Used Baler for sale (280)

Condition: good (used), functionality: fully functional, machine/vehicle number: 004, bale weight: 5 kg, power: 3 kW (4.08 HP), empty load weight: 130 kg, Used THERMOPERS, model TO6 the compact plastic waste baler for soft thermoplastics, such as wrapping and shrink films, and to process it into bales. Serial number 004. Kedper Dufbofx Adwjdg The Thermopers is the solution to handle the plastic waste stream efficiently. The material can be loaded into the Thermopers directly. When the Thermopers is full it can be closed and started, the rest of the process is fully automatic and silent. The inserted material is compressed and sealed into an easy-to-handle package of approximately 5 kg. Characteristics The volume of the plastic films is reduced by 90% with the Thermopers. Thanks to the compact size of the Thermopers and the connection to a standard 230 Volt socket, the machine is easy to apply everywhere. The Thermopers is easy to operate and the status of the compaction process is clearly displayed by LED indication. The drive of the Thermopers is fully electric and low in maintenance. The size of a package is 60 x 30 x 10 cm and has a weight of approximately 5 kg. Operation The plastic waste material can easily be loaded into the machine via the insertion valve. When the machine is fully loaded, the insertion valve is closed and the machine is started. The plastic material is compressed by a combination of pressing and heating, whereby the outside of the plastic material is sealed around the package as a mantle. Thereafter the package is cooled, and the pressing mechanism will return. When ready, the machine gives an audio signal and the compacted package can be removed. After this the machine can be used again instantly. Advantages • Easy to operate • Fully automatic and silent • Compact machine • 90% volume reduction • Prevents drifting of material • Less storage • Less transport, resulting in a reduction in CO2 emissions • Higher returns / lower costs • Low maintenance • In accordance with machinery directive, CE marked Technical data Width: 70 cm Depth: 50 cm Height: 128 cm (excluding press rods) Height: 208 cm (including press rods) Weight: 130 kg Mains voltage: 230 Volts Power: 3 KW Energy consumption: approximately 1 kWh per package Sales price: 1.550 Euro + VAT, negotiable, FCA Oradea, Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: used, Year of construction: 2006, operating hours: 54,050 h, pressing force: 80 t, filling opening width: 1,020 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, oil tank capacity: 2,100 l, power: 94 kW (127.80 HP), empty load weight: 21,000 kg, Technical data baler: Manufacturer Paal Typ Konti 275 E Year of construction 2006 Hours of operation in total 54,050 hours Press power main press 80 tons at 300 bar Specific press capacity 9,7 kg/cm² Feed channel 1,600 x 1.020 mm (l x w) Throughput capacity under operating conditions 350 m³/hour Bale size 750 x 1,100 mm, length variable Driving motor 75 kW Connected load 94 kW Rated current 180 A Tying system 4-fold vertical, fully automatic Bale weight up to 750 kg, depends on material Volume hydraulic oil tank 2,100 l SPS controller (manuf., type) Siemens Simatic S7-300 Operating panel (manuf., type) Siemens Multi Panel Transport dimensions only baler 11,152 x 2,152 x 3,000 mm (l x w x h) Machine weight baler approx. 21 tons Condition of the baler: The press and conveyor belt are in satisfactory working condition, see photo documentation. Further technical data and dimensions for the conveyor belt are not currently available. The plant is currently still in operation and is to be replaced by a larger press plant in the coming months. Scope of delivery: Bale press, bale chute, conveyor belt and machine documentation. Kedpfjxcxm Eex Adwedg Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Dismantling and loading is the responsibility of the buyer. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2012, operating hours: 12,078 h, functionality: fully functional, pressing force: 88 t, filling opening width: 1,100 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 30,000 kg, oil tank capacity: 2,000 l, power: 98 kW (133.24 HP), volume flow: 643 m³/h, Technical data baler: Manufacturer HSM GmbH + Co. KG, Germany Type VK 8818 R-FU Year of construction 2012 Total operating hours: 12,078 hours, as of September 2025 Pump operating hours 6,616 hours (effective pump running time) Number of bales pressed: 65,792 bales, as of September 2025 Main press force 880 kN Specific pressing force 120 N/cm² Pressing force cutting edges free rammer 120 kN Dimensions of feed chute 970 x 1,800 mm Theoretical cycle time in idle mode 8.3 seconds Theoretical throughput capacity 643 m³/hour Bale dimensions 1,100 x 750 mm, the length is variable 600 up to 2000 mm Drive power 2 x 45 kW frequency-controlled Connected load 98 kW Total current consumption 192 A Fuse protection 250 A slow-blow 5-fold horizontal tying, fully automatic Throughput rates with a bulk density of 20 kg/cbm 12.86 t/hour Bulk weight of 50 kg/cbm 32.15 t/hour Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depends on materiel Hydraulic oil tank capacity 2000 litres PLC control Siemens S7-300 Ksdpfx Adsxcngnowjdg Siemens TP 700 control panel Press dimensions assembled 18,000 x 4,300 x 3.270 mm (l x w x h) Press dimensions with conveyor system 18,000 x 22,000 x 5,765 mm (l x w x h) Transport weight baler approx 30 t (Main press approx. 20 t, press channel with bale clamp approx. 10 t) Special machine equipment: Access locking by means of key transfer system Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials Additional optional equipment ordered: Frequency-controlled main drive, 2 x 45 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material Cutting-edge frei rammer with 121 kN pressing force Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end Bale chute Visual warning signal, mounted on the control cabinet Condition of the baler: The entire baling system (baler and conveyor belt) is in good, operational condition. Technical data for the chain belt conveyor: Manufacturer Stadler Anlagenbau GmbH Typ chain belt conveyor KF 1800 Year of construction 2012 Drive power 7.5 kW Belt speed 0.05 – 0.4 m/second Length of feeding conveyor 6,000 mm Height of side wall from feeding conveyor 400 mm Length of incline conveyor 9,000 mm Height of side wall from incline conveyor 800 mm Length of gooseneck 1,500 mm Incline 30° Nominal width 1,800 mm Useful width 1,700 mm Belt quality EP-500/4 Steel cleats on the rubber belt 50 x 50 mm Hollow pin chain, pitch 125 mm, rollers 36 mm Height of drive axle above ground 4,284 mm Overall height of conveyor belt 5,765 mm Transport dimensions of feeding conveyor approx. 7,000 x 2,200 x 1,250 mm (l x w x h) Transport dimensions of the incline conveyor 13,000 x 2,500 x 2,900 mm (l x w x h) Pit dimensions for the conveyor belt 14,765 x 3,260 x 1,250 (l x w x h) Scope of delivery: The conveyor belt, baling press with bale chute, and wire drawing stations are available for sale, but without the wire. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2008, operating hours: 23,000 h, machine/vehicle number: 00834, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,315 mm, bale width: 1,100 mm, bale height: 720 mm, warranty duration: 3 months, power: 30 kW (40.79 HP), year of last overhaul: 2025, Equipment: documentation/manual, Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler, hereby offers the following machine(s) A repaired HBC60 (30kw) Repaired – in very good technical condition Year of construction: 2008 Kedjxck U Uepfx Adwjdg Volume capacity m3/hr max. 365 334 321 301 Volume weight kg/m3 max. 15 30 50 80 Weight capacity T/hr max. 5.5 10 16 24 Bale weight 400 – 800 kg, depending on S.G. of material and bale length Bale length - adjustable Bale height - 720 mm Bale width - 1100 m Filling opening - 1100 mm x 1320 mm Max. size supply - 1500 mm x 1200 mm Pressure force ram - max 60 tonf. Pressure force pre-press flap - max 25 tonnes Cycle time - 18 seconds Motor - 45 kW Motor Twistomat - 2.2 kW Motor counter pressure pump - 1.1 kW Following repairs have been done in our official Bollegraaf OEM Refurbishment Workshop: * Safety doors needle installation replaced with new * Ram wheels behind replaced with new * Bronze strip above ram replaced with new * Movable beam position switch ram replaced with new * Scraper above ram replaced with new * Sealing pre press cylinders replaced with new * New steel beams channel cylinder * nieuwe buisjes oplassen en wielen gangbaar maken * New pusher cylinder underneath vertical tying unit * Safety hatch behind needle installation replaced with new * Several cables and asi modules replaced with new * New air filter * New oil filters

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Kdjdpfxjxbgnhj Adweg Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, HSM V-Press 605 waste paper baler - used The HSM baler is a compact device for reducing packaging waste by up to 95%. It is designed to compact and crush cardboard (paper sacks, waste paper, offcuts) and film (stretch film, plastic sacks). It enables them to be disposed of economically. The waste paper baler has a graphic text display informing of the machine's stage of operation and a large waste loading opening. All this contributes to the comfort of use of the baler and its easy intuitive operation. Advantages of the HSM V-Press 605 baler: - Compact size - contributes to space saving. - Crushing force of 57 kN (approx. 6 tonnes) - allows bales of up to 70 kg with dimensions of 80 x 60 x 60 cm to be formed. - Low noise level - 60.1 dB (A) - Material support claws - increases loading volume and therefore increases baling capacity. - Mechanical ejector - makes bale removal easier. - Large loading aperture - increases user comfort. - Quick and easy assembly. Kdodpfx Aowcpvajdwjg The offer concerns the HSM V-Press 605 waste paper baler: - Code produkt : MTP004168 - Product condition: used - Year of manufacture : 2018 - Model: V-Press 605 - Width: 119 cm - Depth: 81.5 cm - Height: 198 cm - Weight: 485 kg - Power: 1500 w - Voltage: 400 v Net price : €3499.00 each * I have large quantities, prices can be negotiated for larger orders. * Transport throughout Europe possible. * The above offer does not include transport costs. * Location: Chmielów/Tarnobrzeg, Poland.

Condition: excellent (used), Year of construction: 2006, Balemaster Kodpfx Aderdwlkewsdg Year: 2006 Type: CMG 268 Waste compactor

Condition: excellent (used), Year of construction: 1992, functionality: fully functional, pressing force: 4 t, bale length: 500 mm, bale width: 700 mm, bale height: 450 mm, bale weight: 50 kg, HSM 45 VL – Technical Data Kdodpfx Aswuk Nrodwog Feature Value Pressing force approx. 44 kN (4.5 tonnes) Motor power / Power supply 1.5 kW / 400 V, 50 Hz (CEE 16A) Idle cycle time approx. 23 seconds Throughput (theoretical) approx. 38 m³/h (3–6 bales/hour) Press chamber (W × D × H) 700 × 500 × 940 mm Feed opening (W × H) 700 × 600 mm Max. bale size (W × D × H) 700 × 500 × 450 mm Bale weight approx. 30–50 kg Machine dimensions (W × D × H) 840 × 720 × 2085 mm Feed height 500 mm Machine weight approx. 374 kg

Condition: good (used), Year of construction: 1996, Baler including conveyor, wire bins Manufacturer: Bollegraaf Typ: HBC 50A Build in: 1996 Baler weight: 19000 kg Weight conveyor: 6000 kg Engine: 30 kW Vertical binding Kdsdpfx Ajxtmyzsdweg Number of wires: 5

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: 413.00.003, pressing force: 60 t, bale weight: 400 kg, TECHNICAL DETAILS Pressing force: 60 t Main drive power: 9.0 kW Kdedpewhqf Tsfx Adweg Bales Bale dimensions (W x D x H): 1,100 x 1,100 x 800 mm Bale weight: max. 400 kg Binding: 4-fold vertical MACHINE DETAILS Machine dimensions (L x W x H): 6,500 x 1,850 x 2,800 mm Weight: approx. 8,000 kg Electrical system Operating voltage: 400 V Frequency: 50 Hz Total connected load: 28 kW Regular maintenance keeps the baler in good working order.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Kdodpfxou Thhrj Adwsg Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Kdodpfx Adjvwlqqowog Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), functionality: fully functional, Technical data for the document shredding system: Manufacturer HSM GmbH + Co KG General data for the two-stage shredder system: Type Duo Shredder 5750 Year of manufacture 2015 Operating hours 3,093 hours Throughput capacity up to 800 kg/hour, depending on material Rated power 30 kW Rated current 62 A Particle cutting size 6 x 40 - 53 mm Fuse protection 63 A gG/gL/C/K Weight of shredder approx. 2500 kg Data on the pre-shredder: Shredder type V 570 Working width of the cutting unit 500 mm Particle size 20 x 155 mm (w x l) Nominal power of pre-shredder 2 x 5.5 kW Nominal current of pre-shredder 2 x 11.5 A Kedpfewrybrex Adwedg Data on the secondary shredder: Shredder type P 500.2 Working width of the cutting unit 500 mm Particle size 6 x 40 – 53 mm (w x l) Nominal power of secondary shredder 9.2 kW Nominal current of secondary shredder 18 A Security level according to DIN 66399 P-3, O-2, T-3, E-2 Baling press data: Type KP 100.1 Year of manufacture 2015 Operating hours 2,377 hours Pressing force 9 - 12 t Bale weight 40 – 150 kg/bale, depending on material Cycle time 7–16 seconds Feed chute dimensions 450 x 580 mm Bale size 630 x 500 x 400-1000 mm (w x h x l) Triple horizontal binding Press dimensions 3990 x 2225 x 1735 mm (l x w x h) Weight of press approx. 1000 kg Dimensions of entire system, conveyor belt, shredder and press: 9560 x 2071 x 3550 mm (l x w x h) Function description: This is a complete system consisting of a feed conveyor belt, a two-stage shredder and a horizontal baling pres. The material is fed onto the conveyor belt, shredded in two stages and then pressed into stackable bales. A second cutting unit and various motors are available as spare parts for the system. Comments: The documentation (Manual, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2016, operating hours: 6,500 h, A scrap shear in very good condition is for sale. The machine can be inspected at any time. Kdjdpfx Asxnavxsdwjg

Condition: refurbished (used), Year of construction: 1999, functionality: fully functional, pressing force: 71 t, filling opening width: 1,080 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, total width: 3,450 mm, total height: 4,090 mm, total length: 10,020 mm, input voltage: 400 V, overall weight: 27,000 kg, noise level: 85 dB, pressure: 300 bar, transport height: 2,300 mm, power: 37 kW (50.31 HP), Fully automatic channel baler with pre-press flap available immediately. The machine includes a conveyor belt with a floor-mounted section. The baler is supplied in refurbished condition and the conveyor belt underwent a belt overhaul at the beginning of this year. The machine was taken out of production at the beginning of October and is currently stored in our facility. It can be demonstrated in operation at our location. This machine is particularly suitable for baling paper/cardboard and various types of plastics such as PET, HDPE, and big bags. Technical specifications baler: Drive: 37 kW Press force: 71 tons Bale dimensions: 1100 x 720 x 1300 mm (length adjustable) Number of wires: 4 vertical Kdedpfx Adexl Rqbowog Filling hopper dimensions: 1620 x 1080 mm Bale weight: up to 600 kg (depending on material) Capacity: up to 20 tons per hour (depending on material) Transport weight: 27,000 kg Technical specifications conveyor belt: Length of horizontal section: 3,000 mm Length of inclined section: 7,424 mm Angle: 29° Filling option: at floor level

Condition: excellent (used), Year of construction: 2006, operating hours: 2,632 h, functionality: fully functional, machine/vehicle number: 29.381, pressing force: 35 t, filling opening width: 620 mm, filling opening length: 1,000 mm, total width: 2,380 mm, total height: 2,500 mm, total length: 6,625 mm, Including feed belt. The machine is immediately ready for operation. Kdedpfovaw T Aex Adwog

Year of construction: 2008, condition: good (used), Horizontal baling press Kdjdpfjg Ibt Njx Adwsg Build in 2008 Bale size 800x1000x1400 Loading height 1250mm

Year of construction: 2025, condition: used, Packaging machines, consisting of: 1x Rotary arm wrapper with top sheet applicator, type: B200E, manufacturer: TechnoWrapp 1x Ring wrapper, type: A800-4, manufacturer: TechnoWrapp 1x Rotary arm wrapper, type: CW 400E, manufacturer: CombiPack Kodpfx Adewk Dv Djwodg 1x Baler, type: BVP-950-HL1, manufacturer: Willems, Indion Technical details, equipment, photos, and operating time are shown in the attached description.

Condition: new, functionality: fully functional, Year of construction: 2025, Pick-up: 2.25 meters. Adjustable cultivator roller and fixed, self-steering gauge wheels. Chopper with 17 knives. Channel bottom with suspension for improved material flow. PowerGrip packing rollers (18 units), axle with air brakes. Flotation tires 500/60-22.5. Net binder with holder for additional roll. Transmission: 540 RPM. Price: 47,900. Kdodpfxextatho Adwjg

Condition: reconditioned (used), Year of construction: 2012, functionality: fully functional, machine/vehicle number: PVM 324212-1, pressing force: 20 t, filling opening width: 1,200 mm, filling opening length: 480 mm, bale length: 1,200 mm, bale width: 800 mm, bale height: 1,200 mm, bale weight: 250 kg, total width: 1,030 mm, total height: 2,790 mm, total length: 1,775 mm, input voltage: 400 V, input current: 16 A, overall weight: 1,250 kg, warranty duration: 6 months, noise level: 64 dB, power: 4 kW (5.44 HP), BRAMIDAN vertical baler B 20 suitable for pressing cardboard and foil - very well preserved, overhauled in the workshop, new hydraulic hoses. UVV test according to DGUV rule 214-017 when delivered new. Kdsdpfxovm U Rlo Adwsg Price ex works Stutensee, own collection possible, alternatively shipping by freight forwarder in the cost statement

Condition: used, Year of construction: 1987, functionality: unexamined, machine/vehicle number: 6215.101.00001B, pressing force: 12 t, Our HSM 12 Gigant is in its element wherever bulky cardboard, plastic films, or other materials need to be compacted. Thanks to the extremely large loading opening, the device can be filled simply and conveniently. The result is compact bales that are easy to transport. And if the press is urgently needed in another area of the company – not a problem: Thanks to its 4 wheels, it can be used anywhere and at any time. Kdjdpfew Az E Tsx Adwsg

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, machine/vehicle number: 113889, pressing force: 60 t, filling opening width: 550 mm, filling opening length: 1,160 mm, bale length: 1,200 mm, bale width: 800 mm, bale height: 1,100 mm, bale weight: 420 kg, total width: 1,400 mm, total height: 2,170 mm, total length: 1,890 mm, type of input current: three-phase, input voltage: 400 V, overall weight: 2,430 kg, power: 7.5 kW (10.20 HP), year of last overhaul: 2025, Brand: Dixi The stated price is exclusive of statutory VAT, ex works and without packaging. The press is cleaned and function-tested. Technical details: Manufacturer: Dixi Type: 60S Kjdpfjwnpx Ejx Adwjdg Bale format (LxWxH): 1200 x 800 x 1100 mm Bale weight: 340-500 kg External dimensions (LxWxH): 1890 x 1400 x 2170 mm Filling opening: 1160 x 550 mm Pressing force: 600 kN Throughput: 1 - 2 bales/hour Number of wire channels: 4 Weight of the press: 2,430 kg Power supply: 400 V / 50 Hz Power consumption: 7.5 kW Installation location: indoors / outdoors under cover Serial number: 113889 Year of construction: 2012 We point out the respective original documentation, which can be obtained directly from the manufacturer.

Condition: reconditioned (used), Year of construction: 2020, pressing force: 50 t, filling opening width: 670 mm, filling opening length: 1,200 mm, bale length: 1,200 mm, bale weight: 450 kg, total width: 800 mm, total height: 800 mm, power: 7.5 kW (10.20 HP), empty load weight: 2,180 kg, input frequency: 50 Hz, Tested and ready for operation, Vertical baler Dixi 50S PET Year of manufacture: 2020 Kdjdpfx Aswviz Nodwjg Bale dimensions (L x W x H, mm): 1200 x 800 x 800 - 1100 Bale weight (kg): approx. 350-500 kg Specifications (L x W x H, mm): 1600 x 1300 x 3100 Loading opening (mm): 1200 x 670 Pressing force: 50 tons Power supply: 400 Volt Press immediately ready for use Net price plus VAT Delivery available at extra charge.

Condition: reconditioned (used), Horizontal Press Baler DIXI 60 SLD Year of manufacture: 2014 Semi-automatic 60-ton baling system for economical volume reduction of residual materials (recyclables) in industry and trade: Cardboard boxes Tetra packaging Foils PET bottles Foam Kjdpsnfux Usfx Adwsdg Insulation boards and other compressible materials. Machine dimensions L x H x W approx. mm: 4150 (5080) x 1725 x 2035 Feed opening W x H (standard) mm: 990 x 1110 Machine weight approx. kg: 5420 Pressing force max. kN: 60 t / 600 kN Ironing cycle (average value) approx. s: 47 Bale size W x H x L approx. mm: 800 x 1100 x 1200 Bale weight (depending on material) approx. kg: 370-410 Binding: manual Number of bindings: 3, with wire with quick release eyelets Drive power: 7.5 kW; 400V/32A The presses are tested and functional and are offered with a fresh UVV and inspection in accordance with DGUV regulation 3. The Dixi 60SLD is ready for immediate use. On request, the Dixi 60 SLD can be completely overhauled for an additional charge. This includes: Replace all hydraulic hoses. Change the hydraulic oil and check the hydraulic unit. The hydraulic cylinders are checked and replaced if necessary. Net price plus VAT and possible transportation.

Condition: reconditioned (used), power: 11 kW (14.96 HP), operation weight: 8,000 kg, Horizontal baler DIXI 80 SLD 2018-2021 Year of construction Semi-automatic 80-tonne baling system for the economical volume reduction of residual materials (recyclables) in industry and trade: Cardboard packaging Tetra packaging Films PET bottles Foam Insulation boards and other compressible materials. Machine dimensions L x H x W approx. mm: 4,320 x 1830 x 2,154 mm Filling opening W x H (standard) mm: 1,040 x 1,110 mm Machine weight approx. kg: 8,000 Press force max. kN: 80 t / 800 kN Ironing cycle (average value) approx. s: 35 Bale size W x H x L approx. mm: 1,120 x 1,120 x 1,200 Bale weight (depending on material) approx. kg: 550 - 650 Kedpfx Ajqa Dq Dodwodg Binding: manual Number of bindings: 4, with wire with Quicklink wire Drive power: 11 kW; 400V/32A The presses are tested and functional and are offered with a fresh UVV and inspection in accordance with DGUV regulation 3. The Dixi 60SLD is ready for immediate use. On request, the Dixi 60 SLD can be completely overhauled for an additional charge. This includes: Replace all hydraulic hoses. Change the hydraulic oil and check the hydraulic unit. The hydraulic cylinders are checked and replaced if necessary. Net price plus VAT and possible transportation. The operating instructions are available and are supplied as a PDF file and in paper form.