Crank shaft replaced in 2018. Complete with electrical system and hydraulic power unit.
TYPE CADDY 80
Y.O.M. 2005
SERIAL NUMBER 28336
RPM CRANK SHAFT 63n/min
RPM FLYWHEEL 495 n/min
STROKE 70 mm
CUTTING CAPACITY 80 MM
Brf9zcaa0h
ENGINE POWER 45Kw 400Volts
Billet shears of Peddinghaus 214/1000
Built in 1972
good condition, the machine receives a technical review with minor deficiencies in our work.
Facilities
Length stop spindle adjustable in special design with drive
Rotary spline coupling
Grease central lubrication
Tpnpwdllm
PCs 2 feed system consisting of transport roller conveyor for 6 m bars, suitable for round and square materials.
TYPE 560
CUTTING PRESSURE 560 t
STROKES 40 n°/min
STROKE 90 mm
KNIVES LENGTH - 450 mm
SQUARED WORKPIECE SECTION - 85 x 125 mm
ROUND WORKPIECE SECTION - 90 -135 mm
FLAT WORKPIECE SECTION - 250 x 36 - 60 mm
- 400 x 35 - 55 mm
Gj8zccdv
MOTOR'S POWER - 30 kW
MAX. TOTAL WEIGHT - 18.000 Kg
BAR FEEDER - 4 KW
The machine has been fully overhauled. It comes with a bar magazine and bar feeder system.
New pinion gear, new flywheel shaft bearings, new flywheel bearings, new eccentric shaft bearing bras...
Billet shears 214/1000
10,000 of kN shear force
B0ainvmn
Built in 1973
with technical review with minor deficiencies
Transport roller with 2 height-adjustable supports
Material support table MAT 140-6 to the transport of Rod material in the roller conveyor
Used Peddinghaus Cadax 800 billet shears
Built in 1979
Shear force 8000 k N
Control electric
Length stop 500 mm
Pneum.. The clutch / brake combined unit
Yznuaojbo
Hydro of pneumatic clamps
Blade installation tool
Material slide, with 1 box
Section steel shears, profile shears, punch, punching machine, hole punch
-Pressure force: 35 to
-Punching:
-Scissors:
-to cut:
-not:
-mechanical release:
-div. Punches and dies:
Bnmgygzlf9
-Length stop:
-Installation dimensions: 1300/1570/H1900 mm
-Transport dimensions: 1300/770/H1900 mm
-Weight: 1112 kg
Cutting length 1050 mm Max. thickness 2 mm Mechanical
Equipped with: Manual back gauge 2 pcs. table extension arms Angel arm
B3usmul
1 used motorized plate shear
make Schröder
type MHSU 2000 x 3 mm
technical data:
cutting length
max. sheet thickness 3 mm
Bxdvar22tg
stroke rate 34 strokes/min
cutting angle 2 degrees
Drive power 4 KW
weight approx.1,5 to
dimensions 2400 x 1800 x 1200 mm
equipped with:
controlled positioning backgauge
sheet holding up device
foot switch
Plate shears VS 3006
Producer: DURMA
YP: 2010
Control Durma ... DT-10
Max. Cutting length ... 3080mm
Max. Cutting thickness ... 6mm
Drive ... hydraulic
L x W x H ... 4100x3650x1950mm
Machine weight ... 7980kg
The machine is in good condition and can be tested under power.
Pjbqx
Hydraulic CNC - guillotine shear
Bxamzvwq7q
Fab. Durma Typ. SBT 3000 x 6mm
Very good condition, year 2015
Technical data:
Sheet thickness: 6 mm
cutting length: 3.100 mm
cutting angle: 1,5
throat: 50mm
stroke/min: 15
backgauge: 1.000 mm
length: 4100 mm
width: 2200 mm
height: 2.100 mm
Weight: 7.650 kg
NC preselection control D-Touch 7 with touch screen for backgauge, cutting length, number of pieces
central cutting gap adjustment mechanically
motorized backgauge up to 1,000 mm on recirculating bal...
Dimensions LxWxH: 2.73x2.16x1.28 m
drive power: 7.5 KW
Net weight: 2600 kg
max cutting length: 2050 mm
max. sheet thickness: 4 mm
Backgauge adjustment range: 750 mm
Iledtgw3w
TECHNICAL SPECIFICATIONS ting length 2050 mm et thickness at 400N / qmm 4.0 mm Backgauge adjustment range 750 mm Drive motor power 7.5 KW Dimensions LxWxH 2.73 x 2.16 x 1.28 m Weight 2600 kg The exact description with technical data with picture can be found in the attached PDF file
Table shear cutting knife, replacement knife for table shear, replacement cutting, cutting knife, shear knife
-for: guillotine shears
-Number: 2 pieces available
-Hole spacing: 25/52/136 mm, 45/100/136 mm
-Price: complete
-Dimensions: 1650/49/12 mm
Gvu00s
-Weight: 14 kg
Completely overhauled FICEP CADDY 80 for material (round) 80mm and (square) 75mm. The system was completely overhauled in 2018 by FICEP and has not been used since then. A new separation table and roller table were installed. All components have been renewed and checked, the machine is state-of-the-art.
Cutting capacity in kN: 4400
Bxbfa0y0cz
Total consumption in kW: 45
Stroke per minute: 63
Stroke in mm: 70
FOLDING BENCH technique Halver,
Your competent partner in matters of impact shears and folding benches
Bihkxb3hgr
We are your contact for high-quality sheet metal processing.
As a long-standing sales partner of the Polish manufacturer PROD-MASZ, we respond to the needs of our customers on site and see ourselves as an extended arm of production.
Appropriate machines can be demonstrated if required, along with competent advice and professional instruction.
We advise you individually - according to...
5-fold combined sectional steel shears and hole punching machine PEDDINGHAUS type 210 / 11
machine. No. FD 1830 Year of construction approx. 1970
Hole punching
capacity approx. 40 ton.
Punching capacity Ø 25 mm in 11 mm sheet metal
Ø 20 mm in 13 mm sheet metal
throat 300 mm
Steel bar shear:
Cutting capacity round Ø 32 mm
Square 30 x 30 mm
Flat steel shears:
Cutting capacity flat 120 x 13 mm
sheet metal up to 11 mm
blade length 220 mm
- shearing angle approx. 2
Sectional steel shear:
Sh...
Hydraulic guillotine shear
Fab. MEGOBAL Typ. GH 3006
Year 1990
Cpspwoza
Technical data
Make: MEGOBAL
Type: GH3006
Year of manufacture: 1990
sheet thickness: 6 mm
working length: 3000 mm
cutting angle: 1°30'
throat: 300mm
dimensions: approx. L 3,40 x W 2,20 plus support arms) x H 1,80 m
Weight: approx. 6 t
Equipment:
- Motorized backgauge 10 - 1000mm
- angular stop
- support arms
- Central cutting gap adjustment
- Cutting length limitation
All data without guarantee.
The machine is in a very good...
Guillotine shears STROJARNE PIESOK CNTA 3150/16A built in 1987 by the Czechoslovakian company Strojarne Piesok.
The CNTA 3150/16 guillotine has:
- electronic bumper distance setting
- electronic knife account setting (potentiometer)
- electronic setting of the gap between the knives (potentiometer)
- hydraulic drive (hydraulic cylinders ensure the feed of the beam with the upper knife)
Bfp8ni7sdw
- hydraulic sheet clamps
Technical parameters :
- cutting line length: 3150 mm
- thickness of cut ...
Table shear cutting knife, replacement knife for table shear, replacement cutting, cutting knife, shear knife
-Spare knife: for guillotine shears, from stock for guillotine shears Fischer DHS 12/3000
-Quantity: 4 pieces available
Uurpdoon
-Lengths: 2x 2650/100/25 mm / 2x 450/100/25 mm
-Hole spacing: 200/250 mm, see photos
-Accessories: incl. Box with fastening screws
-Price: complete
-Weight: 126 kg
Catalog No. : 5463
Type: ATF 2023
Producer: AMADA
Made in: 1993, GO 2011
Characteristic:
Maximum cutting thickness: 2.3 mm
Minimum cutting thickness of the sheet metal: 0.4 mm
Maximum width of the sheet metal: 450-2000 mm
Maximum length of the sheet metal: 900-2450 mm
Max. length of cutting: 65-1250 mm
Zdbtcsg
Main motor output: 5.5 kW
Equipment:
Automatic sheet metal feeding using vacuum suction cups
Automatic storage of final sheets in a pallet
Automatic driven output conveyor
Motivated by the success of the past years, the Prod-Masz team will continue to make every effort in the future to maintain and further expand the leading position on the market through innovations.
The guillotine shear offered by us is designed for cutting non-hardened thin sheet metal in the range of sheet thickness up to 1.25 mm and max. cutting width 2500 mm. This universal machine tool can be used both in industry and handicraft.
The guillotine is manufactured in the technology of CNC, whic...
Shear blade, guillotine shear blade
suitable for guillotine shear MHSU 1000 / 4 (series approx. year 1991)
Type: MHSU 1000 Quality VA
part-no.: 121 193 02
The knives are new and unused
length: 1050 mm
upper knife height: 58 mm
Upper knife thickness: 12.0 mm
Bottom knife height: 58.0 mm
Bottom knife thickness: 12.0 mm
Hole spacing 115 mm
Knife with internal thread: M12
one-piece lower knife with slanted cutting edges
one-piece upper knife with slanted cutting edges
of a plate shear MHSU 1000 / 4
...
Parts shown by hand not come.
Gxrt8k
Immediately available from site :
Hydraulic guillotine shear Lotze
Type 203
Bxfxzmkn2i
Year of manufacture 1995
Cutting length 3040 mm
Material thickness 13 mm
Automatic cutting angle adjustment
Electronic positioning control Cybelec DNC 10
Digital display
Cutting gap adjustment manual, infinitely variable via central adjustment with digital display
Motorized back gauge, stop depth 10 - 2000 mm
Strokes / min 7 - 31
Lateral table ruler
Table extension from knife
Cutting line lighting
3 light barr...
Hand guillotine shears, guillotine shears, sheet metal shears, sheet metal shears, folding machine, edging bench
Bebaxwyqa7
-Hand guillotine shears combined with: folding machine
-Cutting width: 610 mm
-Max. Section thickness: 1.0 mm
-Swivel bending machine
-Max. Working width: 610 mm
-Max. Sheet thickness: 1.0 mm
-Transport dimensions: 845/910/H1230 mm
-Weight: 240 kg
- 1 set of spare blades
- complete documentation
max. Sheet thickness: 4mm
Cutting length: 2030mm
Stroke rate/min: 55
Table height: 750mm
stand projection: 200mm
Bxfqh9saz8
Cutting capacity for steel sheets up to 500N/mm2
Main drive motor: 15kW
motorized backgauge
operation via foot switch
external dimensions:
L: 2615mm
D: 2405mm
H: 1800mm
Can be tested on site under power.
Free truck
Weight: approx. 4500Kg
This is a Russian guillotine shear.
It is electro-hydraulic and is also controlled by compressed air.
Therefore, a compressed air connection is required for operation.
The cutting capacity is given with 6,3mm at a fatigue strength of 50kg/mm2. This corresponds to 490N/mm². We have cut 8mm mild steel S235 with it that also worked.
Brwzijbjrw
It has a manually operated back gauge and weighs approx. 4.4t with accessories. It can be loaded by us.
The machine worked until dismantling.
Hydraulic guillotine shears STEINER type HTS 30/20 R
machine No. 315 Year of construction 1982
cutting length 3050 mm
Cutting thickness 20 mm
Backgauge 800 mm controlled
Engine power approx. 30 kW
Power supply 400 Volt, 50 Hz
- Backgauge with positioning control ELGO
- Backgauge adjustment via ball screw spindles
- SICK front photoelectric safety switch as protection against intrusion
- 3 pieces Material support arms with ball rollers
- electric foot switch
- Replacement blades
Space requirement...
circle cutter as good as new, hardly used, max. cutting diameter 1.500mm, material thickness 1,5mm
incl. spare knives and knurling tools
Bw9uwdclit
electro-mechanical guillotine shear with motor-driven adjustable back gauge and
- ELGO-P 9521 electronic positioning control for adjusting the backgauge:
Displays: (LED version)
- Status displays for: + operating mode single step/program
- 6 segment displays for:
+ Actual value (6 digits, resolution 0.1 mm)
+ target value (6 digits, resolution 0.1 mm)
+ block no. (2 digits)
Bvyjfnzsgl
+ piece counter (3 digits)
+ Absolute/chain dimension preselection (1 digit)
+ keyboard
...
Section steel shears, profile shears, punch, punching machine, hole punch
-Pressure force: 80 ton.
-Punching projection: 500 mm
-scissors
-to cut
-Not tubes
Cynru7qg
-Tripping: electrical
-Foot switch: 2
-various punches and dies
-with: height adjustable roller conveyor
-Dimensions machine: 1000/2170/H2130 mm
-Weight machine: 4400 kg
-Dimensions roller conveyor: 2480/560/H700 mm
-Weight roller conveyor: 160 kg
Offer 21289
Combined flat and sectional steel shears with notching device and hole punching machine
Technical data:
- Flat steel shears - for flat material up to 200 x 13 mm.
- profile steel shear - L- steel at 90° 100 x 10 mm
- at 45° 70 x 7 mm
- Bar steel shears - round steel 36 mm
- square steel 30 mm
Mb0kn9o
- notching device - triangular notching 50 x 8 mm
- Hole punching machine - punching force approx. 550 KN
- stroke infinitely variable 0 - 60 mm
- punches in steel up to 20 m...
Hydraulic guillotine shear
Fab. HACO Typ. HSLX 3000x13mm
very good condition, year 1992
Technical data
Make: HACO
Type: HSLX 3013
year of construction: 1992
Sheet width: 3050 mm
sheet thickness: 13 mm
backgauge: 10-1000mm (can be folded up)
space requirement: approx. 4100 x 2300 x 2300mm
machine weight: approx. 10t
Equipment:
- Autom. cutting angle adjustment
- autom. cutting gap adjustment
Nlrmtp0
- controlled backgauge swivelling
- angle stop
- Light barrier for back clearance protection
- Swi...
ShearOne 15 electric guillotine shears - Made in Finland
Bwlchrxjdg
1500mm x 3mm
TC15 touchscreen control - sheet metal support - automatic cutting gap adjustment
pressure 300 t
square measurement . mm
diameter . mm
total power requirement 15 kW
weight of the machine ca. t
Bkobmdm20y
dimensions of the machine ca. m
Hydr. guillotine shears Impact shears Cutting shears
Manufacturer Atlantic
Model ATS 3006
Year of manufacture 1989
Jcfarmv
max. cutting length 3100 mm
max sheet thickness ST 40 6 mm
max. sheet thickness stainless steel 4 mm
max. sheet thickness aluminium 6 mm
distance between the uprights 3100 mm
backgauge motorized movable 0 - 750 mm
Cutting angle adjustment motorized
Strokes per min 14 pcs.
Hold down 18 pieces
Motor power 7,5 kw
Machine weight approx. 4500 kg
space requirement: width 3800 mm...
Plate shears, sheet metal shears, sheet metal shears, hydraulic shears, hydraulic shears
-guillotine shears: hydraulic
-Cutting width: 2550 mm
Bgtfwan0kg
-Max. Cutting thickness: 10 mm
-Projection: 330 mm
-Year of construction: 1964
-Space requirement: 3320/2530/H1940 mm
-Transport dimensions: 3320/1510/H1940 mm
-Weight: 9100 kg
Offer 18474
Technical data:
- Flat steel shears cuts flat up to 100 x 18 mm
- blade length approx. 250 mm
- Profile steel shear cuts angles
Bw9rkz2b7l
- 90° up to 100 x 10 mm
- 45° up to 70 x 8 mm
- Bar steel shears cut round steel 90° up to 36 mm
- square steel 90° up to 30 mm
- Notching device sheets up to 8 mm
- Hole punching machine - pressure capacity approx. 50 t
- throat 350 mm
- punches in steel up to 20 mm Ø in 15 mm
- drive 400 V / 3 kW
- space requirement approx. W 11...
guillotine shear, impact shear
Working width up to 2 meters
material thickness up to 3mm
good condition
Bjavsthu
(in use until 30.7.2021)
Hand lever shears VEB Scherenbau Nossen type ScDH10
blade length: 180 mm
sheet thickness: max. 10 mm
flat material: 50x15 mm
4-edge solid material: 22x22 mm
round steel: 24 mm
Angle steel: 60x7mm
T-steel: 60x7mm
on mobile base frame
Bwy70wml9v
own weight: approx. 150 kg
good condition
.
Ix0ukc3yy
cutting length 1000 mm
Cutting thickness 1-6 mm without problems and without adjustment of the cutting gap !
Throat 130 mm
.
Stroke rate 50/min
Drive power 4 kW
Weight estimated 3 to
.
Width approx. 2.3 m
Depth without arms approx. 1.7 m
depth with arms approx. 2,4 m
.
Hold-down device with rubber pressure pieces
Backgauge manual 500 mm
side stop 1200 mm
.
.....
Hydraulic guillotine shear
Make Reinhardt Maschinenbau
type. RAS 85.30
year 1999
cutting length. 3150 cm
cutting height 4mm
Bw9vem0zkd
with electronic stop
Plate shears, plate shears, plate shears, crank plate shears, hydraulic shears, hydraulic shears
-Manufacturer: Kramer, mechanical guillotine shears/motorized guillotine shears
-Type: TM I 2000/2.25
-Cutting width: 2050 mm
-Max. Section thickness: 2.25 mm
-Projection: 110 mm
-Drive power: 4 kW
Btsms2fgju
-Year of construction: 1972
-Dimensions: 2040/2460/H1225 mm
-Transport dimensions: 725/2460/H1225 mm
-Weight: 2090 kg
Sell well preserved guillotine shears from Romi
-manufacturer Romi
-type 6,5 x 3000
-year of construction 1994
-Hydraulic drive
-Cutting width approx. 3100mm
-Max. Sheet thickness 6,5mm
-Elec. Backgauge up to approx. 1000mm
-Electrical cutting angle adjustment
-Manual cutting gap adjustment
-lighting for cutting line display
-length approx. 3,8m, width 2,1m, height 1,7m
-Weight approx. 5,5 t.
Shipping on request
Forklift for loading available
For the sale applies the differential taxation accord...
Scrap pressing shears Bonfiglioli Squalo 1300T
Diesel engine * IVECO
Power (hp) 177
Fuel consumption (l / h) 8-9
Hydraulics BOSCH REXROTH
Number of knives (pcs.) 4 (4 edges)
Chamber material Hardox 500
Bvu9xz2met
Machine dimensions (mm) 8340 х 2490 х 3600
Dimensions of the loading chamber (mm) 4300 (+1500) x2200
Weight (t) 47
Productivity (t / h) 5-10
The work cycle is automatic
Scrap output parameters (mm)
Width
PRAMAC LIFTER type HL 10 M hand operated hydraulic scissors pallet truck
Fabr. No. 118004 Year of construction 2002
Load capacity 1000 kg
Cgudgxlxu
Lifting height max. 810 mm
Overall height lowered 85 mm
fork length 1160 mm
- Made in Italy
- Telescopic hydraulic cylinder
- with single roller
Own weight 125 kg
good condition
burnt sectional steel shear as base model type MUBEA with power for
10 mm sheet steel,flat steel 100x11 mm, blade length 175 mm,
angle steel 80x8 mm,mitre 45 degrees 50x6 mm, T-STEEL 60x7 mm,
bar steel round 28 m and square 25 mm, square notcher for
plates up to 7 mm as well as 55x6 mm, punching tool 30 mm round in 5 mm,
stroke rate 36/min. on platform 440 kg, PRESENTABLE ! Furthermore pictures drilling + deburring units, galvanized bottom trap door approx. 850x850 mm !
Bt708zeos9
Here it con...
This high-quality punching machine / profile steel shear from the brand manufacturer Peddinghaus is a punching machine with versatile applications and maximum precision for the workshop, as well as the company. The Peddimaster 28 / 40 H has a punching force of 28 tons (280 kN) and is operated via the two foot pedals.
Highlights at a glance:
- High punching force of 28 t (280 kN)
- Versatile application possibilities
- High production output with maximum precision
- Fast, trouble-free tool change...
Wiefelstede, Germany
