworkers' Professional Association and carries the GS tested safety mark. Weight: approx. 1000 kg Fitted with motor overload protection. Professional-grade machine, not DIY store quality. Ppjdpfx Akjy Hxtpsrer Optimal, simple, fast, and safe handling.

Year of construction: 2026, operating hours: 1 h, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S25MythoSarya05, Mytho S with TP / Transparent, accessible at ground level with lift trucks and El. lifts. MAST VERSION Winding height 2450 mm 99 program Ppedpfxjykuh Ne Akror TOUCH display 7" FILM SLIDE TYPE "PRS" (POWER ROLLER STRETCH) 200% pre-stretching Optionally, more or less pre-stretching possible TURNTABLE / TP Ø1650 mm / Opening 06.00 - Mast 12.00 (can be changed at any time) ARYA system for automatic foil blowing and cutting, incl. infrared remote control

Condition: refurbished (used), hydraulic feed drive unit, fully reconditioned, stepless variable; Ppodpfx Aksirmulsrjr 1 unit for KME 2 or BM - right execution - without additional pump - type 56-009

Condition: new, New spacer rings for PAUL KME 2 and BM, with bore diameter 75 mm, outer diameter 120 mm, in widths 41, 30, 26, 22, 20 and 10 mm, new spacer rings for PAUL K2V, with bore diameter 60 mm, outer diameter 90 mm, in widths 40, 30, 20, 10, 2 and 1 mm, Pjdpfx Ajh Anyfokrepr Saw bushings for saw shafts with diameters of 60 mm, 50 mm, 45 mm and 40 mm, new hard-chromed CV saw blades in various diameters for KME 2, BM and K2V

Condition: new, Year of construction: 2026, Dosing ranges: 1 ml - 38 ml 2 ml – 100 ml 5 ml – 250 ml 20 ml – 680 ml 50 ml – 1,500 ml Volumetric filling Under-surface filling possible Pedewpr Uxopfx Akropr Special "Anti-Drop" device Adjustable filling nozzle Pump and filling nozzle made of stainless steel AISI 316 L Automatic cap application Stepless torque adjustment of the screwing system Closing system for plastic caps Touch display control The products can come from the food, cosmetics, pet food, oils, chemicals and other industries (always subject to technical evaluation). The pouches are manually hung into a special rail feed system. Then the machine transports the empty pouches into the star. There, the pouches are volumetrically filled, the caps are automatically applied and then automatically closed. The torque is adjustable. The machine is compact and very versatile. Also available as a semi-automatic monoblock.