Pre-shredder

HAAS Recycling Systems TYRON 2000 XL 2.0

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Cgjdpfxovgrh Uo Agkep Your service team Mertens & Frowein GmbH

Condition: good (used), Year of construction: 2009, functionality: fully functional, Weight 4950 kg, total weight 12000 kg Cgjdpfxewpmckj Agkep 5.5 kW

Condition: used, mileage: 10,500 km, power: 220 kW (299.12 HP), first registration: 07/2018, fuel type: diesel, overall weight: 26,000 kg, color: yellow, gearing type: mechanical, suspension: other, number of seats: 1, operating hours: 10,500 h, Equipment: ABS, air conditioning, all wheel drive, cabin, trailer coupling, Air seat, reversing alarm, 1st hand, spare wheel, reversing camera, seat heating, radio, diesel Year of construction 2018 All-wheel drive 10,500 operating hours Cabin Trailer coupling Air conditioning 20 km/h ABS Headlights front and rear 1 seat LockUp/OptiShift Rotating beacon Heated air seat Reversing alarm Reversing camera Radio Diesel particulate filter Shovel with cutting edge Scales Rear weight BSS central lubrication Additional counterweight Spare wheel with rim Tires 26.5 R25 Michelin 80 Service at Volvo (Bischoff) deposited Gross vehicle weight 26,000 kg 1st hand FOR US THE CONDITION AND THE FEEL OF THE CONSTRUCTION IS DECISIVE, THE PRICE TAKES SECOND PLACE If you have any further questions, please do not hesitate to contact Mr. Faller on the number. //*EXCHANGE, TRADE-IN OR LOAN OF YOUR VEHICLE, AS WELL AS FINANCING POSSIBLE! All information without guarantee* Further offers can be found on our homepage: The description and data given do not constitute a guarantee and are not binding. The purchase contract concluded at the dealership when the vehicle is purchased is binding. Subject to errors and prior sale! Codpfjvithhox Agksgp

Condition: good (used), Machinery from honey processing factory. DC Norris hotrooms, DC Norris settling tanks, DC Norris holding tanks, crystallised tanks, super seed tanks, pump, filter sets, various filling lines to fill squeezy bottles, glass jars and plastic buckets. Cgjdpfepcibmsx Agkjp

Year of construction: 2023, condition: new, Chopping height max. mm. 200 Infeed width mm. 500 Infeed rollers piece 3 Rotor flight circle mm. 600 Chopping length approx. mm. 20-30 output - output 16 - 20 rm/h chipping Chipper blade piece 2 Feed motors kW 2x2,2 Cgsdpjncd Azofx Agksp Weight approx. net kg 4100 Inlet : horizontal machine base : steel, inert gas welded Rotor : steel, inert gas welded, dyn. balanced. Bearing : Oversized roller bearings. Bearing housing : Steel, flanged housing. Feed rollers : steel, special toothed. Chip outlet : underneath the machine. Machine grate : (sieve) for secondary crushing of excess lengths. Drive pulley : Matched to main motor N=1500 min-1 Hydraulic system : consisting of: Hydraulic pump, diaphragm accumulator, cylinder, pressure gauge, control valves for lifting of the upper feed roller. Feeding : by 2 gear motors, Make NORD GEAR

Condition: excellent (used), Year of construction: 2006, operating hours: 2,632 h, functionality: fully functional, machine/vehicle number: 29.381, pressing force: 35 t, filling opening width: 620 mm, filling opening length: 1,000 mm, total width: 2,380 mm, total height: 2,500 mm, total length: 6,625 mm, Including feed belt. The machine is immediately ready for operation. Codpfxjvaw T Aj Agkegp

Condition: ready for operation (used), Hsm HL 4809 LI baler - Large filling opening, ideal for big boxes - Container tipper for convenient filling Pressing force in kN: 480 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 400 kg - Bale dimensions (length x width x height in mm): 1200 x 1100 x 750 - Machine dimensions (length x width x height in mm): 5648 x 1849 x 2515 Codsra Dddjpfx Agksgp Idle cycle time in seconds: 53 - Manual tying: 4 times with wire

Condition: used, Year of construction: 2021, Lindner Urraco 95 DK – Year of Manufacture 2021 – Well-Maintained Condition For sale is a Lindner Urraco 95 DK from 2021 with 7,230 recorded operating hours. The shredder is in a well-maintained and ready-to-use condition. The exact condition can be seen in the photos. The machine is equipped with the DK4 package, featuring a reinforced gearbox and a reinforced cutting frame. — Specification / Scope of Delivery • 1 set of armoured shafts HW 8/10 with clearing combs and breaker bar, suitable for scrap and waste • 1 set of used shafts HW 8/10 with clearing combs and breaker bar, also for scrap and waste • DK4 package with reinforced gearbox and reinforced cutting frame — Technical Data – Lindner Urraco 95 DK Model: Lindner Urraco 95 DK Year of manufacture: 2021 Operating hours: 7,230 Cgedpfxox Nkhqj Agkep Engine power: approx. 566 kW (approx. 770 HP) Emissions standard: Stage V / Tier 4f (depending on version) Shaft length: approx. 2,500 mm Shaft diameter: approx. 870 mm Maximum torque: up to approx. 480,000 Nm Machine weight: approx. 46 t Dimensions (L x W x H): approx. 9.2 m x 2.55 m x 3.2 m Chassis: crawler tracks, hydraulically driven Application areas: scrap, commercial waste, bulky waste, mixed waste, wood, recycling material — Condition: Well-maintained machine Fully operational Sale as inspected on site Additional Information / Maintenance History The machine had a full maintenance and service contract directly with Lindner until recently. All maintenance and service work was carried out professionally in accordance with the manufacturer’s specifications and documented. Notes: • Sale is without any warranty or guarantee. • No return or renegotiation. • Subject to prior sale. All information provided is without obligation. The seller accepts no liability for possible errors, omissions, or changes in the details. Sale is exclusively subject to prior sale.

Condition: used, machine/vehicle number: 12625, Rotor diameter: 800 mm Rotor width: 1500 mm Cgsdpfx Ask Rfvksgksp 6-knife rotor 4 rows stator knives Inlet cross section approx. 820 x 1500 mm Drive motor: 160 kW

Condition: new, Hopper opening: 2.500 x 2.000 mm Rotors: 2 pcs. Rotor flight circle: 580 mm each Rotor design: 5 and 6 cutting teeth Codpfx Aobq St Hjgkegp Drive: 2 x 90 kW with planetary gears Hydraulic screen flap interlock for the discharge of contaminants Weight: approx. 18.500 kg