Used Cross-Léger for sale (4,319)

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Nledou Tg I Djpfx Aqveb Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: like new (used), Range (in depending on the lighting conditions) until: 15 m Range with laser receiver: 30 m, & more 5 m: leveling accuracy +/-1 mm Nedpfx Aed Ecncoqvjlb Self leveling range: 4° +-0,5 ° Accuracy of the horizontal line at 5 m: +-1.5 mm Accuracy of vertical line at 3 m +-0.75 mm Number of laser lines: 2 Weight: 485 g

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg Njdpfx Aefv Hphsqvjlb

Condition: excellent (used), Catalogue number 7937 TECHNICAL DATA - max. blade diameter: 500mm - spindle diameter: 30mm - top pneumatic clamp - blade guard cover - pneumatic blade feed - max. cutting height: 150mm - max. cutting width: 350mm - main motor: 5.5kW - extraction port diameter: 120mm - table dimensions (LxW): 740x500mm - table height from base: 900mm - roller tables: 2 pcs - infeed roller table with guide: 2050mm - outfeed roller table: 1650mm - roller table width: 510mm - overall machine dimensions without table (LxW xH): 1200x640x1280mm - weight approx. 500kg ADVANTAGES Nsdpfxoy Tw Sks Aqvslb – Manufactured in Poland – Original technical documentation (DTR) – 2 roller tables – Pneumatic blade stroke – Used saw, excellent condition Net price: 14,900 PLN Net price: 3,550 EUR (based on 4.2 EUR exchange rate) (Prices may vary due to exchange rate fluctuations)

Condition: excellent (used), Catalogue No.: 7858 ADVANTAGES – Polish production – for cross-cutting packages or round timber – unpainted – mobile, on wheels – used saw, in very good condition TECHNICAL DATA guide bar length: 2100 mm cutting length: 1900 mm automatic lubrication of the cutting system damping and tension system in the head Nlsdpsy Tw Apefx Aqveb manual guide bar feed electric motor: 7.5 kW transport dimensions (L/W/H): 1900x900x2710 mm total weight: 205 kg Net price: 28,900 PLN Net price: 6,880 EUR (based on exchange rate 4.2 EUR) (Prices may change in the event of significant fluctuations)

Condition: used, Year of construction: 2003, Saw blade diameter: 350 mm, bore diameter: 30 mm, motor: 2 kW, speed: 3800 rpm. Extraction connection diameter: 95 mm. Weight: approx. 105 kg without stand. Cutting width at 90°: 430 mm, at 45°: 300 mm. Cutting height: 135 mm. Hydraulic return brake. Without stand and roller conveyors. Nodpfx Aqeyw Tzisvolb

Condition: used, cutting width 330 mm Cutting height 135 mm Motor output 2,2 kW The Graule type ZS 135 cross-cut saw is a pivoting cross-cut saw for cutting to length and mitre cuts. Njdpfx Aqsy Tpqljvjlb

Condition: used, Year of construction: 2007, Cutting height 175 mm cutting width 750 mm Motor output 5,5 kW saw-blade dia. 550 mm Njdpfx Ajy Tpqfsqvolb Weinig OptiCut C700 under-table cross-cut saw for safe and precise cross-cutting of solid wood, especially hard and heavy timber with large cross-sections. The machine works with a pneumatically guided saw unit, two-hand control and hold-down device and is ideal for sawmills, timber construction and industrial solid wood processing.

Condition: ready for operation (used), Year of construction: 1998, functionality: fully functional, machine/vehicle number: 10.7233, saw blade diameter: 450 mm, table length: 25,000 mm, The machine has had two owners, both well-known companies in Latvia. We have used the machine ourselves for 8 years. We are selling it because we have purchased new equipment. The machines are in full working order and stored in a heated facility. We can also demonstrate its operation on site. The equipment has been regularly maintained and repaired to ensure maximum profitability and the highest quality of the finger-jointed boards. Njdpfxey Ucpkj Aqvelb The machine can be inspected and tested in Kuldīga, Latvia. We are also selling the finger-jointing line that was purchased from Weinig together with this machine. Please see our separate advertisement.

Condition: ready for operation (used), Year of construction: 1998, functionality: fully functional, machine/vehicle number: 10.7233, saw blade diameter: 450 mm, cutting height (max.): 6,000 mm, positioning accuracy: 1 mm, cutting width (max.): 250 mm, total length: 25,000 mm, type of input current: three-phase, year of last overhaul: 2025, The machine has had two owners, both well-known companies in Latvia. We have used the machine ourselves for 8 years. We are selling it because we have purchased new equipment. The machines are in full working order and stored in a heated facility. We can also demonstrate its operation on site. Njdjy Ucn Tepfx Aqvjlb The equipment has been regularly maintained and repaired to ensure maximum profitability and the highest quality of the finger-jointed boards. The machine can be inspected and tested in Kuldīga, Latvia. We are also selling the finger-jointing line that was purchased from Weinig together with this machine. Please see our separate advertisement.

Condition: used, Year of construction: 2015, functionality: fully functional, Machines connected in one line (all three machines are only sold together): 1. Veneer cross-jointing machine FURNIMASTER FZR-21 2. Direct unloading device DA-12R 3. Scissor lift INCLUDED Veneer specifications Veneer strip length (grain direction) 350 - 2100 mm Veneer strip width (cross grain) 50 - 500 mm Veneer strip thickness 0,3 - 1,5 mm Power data Nlodpfx Aqey Tpb Rjveb Maximum nominal output / machine cycles 30 cycles/min. Average production speed 17 - 20 cycles/min. Connection data (Basic machine) Connection power 9 kW Compressed air 6 bar Power consumption Electric energy 6,2 kWh Compressed air 15 NL/min. Dimensions and weight (Basic machine) Length 3500 mm Width 1500 mm Height 1530 mm Working table height 930 mm (+50/-0 mm) Net weight, approx. 2500 kg

Condition: used, Year of construction: 2013, functionality: fully functional, Fisher+Rueckle FZR-24 Veneer cross-gluing machine, year 2013 for sale! Veneer strip length 400-1100 double lane/ 350-2100 mm single lane Veneer strip width 50-500 mm Veneer strip thickness 0.3-1.5 mm Max nominal output /machine cycles 30 cycles/min Average production speed 17-20 cycles/min Njdpfx Asumrf Aoqvjlb Effective length of heating zone 2478 mm Connection power 22 kW Compressed air 6 bar Glue types PVA or UREA based

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2026, volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Njdoy S Ru Aepfx Aqvjlb Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, number of aggregates 6 St. cutting width ~ 5.000 mm Cutting height ~ 100 mm Daveba multiple cross-cut saw for simultaneously cutting long boards to several shorter ones (with variable length) without mechanization. Njdpfjyztz Rjx Aqvslb The system is dismantled and ready for loading.

Condition: used, d1: 35 mm d2: 27 mm (wrench size) Total length: 115 mm - Available: 2 pcs Nedjlkclgopfx Aqvolb Price per piece: €25.00 + VAT.

Condition: good (used), Drilling machine, bench drill, pillar drill, column drill, box-type drill, tapping machine, threading machine -Manufacturer: Strands, MK3 bench drill with cross table Demanders -Motor: 0.75/1.0 kW -Speeds: 100 - 30200 rpm, 8-stage forward/reverse rotation -Thread cutting device: via foot switch -Table size: 500 x 195 mm -Cross table travel: X360 mm Y160 mm Z440 mm -Spindle mount: MK3 -Spindle stroke: 135 mm Nledpfxoy Rx Ego Aqvjb -Protrusion: 255 mm -Dimensions: 780/800/H1540 mm -Weight: 218 kg

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, saw blade diameter: 450 mm, cutting height (max.): 100 mm, cutting width (max.): 200 mm, type of input current: three-phase, year of last overhaul: 2025, For sale: Metal Technika OWD-1600 Optimizing Saw / Cross-cut Saw, year of manufacture 2018. The machine is fully operational, ready for immediate use – ideal for fast cutting of components in serial production. A major advantage of this machine is its ability to set a cutting schedule for up to 8 positions: you simply set the dimension and the quantity, and the machine automatically performs cutting and proceeds to the next positions without the need for tool changes. Technical Data: Model: Metal Technika OWD-1600 Year of manufacture: 2018 Maximum material width: 200 mm Maximum material height: 100 mm Maximum board length: 3200 mm Feed speed: approx. 30 m/min Saw blade diameter: min. 400 mm / max. 500 mm Motor speed: 2800 rpm Spindle speed: approx. 6000 rpm Power supply: 3x 400V Power: 7 kW Medium: air 6–7 bar Weight: approx. 1500 kg Performance: Njdpfx Aeyv Ewmsqvjlb The machine operates efficiently – for example: - Batch of 8 boards, 12 mm thick each - Board length: 2800 mm - Cutting into 3 elements (approx. 700 mm) - Cycle time: about 10 seconds The machine can be inspected and tested on site. Location: Elbląg / Warmińsko-Mazurskie, Poland For further questions, please contact me.

Condition: used, band length ca. 1.700 mm + 2.700 mm cutting width max. 2.500 mm Cutting height max. ca. 80 mm Nedpfx Aev Hgb Noqvelb

Condition: used, Year of construction: 2013, functionality: fully functional, One side scanner for sorting or optimization: Width: 30-200mm High: 13-50mm Length: 2-6m Possible to detect: Knots, wood structure, cracks, end cracks, color variations etc. Nlsdpfxov Tlgds Aqvob Scanning speed: up to 200m/min Possible to scan different profiles

Condition: used, Year of construction: 2001, total height: 1,600 mm, total length: 1,300 mm, total width: 1,350 mm, - Year: 2001 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 24.095.2 - Transport dimensions: 1300mm x 1350mm x 1600mm (l x w x h) Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Nlsdpjwnilrefx Aqvjb Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), functionality: fully functional, Grecon Dimter Opticut S50 Optimizer Maximum infeed material length: 5000 mm Minimum/maximum wood width: 20-300 mm Minimum/maximum wood thickness: 10-100 mm Possibility of bundle cutting Defect cutting in material Nljdpfx Aey E Shkoqvob CE Certificate DTR documentation Reference image of the machine

Year of construction: 1991, condition: used, The Filtrox Cross Flow microfilter works with a permissible transmembrane pressure of 6 bar (0 °C - 95 °C) and a filtrate volume of 4.5 - 7 hl/h with a filter surface area of 26.4 m². Two pumps (20 kW) in the unfiltrate circuit transport the medium to be filtered. With 16 hl agitator tank as cleaning tank. Additional title: yeast-beer recovery Capacity: 7 hl/h Tol. operating pressure: 10 bar Tol. operating temperature: 85 °C Max. filter area: 26 m^2 Current: 4,85/2,8 A Voltage: 220/380 V Frequency: 50 Hz Operation / Control: Simatic S5 Nlsdpfx Ajvcq Daoqvjb Features: 8 ceramic membrane modules (total filtration area 26.4 m2); high-pressure pump; 16 hl cleaning tank with agitator; various pipes, valves, measurement and control technology

Condition: excellent (used), Double miter saw Pertici Haffner DGS180 Cutting length: 3300 mm Cutting width: 140 mm Two adjustable cutting angles Nlodjxg Hanopfx Aqvsb Maximum saw blade diameter: 330 mm Pneumatic material clamps 3 operating modes

Condition: excellent (used), Rema AP-500 Optimizing Saw Infeed material length: 500–6250 mm Nodpext Ezkofx Aqvslb Blade diameter: 500 mm Motor power: 6 kW Pusher speed: 60 m/min Defect cutting: fluorescent chalk reader Margin trimming CE certificate DTR technical documentation Year of manufacture: 2018

Condition: good (used), GUK FA 49/4 Folding Machine + GUK FA 49/4 Cross Folding Module The machine is in very good technical and visual condition. Format: 490x690mm. Folding speed: 30-160m/min Equipment: 4 parallel cassettes on the main unit 4 perpendicular cassettes on the cross-folding unit First cassette extended. Cassette adjustments are dial-based. Nedpfxoy Ehk Is Aqvslb Smooth speed control. Counter with batching function and folding speed indicator. Rietschle compressor. Tool roller with a large number of perforating, creasing, and cutting tools. Raised sound insulation covers. Vacuum-assisted feeding Mobile delivery (free standing delivery) with smooth speed control Full documentation. Extensive set of accessories.