Used Turn Cross for sale (11,794)

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg Bjdpfx Abozp H R Estsdg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: good (used), Year of construction: 2006, Machine used only for plastic. Bodpeu Ibihefx Abtsdg Technical details shown in attached pdf document. Parts shown by hand not come.

Condition: good (used), Year of construction: 2016, FOR SALE CNC Lathe TOP TURN S20C – Year 2016 Brand: TOP TURN (Distributed by major machine tool networks) Model: S20C Year: 2016 CNC Control: FAGOR (User-friendly interface for teaching cycles and ISO programming) Technical Description This 2016 CNC lathe is a versatile machine, ideal for precision work in small to medium production batches. Its modern design offers excellent rigidity and very quick set-up, thanks to the Fagor control system. Capacity: - Swing over bed: 400 mm - Swing over carriage: 210 mm - Distance between centers: 1,000 mm - Bed width: 300 mm Spindle: Bdedpsy Slttefx Abteg - Spindle bore: 52 mm (Comfortable bar capacity) - Spindle speed: Up to 2,500 rpm - Spindle nose: Camlock D1-6 Included Equipment - FAGOR CNC: Color screen, cycle-assisted programming (ideal for operators used to conventional machines) - Turret: Automatic turret (electric/hydraulic) for fast and programmable tool changes - Chuck: Precision 3-jaw chuck (approx. 200 mm diameter) - Tailstock: CM4, robust - Safety: Fully enclosed machine with interlocked sliding doors, compliant with CE standards - Coolant system: Centralized with integrated chip tray Highlights - Recent (2016): Modern electronic and mechanical components, easy to source spare parts - Precision: High-precision ball screws on both axes - Compact: Small footprint relative to its machining capacity Weight and Dimensions - Dimensions: Approx. 2,400 x 1,400 x 1,700 mm - Weight: Approx. 1,800 kg

Condition: like new (used), Range (depending on lighting conditions): up to 15 m Range with laser receiver: 30 m and more Leveling accuracy at 5 m: +/- 1 mm Self-leveling range: 4° +- 0.5° Bdjdjd Ecncepfx Abtog Accuracy of the horizontal line at 5 m: +- 1.5 mm Accuracy of the vertical line at 3 m: +- 0.75 mm Number of laser lines: 2 Weight: 485 g

Year of construction: 1981, condition: good (used), Spindle motor for CNC lathe MAZAK SLAT TURN 30, year of manufacture 1981. Bsdpfx Abjxr Dhystodg

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery Bedpfx Abjfv Hphetodg PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, controller model: Siemens 840 D, table diameter: 1,220 mm, TECHNICAL DETAILS Table diameter: 1,220 mm Max. turning diameter: 1,500 mm Max. height under the cross beam: 900/1,200 mm Saddle travel, X-axis: 1,000 mm Table speed range: 4.5 to 100 RPM Bjdpfxszuy Eae Abtjdg Feed rate range: 0.127 to 6.35 mm/rev Tool changer: 30 positions MACHINE DETAILS Control system: Siemens 840 D Main drive motor: 41 kW EQUIPMENT 8 clamping jaws 30 tool holders Full enclosure Mist extraction system

Condition: like new (used), Year of construction: 2022, functionality: fully functional, machine/vehicle number: 100418005, travel distance X-axis: 1,500 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 590 mm, feed length X-axis: 30,000 mm, feed length Y-axis: 30,000 mm, feed length Z-axis: 30,000 mm, feed rate X-axis: 30 m/min, feed rate Y-axis: 30 m/min, feed rate Z-axis: 30 m/min, mount diameter: 63 mm, total length: 9,485 mm, table length: 1,000 mm, total width: 4,609 mm, spindle speed (max.): 10,000 rpm, total height: 2,896 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, type of input current: three-phase, table load: 300 kg, position of the milling head: Horizontal / Swiveling, workpiece weight (max.): 300 kg, torque: 136 Nm, rotational speed (min.): 3,800 rpm, rotational speed (max.): 16,000 rpm, overall weight: 18,000 kg, working range: 1,000 mm, spindle nose: HSK-A63, tool weight: 6 g, grinding spindle motor power: 54,000 W, spindle motor power: 54,000 W, Equipment: rotational speed infinitely variable, Zero hours HSTM 1000HD 5-Axis Turn-Milling Center Was not used in production / just OEM commissioning and preserved. Basic machine HSTM 1000HD X, Y, Z axis with absolute linear scale A axis Swivel axis / B axis C axis Pressure control of head clamping CNC-control system SIEMENS 840D SL Remote diagnosis system via Ethernet Patrol light Control cabinet with air-condition Milling spindle 16’000 rpm, HSK-A63 Machining hour counter Tool handling system with double gripper Chill unit Hydraulic unit Machine housing with front door L shape Standard machine color scheme Coolant supply unit, low pressure, paper belt filter Flush Gun Chip conveyor Oil Mist exhaust system Documentation 1-fold in English + CD Machine option package Minimum quantity lubrication system High pressure cooling through spindle BEMA automatic adjustable coolant nozzles Tool measuring system BLUM Work piece measuring system BLUM 3D Probe Rotoclear window Handweel HT 2 Automatic operator doors CAD / CAM Software package “ Hamuel Single Blade” CSE Siemens simulation Transportation and lifting tool set Bjdpozvuu Sefx Abtsdg Commissioning tool set Geometrical measurement set Available in Bangkok, Thailand Worldwide shipping

Condition: like new (used), Year of construction: 2022, functionality: fully functional, machine/vehicle number: 100372005, travel distance X-axis: 800 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 465 mm, feed length X-axis: 40,000 mm, feed length Y-axis: 40,000 mm, feed length Z-axis: 40,000 mm, feed rate X-axis: 40 m/min, feed rate Y-axis: 40 m/min, feed rate Z-axis: 40 m/min, mount diameter: 63 mm, total length: 5,350 mm, table length: 500 mm, table width: 450 mm, total width: 5,116 mm, spindle speed (max.): 16,000 rpm, total height: 3,082 mm, rapid traverse X-axis: 40 m/min, rapid traverse Y-axis: 40 m/min, rapid traverse Z-axis: 40 m/min, type of input current: three-phase, table load: 250 kg, position of the milling head: Horizontal / Swiveling, workpiece weight (max.): 250 kg, torque: 63 Nm, rotational speed (max.): 16,000 rpm, overall weight: 16,000 kg, working range: 500 mm, tool weight: 6 g, input voltage: 400 V, input frequency: 50 Hz, input current: 90 A, workpiece length (max.): 700 mm, workpiece width (max.): 400 mm, number of slots in tool magazine: 24, Equipment: documentation/manual, rotational speed infinitely variable, Zero hours HAMUEL HSTM 500 HD 5-Axis Turn-Milling Center Was not used in production / just commissioning (by OEM) and preserved. Comes as complete shipset from MFG. - X, Y, Z axis with absolute linear scale - A axis - Swivel axis / B axis - C axis - Pressure control of head clamping - CNC-control system SIEMENS 840D SL - Remote diagnosis system via Ethernet - Patrol light - Control cabinet with air-condition - Milling spindle 16’000 rpm, HSK-A63 - Machining hour counter - Tool handling system with double gripper - Chill unit - Hydraulic unit - Machine housing with front door L shape - Standard machine color scheme - Coolant supply unit, low pressure, paper belt filter - Flush Gun - Chip conveyor Bedpszvulksfx Abtodg - Oil Mist exhaust system - Documentation 1-fold in English + CD Machine option package: High pressure cooling through spindle BEMA automatically adjustable nozzles Tool measuring system BLUM Work piece measuring system BLUM Rotoclear window Handweel HT2 VNCK Siemens simulation Available in Bangkok, Thailand Worldwide shipping

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, CNC Horizontal Lathe Mori Seiki NL2000Y/500 Year 2012 Controller : MAPPS III Max Swing Ø923mm Max over cross slide Ø755mm Max Turn Ø356mm Bar Capacity Ø65mm Bdjdpfx Abjwvrfketog Travel X260mm / Z590mm Y +/-50mm Spindle Speed 5000rpm Turret 12 stations Max. milling speed 6,000rpm Chip conveyor Stock Clearance at 39.000EUR ONLY

Condition: new, Year of construction: 2026, functionality: fully functional, turning height: 2,300 mm, workpiece weight (max.): 12,000 kg, turning diameter over cross slide: 2,650 mm, turning diameter: 2,700 mm, faceplate diameter: 2,000 mm, total height: 7,100 mm, total width: 5,500 mm, total length: 8,500 mm, rotary table diameter: 2,000 mm, rotational speed (max.): 250 rpm, rotational speed (min.): 1 rpm, spindle speed (min.): 5 rpm, spindle speed (max.): 2,500 rpm, table load: 12,000 kg, table diameter: 2,000 mm, warranty duration: 24 months, overall weight: 63,000 kg, faceplate torque: 43,000 Nm, repeat accuracy: 0.015 mm, REM SCR 27 1SF — CNC Vertical Turning & Milling/Drilling Center 🔴 MACHINE CURRENTLY UNDER ASSEMBLY — DELIVERY MAX 3 MONTHS 🔴 24-MONTH WARRANTY — LONGEST IN ITS CLASS 🔴 UNBEATABLE PRICE FOR EUROPEAN CNC QUALITY ━━━━━ MACHINE HIGHLIGHTS ━━━━━ ✓ Complete turning + milling + drilling in ONE setup ✓ 12-Station ATC — bi-directional, 30 sec tool change ✓ Live spindle ISO 50 — 5 to 2,500 RPM | 37 kW ✓ C-Axis for full contour milling ✓ FANUC 0i-TF PLUS CNC — global support ✓ Heidenhain absolute measuring system (X: LC 195F) ✓ CE certified, full enclosure 3,300mm height ✓ Heavy-duty Meehanite cast iron structure ━━━━━ TECHNICAL SPECIFICATIONS ━━━━━ • Max Machining Diameter: 2,650 mm | Swing: 2,700 mm • Max Machining Height: 2,300 mm • Table Diameter: 2,000 mm (8 T-slots + 4 clamping jaws) • Max Workpiece Weight: 12,000 kg • Table Speed (turning): 1–250 RPM • Main Motor: 100 kW FANUC servo | Torque: 43,000 Nm • Ram Cross Section: 250×250 mm • X/Z Rapid Feed: 10,000 mm/min | Feed: 0.02–6,000 mm/min • X/Z Thrust Force: 35,000 N • ATC: 12-station disc | Max tool Ø 300mm | L 400mm • Coolant: 2,000 L tank | External 10 bar | Through-spindle 40 bar • Chip Conveyor: SARIGÖL hinged, 500mm wide • Accuracy: ±0.020 mm/m | Repeatability: ±0.015 mm • Electrical: 400V/50Hz | 140 KVA | Fanuc 0i-TF PLUS Bjdpfxozb Ufvj Abtedg • Weight: 63,000 kg | 8,500×5,500×7,100 mm ━━━━━ IDEAL APPLICATIONS ━━━━━ Large gear blanks | Ring gears | Wind energy hubs & rings Heavy castings & forgings | Oil & gas flanges Mining equipment components | Aerospace large parts ━━━━━ COMMERCIAL TERMS ━━━━━ Delivery: MAX 3 MONTHS from order Warranty: 24 MONTHS parts + labor Incoterms: EXW Bacău, Romania Payment: 50% advance + 50% before shipment Installation & commissioning: included Manufacturer: REM Bacău, Romania

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, - FANUC i Series TD - Max. turning diameter: 420 mm - Max. swing dia over bed 670–850 mm - Max. turning length 3190 mm - Spindle speed: 2800 RPM - Spindle motor power: 22–25 kW - Spindle bore / Chuck size: 102–132 mm / 12 inches - X-axis travel: 293 mm - Y-axis travel: ±65 mm - Z axis travel: 3190 mm - Live tool speed: 5000 rpm - Number of tool stations on the turret: 12 - Machine weight: approx. 13000 kg Bdedpfx Aszw N H Esbtsg Accessories, features - Coolant unit - Chip conveyor - Tailstock - Hydraulic steady rest - C axis - Y axis - Live tool turret - Towel lamp - Transformer - Integrated hydraulics - 3 jaws hydraulic chuck - Tool eye (tool presetter) - Tool holders (live holders too) - Documentation The machine was owned by a sheet metal production company and the machine was barelly used. Very good condition. Under power in our showroom.

Condition: good (used), For sale is the lathe shown in the pictures, manufactured by the Japanese brand Mazak, model Quick Turn 8n, with Mazatrol T32-2 control. The machine is equipped with a bar feeder and a collet chuck. We can arrange for machine loading at the location. Net price: 23,000 (plus 23% VAT) Turning diameter: 160 mm Maximum turning length: 285 mm Spindle bore: 40 mm Maximum spindle speed: 6000 rpm 8-position turret Bdodezc Ri Tspfx Abtsg Tailstock included Tool measuring probe Weight: 2700 kg

Condition: used, Year of construction: 1999, functionality: fully functional, cutting height (max.): 100 mm, cutting width (max.): 2,500 mm, saw blade diameter: 400 mm, height adjustment type: mechanical, Equipment: saw blade guard, Double-blade panel saw, Eima Type 122 Cutting width, min/max: 210-2500 mm Bdsdpfxezwkrvj Abtog Cutting depth: 2500 mm Maximum blade diameter: 400 mm Cutting height: ~100 mm Motor power: 2 x 4.4 kW Electronic cutting width adjustment

Condition: used, Year of construction: 2005, functionality: fully functional, turning length: 1,500 mm, spindle speed (max.): 4,000 rpm, rotational speed (max.): 4,000 rpm, overall weight: 14,400 kg, Mazak Integrex 300 3 ST Control -Mazatrol 640 mt pro 2 Spindles 1500mm No CE Bjdpsx Rkvqofx Abtjdg 2005/05 in very good condition Turret lathe.....10 tool ATC.....40 tool Maximum Swing 33.5″ 850.9 mm Maximum Swing (Y-axis use) 26″ – 33.5″ 660.4 mm – 850.9 mm Maximum Swing over Cross Slide 33.5″ 850.9 mm Maximum Swing over Lower Turret 16.5″ 419.1 mm Located in Israel under power and ready for inspect . This CNC made in Japan and definitely needs a permit of MATI

Condition: good (used), Year of construction: 2008, Ref. -No.: 10657 Bedpfezx Nzfex Abtedg Manufacturer: EMAG Type: EMAG VTC 250 Year of construction: 2008 Type of control: CNC Control: Siemens Sinumerik 840D Storage location: Hakberstadt Country of origin: Germany Turning Length: 630 mm Tool Taper: VDI 40 Turret places: 1 Pcs Number of tool stations: 12 pc Turning Speeds: 5000 RPM Chuck diameter: 250 mm Further information: - The machine features an overhead drive spindle with a tailstock at the bottom. - Coolant tank, approx. 1,000 L, including - a paper filter roll. - Clamping devices: Hainbuch clamping top, including various centering tips - Gripping devices on the turrets for feeding and removing raw and finished parts during magazine operation. - Magazine loading - Vertical pick-up lathe, which can generally be easily upgraded for automatic loading and unloading. The machine can be viewed while powered on by prior arrangement.

Condition: good (used), Year of construction: 2001, Ref. -No.: 10551 Manufacturer: TRAUB Type: TNC 42/65 Year of construction: 2001 Type of control: CNC-Steuerung Control: TRAUB TX Storage location: Halberstadt Country of origin: Germany Machine-No.: 93XXXXX Turning Speeds: 8000 RPM X stroke: 450 mm Turning Length: 450 mm Spindle Speeds: 4000 RPM Clamping Diameter: 42 / 65 mm Spindle Diameter In Front Bearing: 110 mm Tool Taper: 14 Max. Torque: 170 / 230 Nm Rapid Travel Speed X-Axis: 15 m / min Rapid Travel Speed Y-Axis: 6 m / min Rapid Travel Speed Z-Axis: 30 m / min Dimensions Of The Machine (Lxwxh): 4354 x 2076 x 1917 m Chisel slide cross section turning and milling support: 16 x16 ( 20 x20 ) mm Pressure: 70 bar hydraulic tank: 70 L. Bodpjzx Nx Rjfx Abtedg Total Power Requirement: 39 kVA Weight Of The Machine Ca.: 5,2 t Feed force X-axis at 100% duty cycle: 5000 N Feed path X-axis: 140 mm Z-axis feed path: 450 mm Y-axis feed path: 35 mm Ball screw Z-axis (Ø x pitch): 32 x 10 mm Ball screw X-axis (Ø x pitch): 32 x 5 mm Ball screw Y-axis (Ø x pitch): 25 x 5 mm Further information: - Revolver 1 Number of branches 10 - Revolver 2 Number of branches 14 - Hecowpkfie Htlx Tfefh - Powered tools Yes The machine can be viewed under power by arrangement.

Condition: good (used), Year of construction: 2010, Ref. -No.: 10436 Manufacturer: SCHERER FEINBAU Type: VDZ 120 rechts Year of construction: 2010 Type of control: CNC-Steuerung Control: SIEMENS SINUMERIK 840 Storage location: Halberstadt Country of origin: Germany Machine-No.: 660XX Turning Speeds: 5500 RPM Swing Diameter: 260 mm Rapid Travel Speed X-Axis: 60 m / min Rapid Travel Speed Z-Axis: 30 m / min Travel -X Axis: 626 mm Travel -Z Axis: 250 mm Spindle bearing diameter: 32 mm Rated speed: 1200 1 / min Turret places: 12 Pcs Machine length: 1685 mm Machine width: 2400 mm Machine Height: 2850 mm Weight Of The Machine Ca.: 8 t Further information: Spindle head with short taper DIN 55026: A6 Pallet conveyor WPS KNOLL system (2010) Bodpjzx Nxkefx Abtodg SAUTER turret (12 places) Documentation available Tools in the pictures are sold with the machine. Machine can be inspected and demonstrated under power.

Condition: good (used), Year of construction: 2009, Ref. -No.: 10026 Manufacturer: SCHIESS Type: VMG4 MA90 Year of construction: 2009 Type of control: CNC-Steuerung Control: Siemens Sinumerik 840 D Storage location: Halberstadt Country of origin: Deutschland Turning Diameter: 5000 mm Turning Diameter Over Bed: 4000 mm Spindle Speeds: 0 - 120 RPM Clamping Diameter: 4000 mm Cross Travel: 420 x 340 mm Max workpiece height: 3000 mm Main Drive: 52 kW Max. Tension: 120000 N Max. Payload: 50 t Power Capacity - Table: 110 kW Max torque faceplate: 100 kNm Further information: Automatic tool changer with 80 positions (AAC) Automatic attachment changer for 6 milling heads Live spindle C-axis table Travel of the Y-axis gantry columns Drilling and milling head (master head principle) Straight drilling and milling head GB-1B Renishaw RBP 60 touch probe Hand terminal Teleservice Internal and external coolant Operator cabin Chip conveyor SADDLE (X-AXIS): Horizontal movement from the center to the right side 4,800 mm Horizontal movement from the center to the left side 3,100 mm Vertical distance between the saddle rails 1,400 mm Speed / range 0 - 16,000 mm / min GANTRY TRAVEL (Y-AXIS): Gantry stroke 5,000 mm Feed 0 - 16,000 mm / min RAM (Z-AXIS): Maximum cutting force when turning 60 Kn Enter minimum bore 550 mm Guide length 1,600 mm Speed / feed range 0 - 16,000 mm/min Spindle speeds: Bjdpfxozx Nw Ts Abtedg Range 1 rpm Range 2 0 - 1,100 - 3,150 rpm Spindle torque: Range 1 2,400 - 2,400 - 850 Nm Range 2 450 - 450 - 160 kNm

Condition: used, Year of construction: 2008, operating hours: 51,226 h, functionality: fully functional, Control system: HEIDENHAIN Plus iT with Turn Plus Bjdpfozx Agzjx Abtjdg Turning length: 1175 mm (tailstock machine 1100 mm) Tool holder: HSK 63A (DIN 69893) Tool magazine: 1 x 36-position disc magazine Note: We offer flexible financing solutions for all machines as well as a professional relocation service. Dismantling, transport, and expert reassembly – all from a single source. Billing based on individual terms and conditions and duration. Contact us for your personal offer.

Condition: used, Grecon Dimter Opticut 704 Optimizing Saw Bdedpjzvyk Sefx Abteg An optimizing saw for demanding applications. A continuous chain transport system with a flexible upper clamping device, from the measuring station to the saw, ensures safe transport of wood that is tapering, twisted, heavily rough after sanding, and prone to splitting. A servomotor with a planetary gearbox provides very high acceleration due to its low moment of inertia. Waste is blown to the side in the cutting area. Thanks to its special design with an aluminum casting and a pneumatically controlled saw swing, very short cutting times are possible. The output is approximately 12,000–17,000 running meters per shift, with maximum cross-sections of the material being processed ranging from 100 × 100 mm to 30 × 250 mm.

Condition: good (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: 00820002981, turning length: 800 mm, turning diameter: 500 mm, spindle speed (max.): 3,600 rpm, spindle bore: 118 mm, rapid traverse X-axis: 36 m/min, rapid traverse Y-axis: 40 m/min, rapid traverse Z-axis: 30 m/min, bar passage: 102 mm, total height: 2,500 mm, total length: 8,000 mm, total width: 2,400 mm, overall weight: 10,000 kg, controller manufacturer: DMG, controller model: ERGOLINE, input voltage: 400 V, input frequency: 50 Hz, input current: 125 A, nominal power (apparent): 74 kVA, operating hours of spindle: 4,439 h, Equipment: chip conveyor, DMG MORI CTX BETA 800 TC CNC turning and milling center - Note: the spindle hours may increase slightly! - Swing diameter: 500 mm - Distance between centers: 1020 mm - Max. workpiece weight (chuck parts/chuck weight): 100 kg - Max. workpiece center of gravity from spindle flange: 120 mm - Travel X1: from -10 to 490 mm - Travel Y1: +-100 mm - Travel Z1: 845 mm - Travel Z2: 600 mm - Travel Z3: 800 mm - Spindle flange diameter: 220 H 5 mm - Chuck diameter: 315 mm - Diameter of front bearing: 160 mm - Rapid traverse speed, Z-axis: 40 m/min Bodpfx Aezxx Dcjbtodg - Resolution, Z-axis: 0.001 mmm - B-axis max. swivel speed: 70 rpm - Angular resolution: 0.001° - Tailstock travel: 800 mm - Quill force: 8 kN The machine is equipped with a tailstock and a three-jaw chuck, diameter: 250 mm, as well as a chip conveyor and coolant system. FCA D-63843 Niedernberg - loaded onto a truck.

Condition: good (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 00500000321, turning length: 2,000 mm, turning diameter: 630 mm, spindle speed (max.): 4,000 rpm, spindle bore: 118 mm, travel distance X-axis: 650 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 2,050 mm, total height: 3,500 mm, total length: 10,000 mm, total width: 5,000 mm, overall weight: 20,000 kg, controller manufacturer: DMG, controller model: ERGOLINE, input voltage: 400 V, input frequency: 50 Hz, input current: 160 A, nominal power (apparent): 110 kVA, operating hours of spindle: 14,700 h, Equipment: chip conveyor, DMG CTX GAMMA 2000 TC CNC Turning and Milling Center - Please note: the spindle operating hours may increase slightly! - Swing diameter: 630 mm - Distance between centers: 2260 mm Bdedszxxhhepfx Abtjg - Max. workpiece weight (chuck jaws/chuck weight): 250/150 kg - Max. workpiece center of gravity from the spindle flange: 250 mm - Travel range B1: 240° - Travel range Z2: 1910 mm - Travel range Z3: 1910 mm - Steady rest clamping range DW: 45 - 310 mm, weight: 152 kg - Steady rest width C: 145 mm - Spindle flange diameter: 220 H 5 mm - Chuck diameter: 500 mm - Bar diameter: 102 mm - Diameter of the front bearing: 160 mm - Tool holder: HSK 63 A - Includes a 36-position tool changer The machine is equipped with a tailstock, an automatic steady rest from SMW AUTOBLOK, and a three-jaw chuck from SMW, diameter: 300 mm. It also includes additional jaws, another chuck, a chip conveyor, and a coolant system. Please note: the machine can be transported on a truck with a width of up to 3000 mm. FCA D-63843 Niedernberg - loaded onto a truck.

Condition: used, Year of construction: 2002, weight max. 15 / 30 t workpiece diameter 600 - 6000 mm gear diameter 500 mm Bdedpozx Hcmsfx Abtsg total power requirement 2,2 kW weight of the machine ca. 1400 / 700 kg dimensions of the machine ca. 2,5x0,9x1,00/1,50x0,7x0,9 m

Year of construction: 2001, condition: good (used), functionality: fully functional, Machine is being sold due to factory closure. Includes a bar loader. Bdjdpezx Hv Hsfx Abtjg