Used Deep Load Trailer M Folding Auffahrr for sale (85,633)

Condition: new, maximum load weight: 36,360 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Telescopic loading platform with rear slope approx. 1,000 mm x 8° * 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing laths approx. 15 x 15 mm, including extensions at the bottom * Between the 1st and 2nd axle, one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) * Incl. 3-piece removable galvanized covers over the wheel recesses (width approx. 670 mm) – max. point load 5 t each * Recess in the slope and extending into the platform for accommodating an excavator dipper stick (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of horizontal lashing rings at the front of the platform (LC 10,000 daN) * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 2 pairs of fold-out lashing rings (LC 10,000 daN) * 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) * Cut-outs in the platform's outer frame for attaching tie-down straps (LC 2,000 daN) Two-Piece Steel Ramps: * One pair of galvanized, two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering * Ramps with hydraulically folding ramp sections and hydraulic lifting system, hydraulically adjustable * Maximum load per pair: 40,000 kg Landing Gear: JOST landing gear (mechanical) with 2-speed gearbox, lift capacity approx. 24 t (test load approx. 50 t) Axles: * BPW axles and suspension, 2 rigid axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated automatically by reverse gear and manually * Air suspension with lift and lower valve Tyres: * 235/75 R 17.5 3PMSF tyres – manufacturer of our choice TPMS: * TPMS tyre pressure monitoring system in accordance with ECE R 141 Brake System: * WABCO brake system according to EU regulations with EBS-E (2S2M) Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimum corrosion protection Bedpfx Aoyhkq Ueprolh * Final paintwork with two coats of 2K topcoat, solid RAL 3002 Carmine Red, in accordance with RAL System 841GL * Wheel rims in silver grey Incl. the following additional equipment: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * 3 pairs of recessed lashing rings along the central beam (LC 5,000 daN) * Electro-hydraulic power unit at the rear, under the loading platform * On the gooseneck: plug-in aluminum drop sides and tail board, approx. 2,440 x 400 mm (L x H). The rear galvanized stakes are removable (body length approx. 2,560 mm). * One galvanized toolbox integrated in the gooseneck chamfer * 2 pairs of WADER container pockets on the loading platform for a 20' or 30' container * 3 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the platform * 3 additional pairs of removable galvanized covers over the wheel recess – max. point load 3.5 t each * One removable galvanized intermediate table with 1 pair of WADER container pockets * 1 additional, hook-on intermediate table, approx. 300 mm wide * Intermediate table with offset load ar

Condition: new, maximum load weight: 37,075 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including immediately available and short-term delivery vehicles, on our website. Sample of the equipment. Full equipment details available on request. Neck (Gooseneck): * Gooseneck with front corners bevelled approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Loading area behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel approx. 1,000 mm x 8° * 6 pairs of external foldable lashing rings (LC 5,000 daN) * 2 pairs of external foldable lashing rings (LC 10,000 daN) * 1 pair of internal foldable lashing rings at the central beam front (LC 10,000 daN) * Cut-outs in the outer frame of the platform for hooking in tensioning straps (LC 2,000 daN) * Grating flooring C40/4 (point load approx. 2.3 t over an area of approx. 20 x 20 cm), treadplate flooring over the axles Two-piece Steel Ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with grating surface C40/4 (point load approx. 2.2 t over an area of approx. 20 x 20 cm) * Ramp with hydraulically folding ramp sections * Hydraulic lift unit, hydraulically adjustable * Maximum load per pair: approx. 40,000 kg Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 fixed axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock automatic via reverse gear and manual activation * Air suspension with lift and lower valve Braking System: * WABCO braking system in compliance with EU regulations with EBS-E (2S2M) Tyres: Tyres 235/75 R 17.5 3PMSF – make at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Paintwork: * HRM metallisation of the complete vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminium) to ensure maximum corrosion protection * Final coating with 2 layers of 2K topcoat, single-coloured in RAL 3002 Carmine Red as per RAL System 841GL * Rims in silver grey Accessories included: * 2-inch king pin * Galvanized steel front wall approx. 400 mm high * Grating in the gooseneck bevel C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * Grating in the platform bevel C40/4 (point load approx. 3.4 t over an area of approx. 20 x 20 cm) * Electric-hydraulic unit at the rear under the platform * Plug-in aluminium side and rear boards on the gooseneck, approx. 2,440 x 400 mm (L x H). Rear galvanized insert stanchions removable. (Body length approx. 2,560 mm) * Electric winch with radio remote control, approx. 5,400 kg lifting capacity, including approx. 9.5 mm thick steel cable, approx. 24 m long, with cable guide roller * Bolted approx. 5 t ring for winch cable loop on the neck without deflection pulley * One galvanized toolbox integrated in the sloped gooseneck with opening for a winch * Grating on the gooseneck C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * 7 pairs of stanchion sockets for plug-in stanchions, approx. 100 x 50 mm, in the outer frame of the platform * Lift axle on the front axle, controlled by TEBS E depending on actual axle load and current loading status Bedpfx Apoyhkrrorslh * 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 2 pairs in the lift bed, 5 pairs in the rear section of the platform

Condition: new, maximum load weight: 37,075 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available on request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear taper approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood floor approx. 30 mm thick Loading area: * Loading area after the gooseneck hydraulically liftable/lowerable, length approx. 2,800 mm, with rear taper approx. 1,000 mm x 8° * 6 pairs of folding outward lashing rings (LC 5,000 daN) * 2 pairs of folding outward lashing rings (LC 10,000 daN) * 1 pair of inward folding lashing rings at the front central beam (LC 10,000 daN) * Cutouts in the external frame of the loading area for attaching tension belts (LC 2,000 daN) * Grating surface C40/4 (point load approx. 2.3 t on an area of approx. 20 x 20 cm), over the axles checker plate Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with C40/4 grating (point load approx. 2.2 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically folding in/out ramp sections. Hydraulic lift system, hydraulically adjustable * Maximum load per pair: approx. 40,000 kg Landing gear: * JOST landing gear (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock via reverse gear and manual activation * Air suspension with lift and lower valve Brake system: * WABCO brake system according to EU regulations with EBS-E (2S2M) Tyres: Bodpfx Aoyhkqzeprelh 235/75 R 17.5 3PMSF – Manufacturer of our choice TPMS: * TPMS tire pressure monitoring system in accordance with ECE R 141 Paintwork: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimal corrosion protection * Final paint in 2 coats of 2K topcoat, solid color in RAL 3002 Carmine Red in accordance with RAL system 841GL * Rims in silver grey Including accessories: * 2-inch kingpin * One galvanized steel front wall, approx. 400 mm high * Grating in the gooseneck taper C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * Grating in rear taper of the loading area C40/4 (point load approx. 3.4 t on an area of approx. 20 x 20 cm) * Non-slip sand paint on the checker plates above kingpin and loading area * Electro-hydraulic unit at the rear under the loading area * On the gooseneck: plug-in aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). The rear galvanized drop-in stakes are removable. (Body length approx. 2,560 mm) * An electric cable winch with radio remote control, approx. 5,400 kg pulling force, including approx. 9.5 mm thick steel cable, approx. 24 m long, with cable guide pulley * Bolted 5 t ring for cable winch deflection on the neck without deflection pulley * One galvanized toolbox integrated in the beveled gooseneck with opening for a winch * Grating on the gooseneck C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area * Lift axle on the front axle with control via TEBS E depending on current axle load and loading condition * 7 pairs comple...

Condition: used, maximum load weight: 16,300 kg, overall weight: 22,000 kg, axle configuration: 1 axle, first registration: 08/2022, next inspection (TÜV): 09/2026, BPW 10t axles, frame construction made of high-strength Domex 700, total loading area 11,800mm, length of loading area 8,350mm, Knorr brake EBS 4s/2k (ASR), folding rear support legs 25,000kg, pneumatic valve for adjusting the N.4 wheel blockers, Electric winch with remote control, 3x2 lashing rings in the platform outer frame (8to), Aluminium frame L: 2,300mm - W: 500mm, hot-dip galvanized, Tool box, Loading platform rollers, Extendable bumper, Ramp bracket Bsdpfx Apsih E Hyjrelh

Condition: used, mileage: 2,44,000 km, power: 140 kW (190.35 HP), first registration: 08/2017, fuel type: diesel, overall weight: 4,800 kg, color: white, gearing type: automatic, emission class: euro6, number of seats: 5, Year of construction: 2017, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), parking heater, soot filter, RTW 519 WAS case new original Mercedes AT engine/gearbox overhauled the entire vehicle has been completely overhauled 8 units in stock (as of stickers on request incl. Stryker Power Load stretcher mount pneumatic siren (compressed air) air suspension at the rear guarantee up to 36 months possible very very good condition, ready for immediate use / vehicle is reconditioned, no dents or scratches / stretcher available for an additional charge / ABS + ASR, ESP / 2x airbag / electric outside mirrors / electric windows / 2x battery 12 V 88 AH / engine preheating / auxiliary heating / power steering / reinforced stabilizer / tachograph / air conditioning / immobilizer / work light at the rear, external connection 220V / fire extinguisher / center armrest / reversing camera / reading lamp / radio pre-installation / optical signaling system / bar & front flasher acoustic signaling system. Financing or hire purchase possible!!! Our used vehicles Special vehicles are checked, prepared and maintained by an experienced team of service technicians from the special vehicle industry, so that a TÜV or Dekra seal is as natural as the immediate operational readiness of all ambulances. Ultrasonic disinfection of the air conditioning in the driver and patient compartments was carried out. Vehicle is almost as good as new!!! We offer a 12-month guarantee on this ambulance!!! Can be extended to 36 months Sold without medical and technical equipment, but can be purchased separately. Blodpolb Nw Tefx Aprjh Our service - for you! * 20-40 immediately available ambulances always available immediately in our house * DEKRA or TÜV SEAL on request * FINANCIAL SERVICE - Financing - leasing or hire purchase can be individually tailored to your needs * GUARANTEE - up to 36 months possible for an additional charge * Accident replacement vehicles in stock * PREPARATION - All vehicles are professionally prepared and prepared for you by our team * You can find further vehicle offers and service points at: We look forward to your call / The G&G team is available to you at any time. We speak Italian - English - Polish - Spanish and can definitely help you if you are looking for a good used ambulance. This advertisement is only a preview of our vehicle and is not part of a purchase contract. Information provided on the Internet is non-binding descriptions and does not represent guaranteed properties. The seller is not liable for errors, input errors and data transmission errors. Subject to changes and prior sale!

Condition: new, maximum load weight: 33,750 kg, overall weight: 47,000 kg, axle configuration: 2 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete range of vehicles, including those available for immediate or short-term delivery, on our website. Excerpt from the equipment list. Full specification available upon request. Neck: - Gooseneck in SNT design to optimize load platform length, approx. length 3,750 mm - Gooseneck hydraulically raisable/lowerable and detachable - Technical kingpin load: 23,000 kg For tractor units: 4 x 2, 6 x 2, and 6 x 4 Low bed: - Low bed with external beams, extendable SUPER LOW design, approx. length 6,850 mm - Low bed with fixed hardwood floor (approx. 40 mm thick) and mechanical locking - Supply lines run protected inside the extendable beams and adjust automatically to the respective bed length - 5 pairs of fold-out lashing rings (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for fitting bolted RUD rings Rear running gear: - Rear running gear with closed outer frame, checker plate surface, and continuous prism-shaped digger recess, approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of laying lashing rings in the recess LC 16,000 daN - 1 pair of laying lashing rings in the recess LC 10,600 daN - 2 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame PENDLE-AXLE: - PENDLE-AXLE system, all axles forced-steered hydro-mechanically - Hose break valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins to secure in raised position - Axles finished with 2 layers of 2K paint, single-color painted in FAY-Grey-34-0260 - Technical axle load: 12,000 kg per axle, hydraulic axle compensation - Axle tools - Tyres: 245/70 R 17.5 3PMSF – Brand at our discretion. Load index (146/146F) TPMS: - TPMS tyre pressure monitoring system according to ECE R 141 Brake system: - Wabco braking system compliant with EU regulations, with EBS-E (2S2M), without connecting lines to the tractor unit Electrical system: - Electrical system per EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the turn signal - ASPÖCK-UNIBOX at the front connection panel with sockets 24N, 24S & 15-pin. Connection according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel structure: - Steel structure made of high-strength fine-grained steels Bledpfxoxbmn Ue Aprsh - Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Painting: - Complete steel structure automatically shot-blasted after welding with a blast wheel system - Second blasting with corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K topcoat, single-color in RAL 3002 carmine red per RAL system 841GL Including the following additional equipment: - 2-inch kingpin - One galvanized steel front wall, approx. 400 mm high - Remote steering from front and rear via cable control with push buttons, including axle tracking control (without installation in tractor unit) - Electro-hydraulic power unit - 2 pairs of bolted container locks on the outer beams; includes 2 pairs of container locks for 1 x 20' or 1 x 40' container - On the gooseneck: removable aluminum side and rear walls, approx. 2,440 x 400 mm (L x H) - Rear galvanized plug-in stakes are removable

Condition: excellent (used), Year of construction: 1999, LNG Methan Gas Cryogenic Semi-trailer M1 Engineering Hersteller: M1 Engineering Baujahr: 1999 Volume: 49 m3 Working pressure: 8 bar. Tare 15435 kg Pump Bsdpfxjwp Iq Ae Aprelh Flowmetter We also have other tankers, tanks, vessels for LIN, LOX, LAR, LNG and CO2, argon, oxygen, nitrogen and carbon dioxide, LNG, Hydrogen, Methane We will be glad to answer your questions via Phone and E-mail

Condition: used, maximum load weight: 39,780 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, first registration: 01/2023, next inspection (TÜV): 01/2027, total width: 2,540 mm, Equipment: ABS, You can find our complete range of immediately and short-term available vehicles on our website. Bjdpfx Apex Uvlrjrolh Excerpt from equipment – full equipment list on request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear slope approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Extendable loading platform * 5 pairs of folding external lashing rings (LC 5,000 daN) * 3 pairs of folding external lashing rings (LC 10,000 daN) * 1 pair of recessed front lashing rings in the platform (LC 10,000 daN) * Cutouts in the outer frame for lashing strap hooks (LC 2,000 daN) * Hardwood floor approx. 48 mm thick, over axles with checker plate covering Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: * 205/65 R 17.5 twin tyres Axles: * BPW axles, two fixed axles, two air-suspended trailing steering axles with drum brakes and lift/lower function * Trailing steering axles can be locked electronically during reversing via reverse gear or manually Brake System: * Brake system in accordance with EU regulations with EBS-E (4S3M), without connecting lines to the tractor unit Steel Construction: * High-strength fine-grain steel construction * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Painting: * First-class, durable anti-corrosion protection on the standard shot-blasted welding frame, ensured by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) top coat, single color, RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 pure white * Wheels in silver Electrical System: * Electrical system according to EU regulations Lighting: * 24 Volt ASPÖCK-NORDIK (ASS3), ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Accessories included: * 2-inch kingpin * Galvanized steel front wall approx. 400 mm high * Spare wheel carrier in front of front wall * Yellow-red air couplings at the galvanized front connection panel * 4 wheel chocks with holders on the front wall * Mounts in the rear area of the gooseneck for ALU ramps * Galvanized folding supports under the rear slope of the loading platform * Bracket for warning beacon at rear of trailer * Yellow reflector tape as per EU regulations on sides, sliding section, and rear of trailer * On gooseneck and rear end, left and right, holders for warning boards incl. socket * Mud flap at rear of trailer * Manual and documentation on USB stick * European reflector signs (red-yellow) at rear * 80 km/h speed stickers at rear and both sides * Acoustic reverse signal * Load manometer for axle load determination incl. load diagram

Condition: new, maximum load weight: 91,640 kg, overall weight: 1,26,000 kg, axle configuration: > 3 axles, total width: 2,850 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment features. Full specification available upon request. Gooseneck * Hydraulically liftable/lowerable and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie * Hook couplings front and rear, length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Excavator Deck * Telescopic excavator deck BB-A with drive-over deck hooks at the front and a bolt coupling at the rear * Base width: approx. 2,850 mm, Length: approx. 7,150 mm, Main beam height: approx. 430 mm, Main beam width: approx. 1,350 mm * Loading height approx. 580 mm with ground clearance approx. 150 mm 5-Axle Rear Bogie * Mechanical bolt coupling for front connection of a low-bed, rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * 3-axle pendulum axle Front Bogie * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and stopper pins for securing in raised position * Axles finished with 2 layers of MB7350 Novagrau single-colour 2-component paint * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation * Front bogie tyres: 12 x Manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J, pendulum axle 5-Axle Rear Bogie * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and stopper pins for securing in raised position * Axles finished with 2 layers of MB7350 Novagrau single-colour 2-component paint * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation * Rear bogie tyres: 20 x Manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork * HRM metallization of the entire vehicle chassis using ZINACOR 850 (85% zinc/15% aluminium) to ensure the best possible corrosion protection * Final coat with two layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, according to the RAL System 841GL. Rims in silver grey Incl. Accessories * Steel front wall, approx. 400 mm high * Detachable ALU side walls and rear wall approx. 400 mm high in anodized finish, mountable on the gooseneck * 3.5" kingpin * BEKA-MAX central lubrication system for one gooseneck * Multi-coupling hydraulic connections on the gooseneck * BEKA-MAX central lubrication system for one 3-axle bogie * One 7-pin socket left and right rear on the front bogie for warning signs * Screw-in option (ø approx. 40 mm) every approx. 500 mm on the outside of the upper flange of the external tube of the excavator deck for lashing rings (LC 16,000 daN) * Folding extensions with steel mattress, width adjustable from approx. 2,850 mm to approx. 3,250 mm * Steel mattresses can be positioned in 2 ways to achieve a lowered loading platform. Load capacity depends on extension, refer to the respective load chart * Steel mattresses with rubber flooring approx. 12 mm thick * One 7-pin socket left and right, front and rear of the rear bogie for warning signs Bjdpfx Aouvbdtsprelh * BEKA-MAX central lubrication system for one 5-axle bogie * Socket on the rear bogie for cable remote control of rear steering * Rear bogie with trough * Two INOX toolboxes, approx. 855 x 340 x 390 mm, mounted on the goos

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump Blodpfx Asxf Silspreh - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)

Condition: used, maximum load weight: 37,535 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 08/2024, next inspection (TÜV): 08/2026, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and soon-available vehicles, on our website. The following is an excerpt from the equipment specification. Full equipment details available on request. Loading Platform: * Extendable loading platform with pneumatically operated locking mechanism * 7 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Bledpfxsxgk U No Aprjh Axles: * BPW axles, air-suspended, with disc brakes (approx. 430 mm), fitted with lift/lower function. Technical axle load: 10,000 kg each (ET0) * Self-steering axle with electromagnetic reverse lock, activated via reverse gear or manually * Axle tool Tyres: * Tyres 385/65 R 22.5 Brake System: * Brake system compliant with EU regulations with EBS-E (2S2M), without connecting lines to tractor unit Steel Construction: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * Premium and durable corrosion protection of the standard shot-blasted welded frame by a two-component (2K) zinc dust primer * High-quality single-color topcoat (2K) in RAL 3002 carmine red * Rims in silver * Rear section metallised and painted in RAL 9010 (pure white) Including the following additional equipment: * Yellow-red air couplings on galvanised front connector bar * 4 wheel chocks with holders * 2" king pin * Yellow reflective tape compliant with EU-standard on sides, extension and trailer rear * European reflector boards (red-yellow) on rear of trailer * Loading platform with approx. 30 mm thick wooden floor encased in Omega profiles * 10 pairs of stake pockets for insertable stanchions approx. 100 x 50 mm in the outer frame of the loading platform * Storage for up to 9 pairs of insertable stanchions approx. 100 x 50 mm bolted to the inside of the front wall * 1 spare wheel holder under the loading platform on the left in the driving direction, without spare wheel * One mudflap at the rear of the trailer * Manual and documentation on USB stick * Bracket for rotating beacon at the rear of the trailer * On gooseneck and rear panel, left and right, one holder each for warning signs, including socket * Speed stickers 80 km/h, rear and both sides * Load gauge for axle load determination including load chart * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container pockets on loading platform, for 1x 20' container, 2x 20' containers or 1x 40' container flush with the rear * INOX toolbox, approx. 600 x 350 x 600 mm, under the platform on the left in the driving direction * 4 pairs of longitudinal stake pocket rails for 80 x 50 mm insertable stanchions mounted on the loading platform * Lift axle on the front axle with control via TEBS E depending on current axle load and loading condition * 2 LED reversing lights mounted on rear panel * HRM metallisation (High Resistance Metallisation)

Condition: new, maximum load weight: 38,140 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment. Full equipment details available on request. Gooseneck: - Gooseneck with front corners chamfered approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - Between 1st and 2nd axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized cover over wheel recesses (width approx. 670 mm – max. point load 5 t / pc.) - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame for attaching tie-down straps (LC 2,000 daN) Landing legs: - JOST landing legs (manual) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: - Tyres 235/75 R17.5 3PMSF, make at our discretion Bledpfx Apew Tpq Doreh - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transfer to the towing vehicle via standardised EBS interface as per ISO 11992 - For correct display, the towing vehicle must be able to receive and display this data Axles: - BPW axles and suspension, 2 axles rigid, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reverse lockout activated automatically when reversing and manually - Air suspension with lifting and lowering valve. Axle tools Braking system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without piping to the tractor unit Electrical system: - Electrical system per EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets, according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel structure made of high-strength fine-grained steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure automatically shot-blasted after welding in a wheel-blasting system - Second shot-blasting with corundum for optimum coating adhesion - HRM metallization of entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final painting with 2 layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, rear section metallized and painted in RAL 9010 Pure White - Metallic finish not available - Paint structure tested in salt spray test according to ISO 9227-NSS - Internal cavities sealed with special wax Including the following accessories: - On the gooseneck and rear, left and right, one holder for warning signs each, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch king pin - Galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection bar - Galvanized folding supports under the inclination at the rear of the loading area - A hardwood crash protection strip at the rear wall from gooseneck to the loading area - 1 pair of recessed lashing rings along the central beam at the rear inclination (LC 10,000 daN) - Aluminium drop sides and tailgate on the gooseneck

Condition: new, maximum load weight: 33,865 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete range of vehicles, including those available for immediate delivery or on short notice, on our website. Below is an excerpt from the specification. The full equipment list is available upon request. Gooseneck: * Gooseneck with front corners chamfered approx. 45° and a rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Load area: * Double extendable design with rear bevel approx. 500 mm x 8° * 6 pairs of folding external lashing rings (LC 5,000 daN) * 4 pairs of folding external lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Hardwood flooring approx. 48 mm thick, over axles with checker plate covering * Cut-outs in the external frame of the loading platform for attaching tie-down straps (LC 2,000 daN) Axles: * BPW axles and suspension, all axles forced-steered hydro-mechanically * Design axle load: 12,000 kg each * Air suspension with lift and lower valve * Axle tools included Tyres: * 245/70 R 17.5, load index (146/146 F) * Brand of our choice Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Braking system: * Braking system according to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Paintwork: First-class and durable corrosion protection * High-quality, one-colour 2-component (2K) topcoat in RAL 3002 carmine red * Rear section metallized and coated in RAL 9010 (pure white) Steel Structure: Steel construction from high-strength fine grain steels. * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Bljdpfow Tprzex Aproh Electrical system: * Electrical system according to EU regulations * 24 Volt lighting ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets, compliant with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Including the following additional equipment: * 2-inch kingpin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings at the galvanized front connection strip * Spare wheel carrier in front of the front wall * Electro-hydraulic unit * Rear and front steering via cable remote control with push-buttons, with single-track monitoring of the axles (without installation in the tractor unit) * Mount at the rear of the gooseneck for aluminum loading ramps * Removable aluminum ramp hanging rail at the rear of the vehicle * Galvanized folding supports beneath the slope of the load area * On the gooseneck: plug-in aluminum side boards and rear board, approx. 2,440 x 400 mm (L x H) * The rear galvanized stanchions are removable (body length approx. 2,560 mm) * One galvanized toolbox, integrated in the chamfered gooseneck * 4 pairs of WADER container pockets in the loading area for one 20', two 20', one 40' or one 45' container * 8 pairs of stanchion pockets (approx. 100 x 50 mm) in the external frame of the loading platform * Galvanized extensions, extendable by approx. 230 mm per side * Adjustable hanging rails for aluminum ramps at the rear of the vehicle * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * Central lubrication system with 2 BEKAMAX (Pico) pumps, filled with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM Metallization (High Resistance Metallisa

Condition: new, maximum load weight: 37,820 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. Gooseneck: - Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood floor covering approx. 30 mm thick Loading area: - 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) - Wheel recesses with square climbing slats approx. 15 x 15 mm and widenings in the lower section - Between the 1st and 2nd axles, a pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) – max. point load approx. 5 t/each - Recess in the chamfer and extending into the loading area for receiving the excavator bucket arm (approx. 2,900 x 750 x 210/290 mm (L x W x H)) - 1 pair of lashing rings, horizontal, at the front of the loading area (LC 10,000 daN) - 5 pairs of flip-out lashing rings (LC 5,000 daN) - 3 pairs of flip-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) One-piece Steel Ramps: - One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering - Ramp with hydraulic lifting mechanism, hydraulically adjustable - Maximum load per pair: 40,000 kg - In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not count towards the vehicle length in the driving position Landing gears: - JOST landing gears (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: - BPW axles and suspension, 2 fixed axles, 1 trailing steering axle - Technical axle load: 12,000 kg each - Electromagnetic reverse lock, activated via reverse gear and manually Bsdpew Tpqwefx Aprelh - Air suspension with lift and lower valve - Axle tool kit Tyres: - Tyres 235/75 R 17.5 3PMSF – manufacturer of our choice - TPMS tyre pressure monitoring system in accordance with ECE R 141. The data transmission to the truck is via standardized EBS interface according to ISO 11992. For correct display, the truck must be able to transmit and display this data Braking system: - WABCO braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction: - Steel structure made of high-tensile fine-grain steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations - Lighting 24 volts ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - Complete steel structure automatically shot-blasted with blasting wheel machine after welding - Second shot-blasting using corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure maximum corrosion protection - Final painting with 2 coats of two-component topcoat, single color in RAL 3002 Carmine Red, according to the RAL system 841GL - Rims in silver - Rear section metallized and in RAL 9010 (continuation see ori

Condition: new, maximum load weight: 39,720 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Sample equipment features. Full specification upon request. Gooseneck * With beveled front corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Loading Platform Loading platform in extendable design * 5 pairs of fold-out outer lashing rings (LC 5,000 daN) * 3 pairs of fold-out outer lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Recesses in the outer frame of the loading platform for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over axles with chequer plate covering Bsdpfx Asu Sd U Usprolh Landing Gear * JOST (mechanical) with 2-speed gearbox, approx. 24 t lift capacity (approx. 50 t test load) Axles * BPW axles: 2 fixed axles, 2 steering axles, drum brakes * Air suspension with lift/lower function * Self-steering axle with electro-magnetic reverse lock, activated via reverse gear or manually * Tires: 205/65 R 17.5 Brake System * Wabco brake system in accordance with EU directives with EBS-E (4S3M), without interconnecting lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork * First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) top coat, single-color, RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories Included * 2-inch king pin * Galvanized front steel bulkhead approx. 400 mm high * Spare wheel holder in front of bulkhead * Yellow-red air couplings on galvanized connector bar front * 4 wheel chocks with holder at bulkhead * Bracket at rear of gooseneck for aluminum loading ramps * Galvanized folding supports under inclined edge of loading platform * Holder for beacon at rear of trailer * Yellow reflective tape on sides, extension, and rear in accordance with EU regulations * Brackets for warning signs with socket on both sides at the gooseneck and rear panel * TPMS tire pressure monitoring system per ECE R 141. Data transmission to the tractor unit via standardized EBS interface according to ISO 11992; for correct display, the tractor unit must support data transmission and display * Plug-in aluminum side walls and tailgate on gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized stakes are removable (body length approx. 2,560 mm) * Galvanized toolbox, integrated in gooseneck slope * 6 pairs of WADER container locks in loading platform, for 1 x 20' container, 2 x 20' containers or 1 x 40' container * Sliding mounting rails for aluminum ramps at rear of vehicle * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm, in the outer frame of the loading platform * Galvanized cross bracket under the loading platform * Galvanized extendable widenings, extendable approx. 230 mm per side * Lift axle on front axle, controlled via TEBS E according to current axle load and load status * 5 pairs of recessed lashing rings along the central beam (LC 5,000 daN)

Condition: new, maximum load weight: 52,810 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of immediately and soon available vehicles on our website. Excerpt from the equipment list. Full specifications available on request. Cargo area: * Cargo area with approx. 30 mm thick hardwood floor * 10 pairs of folding external lashing rings (LC 10,000 daN) Landing legs: * Hydraulic landing legs TPMS: * TPMS tire pressure monitoring system compliant with ECE R 141. Data transmission to the tractor unit is via the standardized EBS interface according to ISO 11992. For correct display, the tractor must be capable of transmitting and displaying these data. Axles and suspension: * BPW axles, technical capacity 12,000 kg each, first axle fixed, all others hydro-mechanically forced-steered, mounted on turntables * Air-suspended with lift and lower valve * Axle toolkit Tires: * Tires 445/65 R 22.5 169 K Electrical system: * Electrical system in accordance with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets * Connections according to standards. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Brake system: * Wabco brake system compliant with EU regulations, with EBS-E (4S3M), without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield point 355MPa), S690QL/S700MC (yield point 690MPa) Painting: * Complete steel structure automatically shot-blasted after welding using a shot-blasting machine * Secondary blasting with corundum for optimal adhesion of the coating system * Final painting with 2 coats of 2K topcoat, single color in RAL 1007 Narcissus Yellow according to RAL system 841GL * Rear section metallized and painted in RAL 9010 Pure White * Wheels in Silver Grey * Paint structure tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Including accessories: * Cargo area with approx. 30 mm thick hardwood floor * 2-inch king pin * One galvanized steel front wall (EN12642-XL), approx. 1,200 mm high * Yellow-red air couplings on the galvanized front connection strip * On the gooseneck and rear panel left and right, each with a bracket for warning signs including socket * Rear steering from the front and rear by cable remote control via push buttons, with single-track control of the axles (without installation in the tractor unit) * Electro-hydraulic unit * 12 pairs of stake pockets for approx. 100 x 50 mm stakes in the outer frame of the cargo area Blsdpfxjxttc Ao Apreh * Load manometer for determining axle loads including load diagram * Lift axle on the front axle, controlled by TEBS E * 5 pairs of crosswise stake pocket rails on the cargo area, for approx. 100 x 50 mm stakes * One INOX toolbox 1,200 x 460 x 550 mm mounted at the front left under the cargo area (in direction of travel) * 1 shunting coupling with reinforcement bolted to the rear cross member * BEKAMAX (Pico) automatic central lubrication system with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum)

Condition: used, Year of construction: 2024, lifting height: 4,000 mm, fuel type: diesel, motor manufacturer: Cummins-Diesel, Lifting capacity: 16.000 kg Bjdpfjydm Dpex Aprelh Please contact Sales Team for more information

Condition: used, Year of construction: 2007, operating hours: 19,489 h, lifting height: 4,500 mm, fuel type: diesel, motor manufacturer: Volvo-Diesel, Lifting capacity: 12.000 kg Please contact Sales Team for more information Bsdpfxjydm Aro Aprslh

Condition: new, maximum load weight: 28,840 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 9,660 mm, loading space width: 2,250 mm, loading space height: 2,350 mm, loading space volume: 50 m³, Equipment: ABS, Example: Bedpohfiqcsfx Aprolh STRONG & LIGHT, now also available for heavy-duty use, from 40 m³ loading volume and 6,600 kg. STRONG & LIGHT, now also available for heavy-duty use, from 40m³ loading volume and 6,600kg ----Example: high-quality aluminum chassis with high-strength steel trough, REAL 7,160 KG, Chassis with 3x9t axles DCA, with 430mm disc brake, 6x steel rims, 1st axle as lift axle with starting aid, aluminum drop-lift supports (can be uncoupled when loaded), foldable underrun protection, digital loading pressure gauge as axle load indication, tool box, lean-to ladder, Trough made of HB450 steel sheets, floor 5mm, side walls and rear doors made of 4mm HB450 steel sheets, wing doors 1/2 - 1/2 with a grain slider on the right, subsequent unlocking of the rear doors, doors sealed with round steel (sealing with rubber seal possible - mud-proof), roll-up tarpaulin with a pipe in the middle, aluminum mudguard to protect the roof tarpaulin during loading, platform standing on the frame, EdBro tipping cylinder with long cover, loading edge = 3,650mm, (some of the vehicles shown contain special equipment) ----Other equipment points and a detailed vehicle offer are available on request, various loading volumes, vehicle lengths and heights possible, Paintwork and equipment according to customer requirements +500¤ transfer costs ?Offers and images are subject to change ?

Condition: used, axle configuration: 3 axles, first registration: 02/2000, color: other, Year of construction: 2000, Empty weight: 8.900 kg Axle 1: left 6 mm right 6 mm Axle 2: left 8 mm right 8 mm Axle 3: left 8 mm right 8 mm Bedpeyff Trsfx Aprelh We have the possibility to stack trailers! 

Condition: used, machine/vehicle number: XL962000050002174, axle configuration: 2 axles, first registration: 09/2005, color: other, Year of construction: 2005, Please contact us for more information. Blodpfx Aoxamvveprjh

Condition: used, machine/vehicle number: XL9MCS218BD074047, axle configuration: 2 axles, first registration: 04/2011, total length: 9,710 mm, total width: 2,420 mm, wheelbase: 7,120 mm, color: other, Year of construction: 2011, Empty weight: 3.400 kg Carrying capacity: 14.600 kg GVW: 18.000 kg Bledpfx Ajx Rzyajpreh Registration number: 16-WH-BS

Condition: used, color: other, Year of construction: 2000, We have a stock of >100 axles. Please contact us if you can't find what you are looking for. Blsdpfxjp T Tcwj Aprjh

Condition: used, color: other, Year of construction: 2000, Serial number: WLN/S5310/QMXD Bsdpfx Apjpygxyerolh We have a stock of >100 axles. Please contact us if you can't find what you are looking for.

Condition: used, axle configuration: 3 axles, first registration: 12/2007, color: other, Year of construction: 2007, Empty weight: 7.050 kg Axle 1: left 6 mm right 6 mm Blsdpfxjw Uh N Ue Aprjh Axle 2: left 8 mm right 8 mm Axle 3: left 6 mm right 6 mm We have the possibility to stack trailers!