Used Glue Press for sale (13,239)

Condition: ready for operation (used), Year of construction: 1991, functionality: fully functional, machine/vehicle number: 4712, pressing force: 120 t, cylinder diameter: 90 mm, number of cylinders: 6, pressing speed: 200 mm/s, TECHNICAL DETAILS Kedpjyuxh Isfx Abcsww Maximum pressure: 120 t Pressing area dimensions: 2,500 x 1,300 mm Pressing height: 200 mm Number of cylinders: 6 Cylinder diameter: 90 mm Pressing speed: 12 m/min EQUIPMENT Complete line with: Loading system Gluing machine Destacker High-frequency cabinet (offered separately)

Condition: ready for operation (used), Year of construction: 1986, functionality: limited functionality, machine/vehicle number: 97862034, installation height: 255 mm, sheet thickness (max.): 5 mm, working width: 180 mm, pressing force: 100 t, stroke length: 50 mm, TECHNICAL DETAILS Press force: 100 t Total force: 1,000 kN Ring tooth force: 40 - 310 kN Counterholder force: 10 - 270 kN Max. material width: 180 mm Max. material thickness: 5 mm Stroke rate (min.): 20 rpm Stroke rate (max.): 80 rpm Stroke: 50 mm Feed unit Max. strip thickness: 5 mm Kwjdpfjytcd Rsx Abcew Max. strip width: 180 mm Max. feed length per ram stroke: 999.9 mm Tensile force per feed (starting force): 6 kN Clamping force: max. 19 kN Max. feed height adjustment: +40 mm Max. distance between feed rollers: 20 mm Resolution, related to rollers: 0.1 mm MACHINE DETAILS Input voltage: 400 V Input frequency: 50 Hz Connected load: 13.5 kW Pump power: 3 kW Motor power: 3 kW Air connection: 6 bar Height adjustment type: hydraulic Dimensions & weight Dimensions (H x W x D): 2,420 x 2,325 x 1,665 mm Installation height: 255 mm Weight: approx. 6 t Year of last overhaul: 1997 EQUIPMENT Decoiler unit Two sets of tools Note: Further technical data for the machine can be found in the attached operating manual. The seller has repeatedly experienced issues with the processing and blow-off cycle. As a result, parts were not cleared out and the machine was stopped for safety reasons. However, the seller assumes this is merely a matter of adjustment. The seller recommends an overhaul of the control system in the long term.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 630213235, The machine is in like-new condition! The technical data is provided by the manufacturer. The seller assumes no liability for its accuracy! TECHNICAL DETAILS Press force: 594 kN / 60 t Specific pressing force: 45 N/cm² Cycle time in idle mode: 25 s Idle press capacity (theoretical): 32.5 m³/h Filling height: 1,115 mm Kedjyqw Sqspfx Abceww Feed opening dimensions: 1,195 x 650 mm Bale dimensions: 1,200 x 1,200 x 1,100 mm Max. bale weight: 550 kg Material to be pressed: Film, mixed paper, cardboard, punching waste MACHINE DETAILS Drive power: 4 kW Voltage: 400 V Frequency: 50 Hz Door design: Sliding door Door lock: Hydraulic Type of loading: Manual Consumables: Wire, looped wire Dimensions & Weight Dimensions (L x W x H): 1,780 x 1,568 x 2,985 mm Machine weight: 2,450 kg EQUIPMENT HSM TCS (TorsionControlSystem) for monitoring the inclination of the press plate Automatic start of the pressing process

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 721359, color channels: CMYK, paper weight (min.): 50 g/m², paper weight (max.): 400 g/m², paper width (max.): 36 mm, paper height (max.): 52 mm, Heidelberg Printmaster GTO 52-4 Offset Printing Machine (2006) For sale: Heidelberg Printmaster GTO 52-4, a reliable and high-quality 4-color offset printing machine manufactured in Germany. Model: GTO 52-4 Year: 2006 Serial Number: 721359 Configuration: 4-color (CMYK) Location: Azerbaijan Condition: Machine is in excellent working condition. Fully operational and well maintained. All new photos and videos are available. The machine is ready for inspection and testing at any time. Technical Specifications: Format: B3 (max sheet size 360 × 520 mm) Max print area: approx. 340 × 505 mm Speed: up to 8,000 sheets per hour Paper thickness range: approx. 0.03 – 0.4 mm Equipment and Features: Alcolor dampening system Manual plate clamping system Heidelberg inking unit with oscillating rollers Stream feeder with double-sheet control High pile delivery Powder spray unit Mechanical control system (simple, reliable, low maintenance) ink remote control Classic Center, single sheet feeder photoelectron. double sheet control, DDS film dampenings cooling unit Technotrans Alpha, quick plate clamping bars dry sprayer, + version Kwjdpfjyvdbpsx Abcow Applications: Suitable for a wide range of commercial printing jobs including brochures, flyers, catalogs, business cards and other promotional materials.

Condition: like new (used), Year of construction: 2017, functionality: fully functional, Training school display unit VERY VERY seldom use For demo only, like new Ksdpfx Aeyunphsbceww 1) Amada TP45FX 2) PATEC 110ton press with recoiler

Condition: like new (used), Year of construction: 1985, operating hours: 200 h, functionality: limited functionality, machine/vehicle number: 38754, pressing force: 250 t, This plate bending machine was installed new in 1989 and was used for 200 Hrs and never used ever since. The mechanical parts are fully functional and are in perfect condition but the electrical board needs fixing. Force: 250 mp (metric tons) Working Surface Length: 5600 mm Kwodjykl Iajpfx Abcsw Working Surface Width: 400 mm Working Surface Height: 100 mm Weight: Approximately 37,000 kg Press Sizes (LxHxW): 5700 x 3150 x 5200 mm

Condition: new, functionality: fully functional, Year of construction: 2025, machine/vehicle number: 1235, controller manufacturer: Germany Beckhoff, working width: 1,200 mm, bending angle (max.): 90 °, sheet thickness steel (max.): 4 mm, sheet thickness aluminum (max.): 6 mm, total length: 1,685 mm, total width: 1,262 mm, type of input current: three-phase, workpiece length (max.): 1,200 mm, workpiece height (max.): 430 mm, nominal power (apparent): 3 kVA, number of spindles: 6, opening width: 400 mm, - Germany Beckhoff System, Closed-loop control, High bending accuracy. - Italy GIVI MEASURE precision linear encoder. -High strength machine body after heat-treated. - No need to change bending tool. - The Blank-holder tool can automatically change the length basic on the sheet length. - Multilateral automatic continuous bending. -Automatic programming software can finish all the process - Automatically check and optimize. the process -All servo motor control, fast and energy saving - Automatically control pressing force. Kwjdpjwfwkqefx Abcow

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: 1032, warranty duration: 12 months, total width: 2,300 mm, total length: 1,685 mm, bending angle (max.): 90 °, working width: 3,200 mm, workpiece length (max.): 3,200 mm, workpiece height (max.): 370 mm, nominal power (apparent): 4 kVA, number of spindles: 4, sheet thickness aluminum (max.): 6 mm, sheet thickness steel (max.): 4 mm, type of input current: three-phase, -Complete machine frame processing -Double-cylinder electro-hydraulic synchronous control Ksdpfx Aswfwkwebcjww -A variety of electro-hydraulic CNC systems are optional -Mechanical compensation -Segmented mold -High-precision back gauge structure -Scalable number of axes

Condition: as good as new (ex-display), Year of construction: 2025, Tool testing press 150to installation height 1000mm stroke 600mm ram plate 1500mm x 1000mm table surface 1500mm x 1000mm Front light curtain Kwjdpfx Askw Rbasbcew Siemem control Weight 12,5to

Condition: like new (used), Heidelberg GTOZ-S52 offset printing machine The machine is ready to work, very good condition, purchased from small printing house. Technical data: Kedpoywgyljfx Abcjww Format: 36x52cm 2 printing units Weight: 3000kg Power supply: 400V Year of production: 1994 Baldwin alcohol dampening Control panel Documentation and additional elements included.

Condition: good (used), CMC Italia Q Finish Crater 20 Book Press Book press with groove cutter and heated platens. Manufactured by CMC, Italy. Technical specifications: Maximum format: 420 x 500 x 80 mm Weight: 420 kg Kjdpfx Abjywdtvscjww Pressure: 5000 kg Built-in hydraulic unit. Automatic book feed. Automatic format detection. 380V power supply + compressed air.

Condition: good (used), Nagel Citoborma 290AB Paper Drill The machine is 100% functional and ready to use. Robust construction – weighs 200 kg. This is the current Citoborma drill model in production. 400V power supply. Two drilling heads with adjustable spacing ranging from 45-170 mm. Drill diameter: 2-20 mm. Stack height: 60 mm. Controlled by an electric foot pedal. Waste is directed to an external sleeve. Kodpfx Absywdqzeceww The drill table is adjustable in every direction (sides, front/back) and has stops for setting the drill spacing (non-standard drilling). Additionally, a special module for standard spacings is installed in the table. Furthermore, the table has two movable margins. The drill has an automatically released table lock after each cycle, allowing the table to be moved to the next position. The set includes drills, tools and instructions.

Condition: good (used), Nagel Citoborma 490 Paper Drill This is the largest Citoborma drill currently in production. Very good condition, ready for production. The machine has 4 drilling heads. Drilling waste is discharged into a basket located at the rear of the machine. The machine is operated using a foot pedal or two-handed buttons. Kwsdpfxeywdn Tj Abcow Each head has a separate up/down adjustment, allowing for the use of drill bits of different lengths. The set includes spare drill bits, tools, and an instruction manual. Technical specifications: Number of drilling heads: 4 (each head can be quickly removed) Maximum stack height: 60 mm Drill bit size: 2-10 mm Adjustable spacing: 45 – 425 mm Two drilling speeds 380V power supply Weight: 365 kg Made in Germany.

Condition: good (used), Sperr & Lechner SL II A-100 Hydraulic Bookbinding Press Kwsdjywdmvepfx Abcjw Ready for operation. The machine is like new. The press has a built-in hydraulic unit. Piston rod area (main plate): 580x440mm Single piston rod area: 440x280mm. Irreplaceable in bookbinding for the production of books, pads, etc. Weight: 600kg. 380V power supply. Made in Germany.

Condition: good (used), Nagel Citoborma 480AB Paper Drill This machine is in very good condition. It has four drilling heads. Technical specifications: Drill bit distance: 45-285 mm Drill diameter: 2-20 mm Stack height: 60 mm Weight: 275 kg Automatic drilling cycle, controlled by a foot pedal and manual buttons. Sturdy construction on a pedestal. The drill table is adjustable in all planes. This is one of the newest Citoborma models. Includes operating tools, instructions, and a new cutting stick and drill bits. Kwedpfx Aoywdmpobcow

Condition: like new (used), Year of construction: 2014, 4 meter width Ksdpjlqwvkefx Abcsww Nominal pressure 1250 kN CNC Back Gauge Quick Change Tooling

Condition: used, Year of construction: 2015, Eight-color offset printing press with perfecting device for double-sided printing, sheet format 75 x 106 cm, model HEIDELBERG SPEEDMASTER XL 106-8-P Kwjdpeyv A Hfofx Abcjw Year of manufacture: 2015 Impressions: 230 million

Condition: as good as new (ex-display), Year of construction: 2025, Hydraulic SPS press 100to (1.000KN) pressing force Kedpjnp Ndhefx Abcsww Siemens SPS1200 series Screen 10" Beijer stroke 400mm table top 790mm x 600mm Speed forward 110mm Speed return 140mm Light curtain Sick Remote maintenance module built in Rexroth hydraulics with cooler Available from week 46 fairground Stuttgart Modifications can be realized after request if necessary

Condition: excellent (used), functionality: fully functional, Double-sided glue spreader OSAMA S2R-1000 Working width: 1000 mm Min./max. pass-through height: 0-90 mm Diameter of applicator rollers: 185 mm Feed speed: 18 m/min Kodpfx Ajyvpkwebcsww Motor: 0.37 kW

Condition: new, Year of construction: 2025, Delivery ex works Turkey Kwodpfx Asgu N Alebcew Bending length (A): 3050 mm Press force: 170 tons Sheet thickness 42kgf / mm: 8 mm Sheet thickness 72kgf / mm: 4 mm Upper tool: 1260 Top Tool 85 ° Lower tool: 50, 35, 22, 16 Distance between columns (B): 2550 mm Forward speed: 130 mm / s Working speed: 8 mm / s Retraction speed: 120 mm / s Crowning: manual (CNC-motorized available for an extra charge) X-axis travel: 750 mm X-axis speed: 250 mm / s Backgauge fingers: 2 pieces Front support arms: 2 pieces Oil tank capacity: 180 liters Main motor power: 11 kW Stroke length (C): 265 mm Installation height (D): 450 mm Projection stand (E): 410 mm Table height (F): 870 mm Table width (G): 170 mm Length (L): 4200 mm Height (H): 2800 mm Width (W): 2200 mm Weight: approx. 7500 kg Cybelec Cybtouch 12 2D Graphic CNC control 3 axes (Y1, Y2, X) expandable with optional R+Z-Axis Eurostamp 2067 lower tool (V: 50, 35, 22, 16) Eurostamp 1260 upper tool 85 ° Narrow table All-steel welded construction Promecam quick clamping system CNC-controlled motorized backgauge (X: 750 mm) Adjustable backgauge fingers Inch and metric system can be selected Ground and chrome-plated cylinders Swiveling control panel Foot control with anti-panic stop & emergency shutdown Lateral protective grille (secured with limit switch) Light curtain on the back of the machine (900 mm) DSP laser finger protection system at the front (CE) BOSCH / REXROTH or HOERBIGER / HAWE hydraulic system BOSCH / REXROTH or ECKERLE hydraulic pump Slidable front support arms (2 pieces) Electronics unit from: SIEMENS, SCHNEIDER, DELTA, ABB, OMRON 380 V 50 Hz Painting: RAL 7035, RAL 5015 Optional special accessories available at an additional cost: -CNC-controlled R-axis (250 mm) -CNC motorized crowning -Servo driven motors backgauge system for X + R axis (Mitsubishi) -Painting in special colors on customer request Documentation in German or English CE conformity

Condition: new, Year of construction: 2025, Delivery ex works Turkey Bending length (A): 2550 mm Press force: 135 tons Sheet thickness 42kgf / mm: 8 mm Sheet thickness 72kgf / mm: 4 mm Upper tool: 1260 Top Tool 85 ° Lower tool: 50, 35, 22, 16 Distance between columns (B): 2100 mm Forward speed: 120 mm / s Working speed: 8 mm / s Retraction speed: 120 mm / s Crowning: manual (CNC-motorized available for an extra charge) X-axis travel: 750 mm X-axis speed: 250 mm / s Backgauge fingers: 2 pieces Front support arms: 2 pieces Oil tank capacity: 150 liters Main motor power: 7.5 kW Stroke length (C): 265 mm Installation height (D): 450 mm Projection stand (E): 410 mm Table height (F): 850 mm Table width (G): 110 mm Length (L): 2950 mm Height (H): 2200 mm Width (W): 1500 mm Weight: approx. 6000 kg Kodpfxogu Nzre Abcjww Cybelec Cybtouch 12 2D Graphic CNC control 3 axes (Y1, Y2, X) expandable with optional R+Z-Axis Eurostamp 2067 lower tool (V: 50, 35, 22, 16) Eurostamp 1260 upper tool 85 ° Narrow table All-steel welded construction Promecam quick clamping system CNC-controlled motorized backgauge (X: 750 mm) Adjustable backgauge fingers Inch and metric system can be selected Ground and chrome-plated cylinders Swiveling control panel Foot control with anti-panic stop & emergency shutdown Lateral protective grille (secured with limit switch) Light curtain on the back of the machine (900 mm) DSP laser finger protection system at the front (CE) BOSCH / REXROTH or HOERBIGER / HAWE hydraulic system BOSCH / REXROTH or ECKERLE hydraulic pump Slidable front support arms (2 pieces) Electronics unit from: SIEMENS, SCHNEIDER, DELTA, ABB, OMRON 380 V 50 Hz Painting: RAL 7035, RAL 5015 Optional special accessories available at an additional cost: -CNC-controlled R-axis (250 mm) -CNC motorized crowning -Servo driven motors backgauge system for X + R axis (Mitsubishi) -Painting in special colors on customer request Documentation in German or English CE conformity

Condition: used, functionality: fully functional, Knuckle joint / coining presses CINCINNATI HME K-360 tons (3 units) K-600 tons (1 unit) Cincinnati HME K360 360 Tons capacity Stroke 2.125" Speed 90-200 SPM Main Motor 22 kW Maximum Coin Diameter 34 mm Maximum Coin Thickness 3.5 mm Cincinnati HME K600 600 Ton Capacity, 4.5'' Stroke, 25 Strokes per min, Kwodsypathspfx Abcsw 17.5'' Shut Height (SDAU), 9/16'' Top Tool Adjustment

Condition: as good as new (ex-display), Year of construction: 2021, total width: 1,618 mm, total length: 1,830 mm, total height: 2,400 mm, overall weight: 5,000 kg, type of input current: three-phase, input current: 81 A, input frequency: 60 Hz, opening width: 100 mm, operating temperature: 140 °C, cylinder diameter: 65 mm, Shelf press for veneer , plywood , MDF, particle board, solid wood, etc. Manufacturer : JOOS Model: HPS 20 year of production 2021 Total pressure force : 200 kN 4 cylinders ⌀ 65 mm x 400 mm Maximum hydraulic working pressure : 150 bar Pressure : 2.0 daN / cm2 5 heating plates size : 1000mm x 1000mm Operating temperature : 0℃ - 140℃. Infinitely adjustable temperature. Timer to set the working time , after the set time the press automatically opens. Heating power - 5 x 12 kW Kwsdot Eq E Sopfx Abcjw Total power - 64 kW (81A , 60Hz) Weight - 5000 kg Press new - never used Full technical documentation included.

Condition: good (used), Nagel Citoborma 111 Paper Drill This machine is 100% functional and in very good condition. Kedpfx Absyur E Hocjww The drill table is adjustable in all directions (sides, front/back). It has stops for setting the drilling spacing. Sturdy construction – weighs 35 kg. This is one of the newest Citoborma drill models, currently in production. 230V power supply Drill bit diameter: 2-9 mm Stack height: 50 mm Includes drill bits, a new cutting stick, and instructions. Made in Germany.

Condition: good (used), Oropress Hot Stamping Press This machine is in very good condition and ready to use. Kwodpfxjyur Ege Abcjw This machine is from the popular Oropress hot stamping machine manufacturer, manufactured in Germany. Description The Oropress hot stamping press is a hot stamping and embossing press for paper and plastics. It’s a useful device in any advertising agency or digital printing house. The manual press is powered by only 230V. A powerful press with adjustable pressure ensures repeatability and very high pressure between the die and the material. The machine features a worktop with a sliding function, adjustable embossing depth, and a hot plate with a thermostat. Specifications: Heating temperature adjustment Hot plate pressure mechanism: mechanical Press force: 1000 kg Power consumption: 500 W Power supply: 230 V Machine weight: 100 kg Plate size: 130 x 100 mm.