Used Biomass Pellet for sale (344)

Condition: used, Revolving briquetting press RUF type RBK 55/2500/120 S Hydraulic pellet press or briquetting press for grinding sludge, metal chips, or similar No. 70002 Year of construction 2009 Briquette diameter 120 mm Briquette length in the pre-compactor approx. 120 mm Pressing force in the pre-compactor 30 tons at 260 bar Gbedpohg Uz Isfx Ah Hsg Briquette length in the main compactor approx. 80 mm Pressing force of the main press cylinder 250 tons at 260 bar Stroke size of the main press cylinder 120 mm Pressing force of the counter-press cylinder 250 tons at 260 bar Stroke size of the counterpress cylinder 15 mm Piston diameter of the main press cylinder 350 mm Press stroke Cycle time approx. 30 sec. for grinding sludge with low residual oil content Hopper size of the screw conveyor 1000 x 600 mm Hydraulic motor power 37 kW Mains connection 400 Volt, 50 Hz, 45 kW - Revolver with 5 stations for high material throughput - Pre-compressor stage for pressing material into the turret disk - 2 opposing main press cylinders with 120 mm and 15 mm stroke - Ejection cylinder for ejecting the finished briquettes from the turret disk - Infinitely variable adjustment of the hydraulic speed for each pressing stage - was used for grinding sludge from metal processing - Material hopper as hopper with screw conveyor - the machine was completely overhauled at RUF in 2018 - a new SIEMENS Simatic touch panel was installed in 2020 - only a few operating hours after the overhaul very good condition Grinding sludge recycling - great savings through cooling lubricant recovery - Large savings in disposal costs due to the reduction in volume and weight of the grinding sludge - Grinding sludge briquettes with a low residual oil content can possibly be classified as "non-hazardous waste".

Condition: used, Year of construction: 2002, machine/vehicle number: 910060/0001, conveyor dryer plant Factory consists of: Conveyor dryer: • Feed conveyor (2019) • Three horizontal chain driven conveyor levels made of 5 sections (2002); • 5 heat exchangers (2002); • 5 fans (each is 80kW) (2002); • Cartridge filter for poisonous particles (2002), filters are cleaned; Gbjdpfx Asvt Rmvsh Heg • Biomass separator (2019); • electronics; Fit to dry wood chips, corn biomass, hemp biomass. lucerne and similar. Manufactured in Germany

Condition: new, Year of construction: 2026, your benefits Sturdy press mechanism with low-wear, chrome-plated tongs Pressing chamber wear bush Pre-compressor with end-position-sensed cylinder and screwed cover Control box with SPS-control Screw channel with discharge screw Separate oil tank with pump motor and valve control Safety switch for oil temperature Mounting on stable base frame with rubber feet Gedpfx Ahocnz U Ej Hjbg Briquette quantity monitoring Robust construction, low-maintenance technology, little space requirement: The machines of the C-series are particularly suitable for small and medium-size enterprises, whose required throughput does not exceed 50-80 kg/h or 200 to 400 kg/day. Practically any suitable material can be briquetted, e.g. wood, polystyrene, foam, paper or biomass. All machines are available as left- or right-hand version. The mounting on a stable base frame ensures a quick installation and makes mobile use possible. Briquette diameter (mm) 50 Throughput capacity up to (kg/h) 50 (depending on material) Hydraulic motor (kW) 5,5o Screw motor (kW) 0,55 Oil quantity (litres) 100 Weight (kg approx.) 800 Outstanding features at a glance Hydraulics with separate oil tank: temperature-controlled hydraulic unit, complete valve control, pump motor for long running times Briquette length monitoring: regulates the length of the briquette to a constant level Pressing area wear bush: Prevents wear in the pressing area Location: Ex works - free loading

Condition: new, New and used briquetting presses. Do you need a briquette press? Contact us. We have many years of experience in machines for briquetting materials such as wood, biomass, paper and much more. We have more than 20 years of experience. Gjdpfox S Ii Rex Ah Hjbg Presses for round or rectangular briquettes. We ship alle over EU. Capacity from 20 to 400 kg. per hour.

Year of construction: 2026, condition: new, Screening machine | Oscillating screen type ASM-550 Demonstration machine - Make: S&F GmbH - Type: ASM-550 - Screening capacity: approx. 60 - 70 m³/h (for wood chips and sawdust) - Screening area: 5.4 m² - Fractions: 3 or 4 pieces - Screen decks: 3 pieces - Drive power: 4.0 kW - Machine weight: approx. 3,800 kg - Machine colour: RAL 6011 Reseda green - Screen inserts and material outlet freely selectable Suitable for screening the following bulk materials, among others: - Wood chips and wood shavings - Sawdust and sawdust - biomass - Wood pellets Gbodpjxtfv Iofx Ah Hog - charcoal - Waste wood - Bark Vibrating screen | Wood chip screen | Vibrating screen machine | Flat screen | Vibrating screen | Roll sifter | Screening machine for wood chips

Year of construction: 2025, condition: new, Stock No. 2846 Compounding Extruder Type Alphatec AD-.S 75 with: Segmented screws, co-rotating, intermeshing screw design Godpfxod Hqa Ie Ah Hjbg Cylinder water/medium cooled/temperature-controlled Throughput up to 1200 kg/h - material-dependent Drive 250 kW - AC 48 L/D R+W safety gear coupling 3x degassing zones, 1x vacuum pump with condensate separator 2x side feeders type ZS-B Siemens Touch HMI control OPTIONAL: > Melt filter/screen changer > pelletizing systems: ST strand, WRG water ring, or UWG underwater pelletizing > Screw configuration according to your requirements > Material dosing/blending : volumetric or gravimetric > Additional accessories Visit us at our Wuppertal plant. The system is ready for demonstration, test run date with your material after arrangement

Year of construction: 2020, operating hours: 7,000 h, condition: good (used), functionality: fully functional, 🔹 General Machine Data Machine type: Pyrolysis plant / Carbonization plant / Biochar production plant Manufacturer: PYREG GmbH Model / Type: PYREG®-P500 Design: Containerized (modular) Condition: Used Year of manufacture: 2020 Operating hours: 7,000 Availability: Immediately / by arrangement Location: Germany 🔹 Main Technical Data Plant type: Continuous pyrolysis / carbonization Reactors: 2 × PYREG reactor Input materials: - Wood - Landscape maintenance material - Biomass (material dependent) Process: Gbjdpfx Aex Rpxkjh Hsg - Thermochemical carbonization - Exhaust gas recirculation (EGR) - Autothermal operation 🔹 Containers & Dimensions Plant container: Dimensions: 9,000 × 3,000 × 2,800 mm Weight: approx. 14 t Exhaust gas equipment container: Dimensions: 3,000 × 3,000 × 2,800 mm Weight: approx. 4 t 🔹 Reactor Technology Number of reactors: 2 Reactor dimensions (each): approx. 3,500 × 790 × 790 mm Function: Heating and carbonization of the feedstock Discharge: Screw conveyor with rotary valve Burn-back prevention: provided 🔹 Combustion Chamber Function: Combustion of process gases Dimensions: approx. 2,400 × 2,000 × 2,450 mm (including support frame) Weight: approx. 4,000 kg Burner: FLOX® burner Ignition: Pilot/ignition burner 🔹 Exhaust Gas & Heat Technology Heat exchangers: - High-temperature heat exchanger: Tube heat exchanger (max. 3 bar, approx. 1.1 m²), Ceramic heat exchanger (max. 3 bar) - Stainless steel plate heat exchanger: Max. operating pressure 30 bar, Exchange area approx. 5.51 m² Exhaust gas routing - Exhaust gas recirculation (EGR): available - Exhaust gas piping: Stainless steel DN200 PN10 - Exhaust outlet: approx. 6,000 mm above foundation 🔹 Conveying & Discharge Technology Feed hopper: - Volume approx. 2 m³ - Filling opening: 1,900 × 1,600 mm - Feeding: Walking floor & rotary valve Char / mineral discharge: - Conditioning screw - Water-cooled discharge - Airtight discharge 🔹 Fans & Electrical Equipment Exhaust fans: - 2 units (3.0 kW and 7.5 kW) Exhaust gas recirculation fan: - incl. Siemens frequency converter, 3.0 kW Combustion air fan: - incl. Siemens frequency converter, 3.0 kW 🔹 Control & Automation PLC: Siemens S7-300 Operator panel: Siemens TP1200 Comfort Control cabinet: - Dimensions: approx. 2,200 × 1,200 × 550 mm Degree of automation: Fully automatic 🔹 Peripheral Equipment (included) - Bruns walking floor container - Dosing bin approx. 30 m³ - Vertical screw conveyor - Cover - Control system 🔹 Permits & Operation BImSchV-compliant: Yes (plant-specific) Containerized: Yes Transportable: Yes

Year of construction: 2013, condition: new, wood baking oven with direct heating Gbedpfx Aoygm Ueh Hjg baking area 1,0 x 0,7 x 0,25 m (L x W xH) 8cm heatingstones also available with fully automatic pelletfiring system

Condition: new, Year of construction: 2026, Weima Briquetting Press TH 714 The TH 714 machines are designed for plants with required throughput rates of up to 150 kg/h. The stable press housing enables the production of high-strength briquettes - from materials such as wood, polystyrene, foams, light metals, paper or biomass. Numerous additional options can be implemented, e.g. oil cooling for multi-shift operation. All machines are available as left- or right-hand version. Mounting on a stable base frame ensures fast installation and makes mobile use possible. User-friendly operation thanks to Siemens PLC control In order to live up to our performance promise, we design and produce all control cabinets ourselves at our Ilsfeld site and equip them with well-known international components. This guarantees highest quality with compact design. The used PLC-control from Siemens is perfectly adapted to the requirements of the briquetting process. Impurity-resistant screw conveyor due to cardanic suspension The screw conveyor, which transports the material into the pre-compressor of the briquetting press, is suspended on a cardan joint. This prevents interfering materials from causing damage to the screw conveyor. As is so often the case, however, it always depends on the specific application which suspension is chosen. For metal applications, for example, we often recommend rigidly mounted screws. Briquette diameter (mm): 70 Throughput capacity up to (kg/h): 150*1 Hydraulic motor (kW): 11 Oil quantity (liters): 250 Weight (approx. kg): 1100 Gbodpfx Ahjil Hggs Hog Location: Ex stock 54634 Bitburg - immediately available - subject to prior sale

Year of construction: 1999, condition: excellent (used), We are offering a Heizbosch natural gas boiler. Type LLR 4000 Gbsdjxxa Ivepfx Ah Hjg Boiler with a 4 MW output Year of manufacture: 1999 Flow temperature: max. 120 °C, Pressure: max. 6 bar Water capacity 5720 l It has only been used very rarely, primarily for cleaning two adjacent biomass boilers. Available from the end of March 2026

Condition: new, Year of construction: 2026, Make: S&F GmbH Type: MFB-500/5 Belt width: 500 mm Centre distance (A-A): 5,000 mm Conveying capacity: approx. 30 - 40 m³/h (at 0 ° incline) Drive: worm gear motor Motor power: 1.5 kW, 400 V, 50 Hz Belt speed: approx. 1.1 m/s Drive drum: Drum diameter 220 mm Tensioning drum: Drum diameter 220 mm with spindle tensioning station Belt: EP 250/2 2:1 rubber inclined conveyor belt with V-profile (15 mm) Machine weight: approx. 450 kg Machine colour: RAL 6009 Fir green Gedsw Ad Rrspfx Ah Hsbg Suitable for the following bulk materials, among others: Wood chips, sawdust and sawdust, biomass, wood pellets, charcoal, waste wood, bark, soil, humus, recycling material, cross-cuts and much more. Accessories (optional): Feed hopper (filling hopper), inner belt scraper, chassis, tow bar, steel support, electrical installation (16 A plug-in switch) Troughed conveyor belt | troughed belt conveyor | conveyor belt | bulk material conveyor | belt conveyor | inclined conveyor belt

Year of construction: 2025, condition: new, functionality: fully functional, machine/vehicle number: 2846, Stock No. 2846 Compounding Extruder Type Alphatec AD-.S 75 with: Segmented screws, co-rotating, intermeshing screw design Cylinder water/medium cooled/temperature-controlled Throughput up to 1200 kg/h - material-dependent Drive 250 kW - AC 48 L/D R+W safety gear coupling 3x degassing zones, 1x vacuum pump with condensate separator 2x side feeders type ZS-B Siemens Touch HMI control OPTIONAL: > Melt filter/screen changer > pelletizing systems: ST strand, WRG water ring, or UWG underwater pelletizing Gbsdpji Dtbujfx Ah Hsg > Screw configuration according to your requirements > Material dosing/blending : volumetric or gravimetric > Additional accessories Visit us at our Wuppertal plant. The system is ready for demonstration, test run date with your material after arrangement

Condition: new, Year of construction: 2024, functionality: fully functional, Wood thermal modification kiln fully equipped for thermo wood production, included: 15 m high AISI 316L isolated double wall chimney, inlet/outlet piping, pressure valves, gages, air compressor, full wood pellet heating unit, Siemens control panel, timber loading/unloading platform, 2 sets of timber spacers. Timber volume 7...8 m3, depends on bord dimensions and length; Inner chamber for timber length up to 7,5 m, total kiln length 10 m; Gbedpfx Asvzub Hjh Heg Full thermal modification cycle time ~24 h from heating up to cooling down; Temperature can be set up to 230°C or more if needed; Required nominal grid power 25 A, can be used without grid with power generator; To produce 1 m3 thermally modified timber: 9...10 kWh + 55...60 kg wood pellets = 16...20 EUR without labor costs; Our wood thermo modification kilns can be made according to customers needed length from 3,6 to 9 m (from 3 to 9 m3 timber volume);

Year of construction: 2007, condition: good (used), Twence has had a biomass powerplant since 2007 called BEC. The BEC converts biomass into green electricity, enough to provide a town like Hengelo with electricity. To achieve the goal of supplying heat from this plant a conversion was finalized January 2018. Due to this Gedpfx Aol Hydijh Hjbg conversion they have been able to produce three times as much renewable energy from virtually the same amount of biomass as before the conversion. The conversion was made by changing out the steam turbine. The MAN MARC6 condensing steam turbine is unable to have a large amount of low-pressure steam continuously extracted and was therefore replaced. The MARC6 steam turbine has been decommissioned and preserved since January 2018. Openings in the roof can be used to remove the generator, gearbox and turbine from the building. The roof can be partially removed, creating a large enough opening for these elements to be lifted through. There is ample space for a crane in between the biomass powerplant and the waste-to-energy plant, if the steam pipe outside is removed. The turbine hall is equipped with a 16-ton overhead crane which can be used to lift specific parts from the Turbine-Generator set. Make MAN Turbo AG Type MARC6-C03 kW 21000,0 Year of manufacturing 2007 Nominal speed (1/min) 5955 Trip speed (1/min) 6550 Live steam pressure (bara) 66 Live steam temperature (°C) 460 Bleeding pressure 1 (bara) 23,5 Bleeding pressure 2 (bara) 3,3 Bleeding pressure 3 (bara) 0,96 Nom. Exhaust pressure (bara) 0,079

Year of construction: 2002, condition: excellent (used), functionality: fully functional, Twin-screw extruder Ref. No.: DE27695 Gsdpfx Aex Dip Tsh Hsbg Manufacturer: Leistritz Type: ZSE 40 HP Year of manufacture: 2002 Screw diameter: 2 x Ø 40.0 mm L/D: 40D Drive: 70 kW Details: co-rotating, segmented screws and barrel, 1 x segment for side feeding Options: pelletizing, dosing, side feeder Does this offer not meet your requirements? Please visit our website Plama Engineering or send us your detailed inquiry, we have suitable solutions for almost every budget.

Condition: used, Year of construction: 2011, functionality: unexamined, For sale: container with extraction augers. The container was used as a buffer in a straw pellet manufacturing facility. Container dimensions: Height: 7750 mm, Width: 2150 mm, Depth: 3140 mm, Rail height on container: 900 mm, Godpfxowy T R No Ah Hsbg Container capacity: approx. 40 m3, Discharge window size: 1000x350 mm 3 extraction augers, each 1.1 kW The container has been disassembled and is ready for transport. For more photos and details, please contact me. Machines available for inspection in Sępólno Krajeńskie, Kuyavian-Pomeranian Voivodeship, Poland.

Condition: new, Year of construction: 2026, Make: S&F GmbH Type: MFB-500/8 Belt width: 500 mm Centre distance (A-A): 8,000 mm Conveying capacity: approx. 30 - 40 m³/h (at 0 ° incline) Drive: Drum Motor Motor power: 2.2 kW, 400 V, 50 Hz Belt speed: approx. 1.25 m/s Drive drum: Drum diameter 220 mm Tensioning drum: Drum diameter 220 mm with spindle tensioning station Belt: EP 250/2 2:1 rubber inclined conveyor belt with V-profile (15 mm) Machine weight: approx. 800 kg Machine colour: RAL 6011 reseda green Suitable for the following bulk materials, among others: Potatoes, Wood chips, sawdust and sawdust, biomass, wood pellets, charcoal, waste wood, bark, soil, humus, recycling material, cross-cuts and much more. Accessories (optional): Gedpfx Aoxk Tg Neh Hebg Feed hopper (filling hopper), inner belt scraper, chassis, tow bar, steel support, electrical installation (16 A plug-in switch) Troughed conveyor belt | troughed belt conveyor | conveyor belt | bulk material conveyor | belt conveyor | inclined conveyor belt

Year of construction: 2025, condition: new, functionality: fully functional, machine/vehicle number: 2846, We offer, successfully since more than 12 years, installed in all over EU, our new compounding extruders/lines : e.g. Type Alphatec AD-.S 75 with: Segmented, Co-Rotating intermeshing, cylinder water / medium cooled Throughput performance up to 1000 kg/h - depending on the material Drive 132 kW - 250 kW L/D Ratio - according to processing needs Degassing zones - as desired Side feeder type ZS-B - as desired OPTIONAL: > Melt filter/screen changer > Pelletizing systems: strand ST- , water ring WRG or Underwaterpelletizing UWP Gjdpfxei Dtbij Ah Hebg > Screw configuration according to your needs > Material dosing: volumetric or gravimetric > further accessories Visit us at our Wuppertal plant. Trail-run with your material-mix possible, darte and details uopn request.

Year of construction: 2019, condition: excellent (used), functionality: fully functional, Fresenius Kabi Lovo Automated Cell Processing System PN: 6R4900 Condition: Used in excellent condition. Gsdpfxsq Avtgs Ah Hebg PROCESS FAST. MAXIMIZE CONTROL. Only Lovo delivers automated, functionally closed cell processing through spinning membrane filtration. Product Features: The Lovo Cell Processing System is a benchtop cell processor that automates labor-intensive tasks of washing and concentrating white blood cell products. Using spinning membrane technology, Lovo allows for non-pelletizing cell concentration and reduces the need for manual re-suspension. Additional Features: Processing volume range: 1 mL to 21 L Operator-defined processing parameters including levels of supernatant removal and final product volume. The LOVO system is for laboratory use only. Cells processed on this system are not intended for diagnostic purposes, for direct transfusion, or for use in the production of a therapeutic product(s) or vaccine(s) for clinical use, unless the user has obtained advanced regulatory clearance or approval from the appropriate regulatory agency. Cell types Fresh, cryo-preserved, and culture-expanded white blood cells, including, but not limited to, leukapheresis CD34+ cells, CAR T-cells, TILs, NK cells, and MSCs Volume range Source Up to 22 L Output* 50 mL – 50 L Wash-out range Up to 99.9999%* System components • 73 lb, 35.3” x 17.6” x 24.5” (W x D x H) benchtop instrument • Single-use processing kit with spinning membrane module We have two units in stock, both fully functional. Password need to be changed. Please check out our other listing as well.

Year of construction: 2026, condition: new, Oscillating screen ASM series S&F oscillating screens and horizontal screens are used in many areas of the wood processing industry (sawmills, pelleting plants). Screening machines of the "ASM" series screen wood chips, wood pellets, sawdust and sawdust, waste wood, biomass and many other sawmill by-products in dry and wet applications. The material-protecting, horizontal-circular screening movement of the inclined screen box ensures a high separation efficiency of the vibrating screen. One advantage of the screening machine is that long and fibrous particles glide diagonally to tangentially over the screening surface. This means that - in contrast to throw screens - no jamming or plugging grain occurs. Further advantages are the robust design, the high screening capacity and the long, low-maintenance running time of the screening machine. In addition to standard dimensions, the company also supplies the "ASM" series as a "customising solution" in a split design for existing plants. This makes it possible to use new screening machines in cramped and difficult-to-access spaces in existing plants or sawmills. Screening machines of the "ASM" series offer screen sizes from 0.5 to 15 m² (per screen deck) and are characterised by a high screening capacity (up to 350 m³/h - depending on the material). At a glance: - Ideal for: Wood chips, pellets, sawdust, biomass, bark, waste wood, substitute fuel. - Areas of application: Wood industry, recycling and waste disposal, animal feed - Screening area: 0.5 - 15 m² (30 m² as double deck) - Screening capacity (depending on material): up to 350 m³/h - Separation size: 0.1 - 150 mm (depending on size) - Drive power: 0.55 - 15.0 kW (depending on size) Advantages: - High screening capacity - High separation efficiency - No jamming and plugging - Low noise and low maintenance Gbsdpfx Aoin Ey Seh Hog - Flexible use - Individual production Do you need further information? Please contact us! We will be happy to advise you.

Condition: new, Year of construction: 2025, operating hours: 2,846 h, functionality: fully functional, machine/vehicle number: 2846, We offer, successfully since more than 12 years, installed in all over EU, our new compounding extruders/lines : e.g. Type Alphatec AD-.S 75 with: Screw diameter 73 mm Segmented, Co-Rotating intermeshing, cylinder water / medium cooled Throughput performance up to 1000 kg/h - depending on the material Drive 132 kW - 250 kW L/D Ratio - according to processing needs Gbedpfx Ahei Dtbqj Heg Degassing zones - as desired Side feeder type ZS-B - as desired OPTIONAL: > Melt filter/screen changer > Pelletizing systems: strand ST- , water ring WRG or Underwaterpelletizing UWP > Screw configuration according to your needs > Material dosing: volumetric or gravimetric > further accessories Visit us at our Wuppertal plant.

Year of construction: 2015, condition: as good as new (ex-display), machine/vehicle number: 2245, stock-No.:2245 1 used Lab Extrusion-pelletizing Batch line, condition like new, equipped with: Extruder single-screw AlphaTec type AE-S 25-30 single-screw Ø 25 mm – 30 L/D Extruder motor 3 kW- AC, screw speed range up to 130 rpm frequency controlled Gjdod Sg Hrspfx Ah Hjbg cylinder air cooled, elec. heating 2 x 3 kW 1x venting athm. port 1x manual screen-pack-changer Ø 42 mm 1x strand-die-head 1x water bath 1.000 x 150 mm 1x strand-pelletizer, intake width 30 mm, motor 1,1 kW – AC control board with PID, melt pressure, speed by frequency converter Trial-run shortly possible, date by appointment Mire extruders ex our machine-stock Wuppertal Germany available.

Condition: reconditioned (used), Stock - No.: 2553 1 used, partly overhauled and functionally tested Single-Screw Extruder, equipped with: Material hopper loader Extruder BATTENFELD Typ UNI-EX 1-75-25 B Screw - Ø 75 mm – 25 L/D, Cylinder Air-cooled Extruder-Motor 120 kW – DC ( overhauled ) Gjdjiyyndopfx Ah Hjbg Screw –speed up to 130 r.p.m. additional Temperature controllers for down-stream equipment Control-Board with melt-pressure sensor / Display. Inspectiuon visist / trial-run shortly by appointment in our workshop Wuppertal Germany possible. We can offer, installed to this extruder: > screen-pack-changer > pelletizing ( strand, hot-face or waterring ) > other equipment Send us your inquiry. More extruder and complete pelletizing lines ex our workshop Wuppertal, send us your inquiry or visit us, you´re welcome

Condition: reconditioned (used), Stock - No.: 2553 1 used, partly overhauled and functionally tested Single-Screw Extruder, equipped with: Gbodpfxoiyynws Ah Hsg Material hopper loader Extruder BATTENFELD Typ UNI-EX 1-75-25 B Screw - Ø 75 mm – 25 L/D, Cylinder Air-cooled Extruder-Motor 120 kW – DC ( overhauled ) Screw –speed up to 130 r.p.m. additional Temperature controllers for down-stream equipment Control-Board with melt-pressure sensor / Display. Inspectiuon visist / trial-run shortly by appointment in our workshop Wuppertal Germany possible. We can offer, installed to this extruder: > screen-pack-changer > pelletizing ( strand, hot-face or waterring ) > other equipment Send us your inquiry. More extruder and complete pelletizing lines ex our workshop Wuppertal, send us your inquiry or visit us, you´re welcome

Year of construction: 1980, condition: reconditioned (used), machine/vehicle number: 2489, stock-No.:2489 1 used, functionally tested Single-Screw-Extruder, ready for trial-run: Manufacturer: KUHNE Germany Type: ES 60-24 Screw- Ø 60 mm – 24 LD Main-feed zone can be chilled( cooling unit not included ) Screw speed up to 100 r.p.m. Extruder Motor: 25,5 kW – 63 A – DC 4x Heating zones with air-cooling Gedpfx Aed Sg Hcjh Hobg 3x additional heating zones for down-stream equipment as: die-head, tools, screen-pack-changer, etc. control board Relating down-stream-equipment as screen-pack-changer, pelletizing etc. against additional price, details upon request. More extruders ex stock available, visit us or ask for our most recent Machine-Stock-List. You´re welcome.