Stationary shredder

Metso M&J 4000S

Condition: excellent (used), Year of construction: 2013, operating hours: 11,347 h, functionality: fully functional, machine/vehicle number: 50433-115-4291, Power supply: Voltage 400 V AC, 50 Hz, Main motor power 2 X 200 kW, Main switchboard, rated current 760 A. Main motor, full load current 2 x 341 Amp, PLC controller. Drive principle, hydrostatic transmission with power consumption limiter. Working, cutting cassette: 2 asynchronously operating shafts. Speed ​​33 rpm. Number of rotary knives 2 x 12 pieces, number of lower, fixed knives 2 x 24 pieces. Bearings 2 x 2 barrel. Drive system after general renovation - pumps, engines. The M&J waste shredder is an ideal solution for shredding various types of waste, industrial, municipal. The waste is shredded using one or two rotating shafts equipped with spirally mounted knives, which ensures optimal shredding of the material. The waste shredder is equipped with a fully automated control system that monitors the device's operation and protects it from overload. The device consists of modules, which is why it is a very flexible solution. Dwjdpfxoh Nu Tvj Addjf

Condition: refurbished (used), Year of construction: 2018, Mobile hammer mill Mobil Flex 1000 with drum magnet and discharge belt Drive: 250 Kw electric 4-hydraulic supports for lifting the machine for transportation Total weight: 33,000 kg Rotor weight: 3,000 kg Production: up to 11 to/h (depending on material size, grid size, parameter settings) With soundproof housing Dimensions: 11,750 x 2,500 x 4,380 mm Dwodjph Uy Tjpfx Addef Number of hammers: 24 pcs. Hammer weight: 22 kg System is being overhauled

Year of construction: 1999, condition: excellent (used), BARREL NEW Dwjdpfx Aelqw I Ijddef CORRECT TRUCK REGISTERED

Condition: new, Year of construction: 2024, Ring Rolling machine ZOPF - model ZB 30/3 MD TECHNICAL SPECIFICATIONS: - three driven shafts, smooth surface - manual adjusting of the center roller - working position horizontal and vertical (optional) - digital readout - shafts are supported by conical bearings - slide bars on the slide-support are exchangeable - shaft diameter: 20 mm - roller diameter: 76-86 mm - shaft rpm: 11 U/min - voltage: 400V 50Hz 3Ph - drivingmotor: 0,18 kW - adjusting way: 35 mm - weight: 85 kg - dimensions: 530x420x500 mm Dwodpfx Adodktnvedof

Year of construction: 2023, condition: new, Screening plant SEBA double drum 26 Standard version - according to the following technical description: DIMENSIONS length: 6175 / 6350 mm width: 2100 mm height: 3335 mm Weight: 3300 kg Maximum speed: 80 km / h WORKING DIMENSIONS length: 6175 / 6350 mm width: 6050 mm height: 3200 mm loading height: 2350 mm FACTIONS 2 or 3 fractions with optional slip-on ring. Mesh size fraction 1: 0mm - 10mm (adjustable) Mesh size fraction 2: 10mm - 70mm (adjustable) Mesh size fraction 3: 70+ mm (adjustable) POWER: 5-35 m3 / hour Dwedpfxjiy Nrgj Addof Power supply: 16A min / 10kVA full electric Power consumption: approx. 8,5 kWh Optional Transport of the emergency power unit in the screening plant possible (Subject to technical changes)

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Dwsdpfxju Thhro Addjf Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2024, condition: new, The mini pallet shredder is ideal for shredding small and/or dismantled pallets. Dedjpahwvepfx Addowf

Condition: like new (used), Year of construction: 2008, functionality: fully functional, mobile shredding machine - used- rebuilt - Arjes 760 D with magnet on wheelaxle Complete conversion to hydraulic drive -- High Performance Shredder -- the most powerful shredder in this size for heavy applications RECONSTRUCTION Machine was completely dismantled and rebuilt by steel construction. Conversion to hydraulic drive system Engine: Mercedes Benz OM 471 Stage 3 350 KW / 477 HP!!! (without AdBlue) - Gearbox: SYNCHRONOUS: 2x125,000NM - Hydraulics: Bosch Rexroth -- 285cbcm pump + 2x 215cbcm hydraulic motors - Control: NEW - Hydraulic lines: NEW - Radio: NEW - Shafts / tools: NEW Dwedpfxev Dtfvs Addof (Combined tool for wood, garbage, light scrap) Machine is equipped with secondary crusher bars WERT GmbH is a metalworking company specializing in the development and production of twin-shaft shredding tools for renowned brands such as Hammel, Arjes, Linder, Eggersmann, Terex, and Keestrac. With an in-house design department and a highly skilled team, we provide customized, innovative solutions that meet the highest quality standards. Our goal is to continuously meet the individual needs of our clients through technological excellence and improvement. We serve companies across various sectors, including waste management, recycling, and mechanical engineering, and place great importance on long-term partnerships. With our reliable and high-performance shredding solutions, we help our clients increase their efficiency and competitiveness.

Condition: good (used), functionality: fully functional, power: 122 kW (165.87 HP), fuel type: diesel, color: green, Year of construction: 2006, machine/vehicle number: 830.0.354, Machine has received new engine in 07/2022 Deutz BF6M1013ECP .Hydraulik pump is refurbished. Machine is dry , everything works. First hand owner maintained . All service available Dwedpeufibqofx Addef

Condition: new, Year of construction: 2025, machine/vehicle number: 145568556, Gasparin jaw crusher GI129C Everest mobile jaw crusher on crawler track 55 ton machine with extremely robust crusher and exceedingly high potential. It is characterized by the robust construction in all its parts and is certainly the best answer to the most heaviest applications. Equipped with Grizzly vibratory feeder (GI129C), it is suitable for more traditional applications, with Vibratory feeder and pre-screen, on the other hand, the machine (GI129CV) is suitable for arduous operations with high fines content and high material moisture. Djdpehd Na Hsfx Addewf Equipped as standard with the patented HCS system (Hydraulic Crushing System), EVEREST is the best answer to quarry requirements. Production capacity: approx. 400 TO/H Patented HCS system Proportional distributor with \"Load Sensing \" for an optimization of the system and a reduction of fuel consumption by approx. 30%. gap hydraulically adjustable even during crushing operation fast blocking system with wedges and folding cylinders dust extraction system tank pump magnetic separator warranty 1 year up to max. operating hours from start of operation of the plant Technical data: Jaw crusher 1150 x 850 mm crushing gap from 75 to 200 mm feed hopper 7 m³ - 2850 x 4960 mm Grizzly feeder 1120 x 4250 mm Main conveyor belt 1100 x 10000 mm 4 cylinder constant speed diesel engine 82 HP/60 KW, exhaust stage V Control panel chain drive 500 x 3900 mm Weight: kg transport length 12950 mm Transport width:3000 mm Transport height 3400 mm More information Purpose: construction, General condition: very good, Technical condition: very good, Visual condition: very good,