Used Hole Washers for sale (6,172)

Condition: used, Year of construction: 1980, Number of drill spindles: 23 Pitch: 32 mm Drill bit holder: Screw-in thread Operation: Foot pedal Drilling direction: From above and from the front Swivel: Pneumatic Maximum throughput width: 720 mm Number of material clamps: 2 Type of material clamping: Pneumatic Design: Mobile Stop system: For hole line and construction line Dimensions: 1300 x 1200 x 1700 mm Approx. weight: 365 kg Motor power: 2.2 kW Iiodpfewkir Djx Aabeh Storage location: Nattheim

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: 106840-11, overall weight: 35,000 kg, The drilling process of the deep hole drilling machine uses single-lip drilling. The BW250-T is a deep hole drilling and milling center with two separate spindles for deep hole drilling and milling operations. The machining units are equipped with an additional common travel axis, allowing even smaller workpieces to be machined from four sides on the clamping table without resetting. Drilling and Milling Unit Information: - Number of spindles: 1 drilling spindle and 1 milling spindle - Spindle speed infinitely variable: 0 - 5000 rpm - Spindle drive power: 17 kW at 100% duty cycle S1 operation - Torque: 260 Nm at 100% S1 operation - Max. drilling depth: 1500 mm (in one pass without repositioning) - Drilling diameter: 4 - 40 mm based on ST 60 Travel Paths: - X-axis travel: 2500 mm - Y-axis travel: 1500 mm - Z-axis travel: 850 mm - V-axis travel: 1000 mm Feed rates: - X-axis speed: 10000 mm/min - Y-axis speed: 10000 mm/min - Z-axis speed: 6000 mm/min Swivel Axis Setup for Drilling and Milling Unit: - The drilling and milling unit has a horizontal swivel range of -25° / +15° - 3x steady rests Fluid Information: - Coolant supply: deep hole drilling oil - Tank capacity: 2400 liters - 1x hinge belt chip conveyor - 1x hydraulic power unit and pneumatic unit/equipment - 1x central lubrication - 1x low-pressure pump: Pump output: 100 l/min Pump drive: 5.5 kW - 1x compact band filter: Filter output: 175 l/min For operations in: steel/non-ferrous metals - 1x radial piston pump with remote adjustment: Delivery rate: 2 - 120 l/min Pump drive: 11 kW - 1x oil mist extraction, Extraction capacity: 2400 m³/h Ijdpfxjxmh Ere Aaboih Tool magazine for conventional tools consisting of: - Tool change magazine with intermediate gripper - Tool holder HSK 63 - Max. permitted tool diameter: 127 mm - Max. permitted tool length: 400 mm - Tool storage spaces: 40 Clamping table with X-axis and NC rotary table: - Length/width: 1600 x 2000 mm - Useful load (centered): 15 t - Swing diameter for workpieces: 2800 mm Measuring Equipment - Tool breakage monitoring and length measurement of the BCM tools with automatic compensation in the control system Electrical Equipment Information: - 1x CNC control TNC 640 Failsafe Heidenhain - 1x drilling process monitoring - 1x remote maintenance - 1x dynamic collision monitoring - 1x handheld control device Connection Data: - Operating voltage: 3AC 400V ±10% - Frequency: 50 Hz - Control voltage: 24 V DC - Total connected load: 65 kW

Condition: used, Year of construction: 2000, Number of spindles in row: 11 Number of horizontal spindles: 3 Cup hinge boring head: yes, Blum Drill pitch: 32mm Power consumption: 2.2kW Ijdpfxjxc Hi Uj Aabjih Drilling unit: swiveling

Condition: used, Year of construction: 1984, Row and fitting boring machine, used machine, year of manufacture: 1984, condition: function-tested. Technical data: fully automatic pneumatic control with foot valve, boring unit 1.1 kW, speed 2800 rpm, boring stroke 0 – 55 mm, cross adjustable stop ruler 0 – 140 mm, working height 850 mm, required space without extension rail 1000 x 750 mm, compressed air connection 6 bar, weight approx. 70 kg. Includes various stops, boring heads, and drill bits. Location: Röllbach. Availability: Immediately. Iodsxdpkdopfx Aabsih

Condition: excellent (used), 10 x deep hole drills make Botek 3 pieces 6,5 x 320 mm Iiodpfx Ashl Awdoabsh 2 pieces 10,2 x 190 mm 3 pieces 10,4 x 250 mm 1 piece 1 x 11 x 350 mm 1 piece 11 x 270 mm Weight 1,5 kg

Condition: used, Year of construction: 2003, functionality: fully functional, machine/vehicle number: M307465, Chmer start hole EDM machine from 2003 Iiodpjxl Ub Djfx Aaboh

Condition: good (used), Year of construction: 1979, TBT T30-4-750/1000 -drilling diameter ~30 -drilling depth 750/extension ~1000 Ijdpfod Ri H Eex Aabeih -Tank -Pumps -loading equipment -Tailstock

Condition: good (used), functionality: fully functional, Row drilling machine SCHEER, 21 spindles, non-swiveling Iijdpfx Aoxlt R Reabeh

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, drilling depth: 1,000 mm, feed length X-axis: 900 mm, feed length Y-axis: 400 mm, feed length Z-axis: 300 mm, total length: 3,600 mm, total width: 3,300 mm, total height: 2,200 mm, workpiece weight (max.): 6,000 kg, overall weight: 6,500 kg, feed rate X-axis: 10,000 m/min, feed rate Y-axis: 10,000 m/min, feed rate Z-axis: 10,000 m/min, spindle speed (max.): 6,000 rpm, CNC HEIDENHAIN 530 ROTARY TABLE: Iedpfx Aewamdioabjih Work surface: 800 x 900 mm Fixing T-slots (quantity x width): 4 x 18 mm Maximum load allowed (rotating piece): 4.500 kg Maximum load allowed (fixed piece): 6.000 kg AXIS TRAVELS – WORK AREA: Transversal – deep V axis drilling: 1.000 mm Longitudinal X axis: 900 mm Vertical Y axis: 400 mm Auto piece approach Z axis: 300 mm ADVANCEMENTS: Rapid X, Y, Z axes: mm/min 10.000 WORKING CHARACTERISTICS IN DRILLING WITH "CANNON" TIPS: Maximum drilling depth: 1.000 mm Deep drilling spindle rotation speed: 6.000 rpm Drilling section, from solid – minimum drill Ø: 4 mm Drilling section, from solid – maximum drill Ø: 25 mm WORKING CHARACTERISTICS OF THE MILLING SPINDLE: Maximum rotation speed: 6.000 rpm Maximum thread (on C40 type steel): M 20 Maximum quill excursion (Z axis): 300 mm DIMENSIONS: Overall dimensions: 3.300 x 3.600 mm Height: 2.200 mm Total weight: 6.500 kg Machine complete with: • Instruction manuals and CE declaration

Condition: new, MSP – Manual Hand Spray Systems The MSP range of manual hand operated washing systems are made entirely from high quality stainless steel 304 and can be supplied high-pressure ump option achieving pressures of up to 60 bar. Thanks to a specially designed heavy-duty washing chamber the MSP range washes parts within a closed sealed envireonment ensuring the surrounding workplaces is kept clean, tidy and dry from pressurised water. Iedpfeh E Szmex Aabeih The MSP range is enviromentally friendly by utilising alkaline aqueous biodegradable detergents and allows for effective energy consumption using a foot pedal operation that oprates the pump only when pressed. This makes the MSP a very capability unit and a must have for any workshop enviroments cleaning heavy soiled contaminants.

Condition: used, Good day, We are offering used clamping beams from Erowa, System 3R and Becker Erodiertechnik. These clamping beams are suitable for wire erosion. The following parts are available: ER-017646 Iedpfx Aastk N E Ajbsih ER-017647 ER-017648 ER-021128 ER-021127 System 3R 3R-239-545-9911-V01 Becker erosion technology SB430-SB680 The clamping devices have signs of wear and are in very good technical condition. Individual acceptance also possible. Spare parts and accessories are available. Do you have any questions? Then we are at your disposal.

Condition: good (used), Year of construction: 1978, Punch, punching machine, punching device, hole punching machine, hole punch, copy punch, stop punch, hole punch, eccentric punch, row hole punch, punching machine, punching press -Manufacturer: Mubea, hole punch type KL 100 -Printing capacity: 100 tons -Punching capacity: see photo type plate -Thrust: 500 mm Iijdpfx Aswrn U Heabeh -Accessories: incl. see photos -Dimensions: 1460/880/H2100 mm -Weight: 2660 kg

Condition: good (used), -Drill through fair 5-30 mm - depth 750 ~ 900 mm - conversion to customer specification Iodpfxs Dcz De Aabjih

Condition: new, 3D perforated table 2400 x 1200 x 200mm, grid 100mm, plate thickness 20mm, hole diameter 28mm, Plan machined, very solid weight approx. 950 kg Iijdpfxsvm Dk Ij Aaboh With table base Price is without accessories

Condition: used, Hydraulic punch, punch frame for use with JOKA punching units type HP-S Hydraulic hole punch, hydraulic press for punching brackets Year of manufacture: approx. 1995 Pressing force: 5 tons Throat depth: 155 mm Stroke: approx. 20 mm Punching unit width: max. 54 mm Punching unit installation height: max. 220 mm Die holder: Ø 48 mm Motor output: 1.5 kW Power supply: 230 Volt, 50 Hz Iiedpjltrmuefx Aabeh - Suitable for universal use with JOKA SW 20 or SWD 20 punching units - Throat depth of punching units can be larger, can be pushed through to the rear - Stroke release via electric two-hand control - Hydraulic power pack HAWE, type HCW 4 / 2.5-B 1/400-1 - On subframe, mobile Required space (L x W x H): 1100 x 800 x 1450 mm Weight: approx. 200 kg Good condition

Condition: good (used), Year of construction: 2009, operating hours: 20,709 h, functionality: fully functional, machine/vehicle number: 106516-11, drilling depth: 1,200 mm, overall weight: 7,500 kg, For sale: A very well-equipped deep hole drilling machine from TBT, including various accessories. Drilling specifications: - Spindle 1: 5–18 mm; Spindle 2: 1–4 mm - Drilling depth: approx. 1200 mm with Ø8 mm using 3 steadies - Number of spindles: 2 - Spindle drive: Spindle 1: 1 x 4 kW; Spindle 2: 1 x 1.2 kW - Spindle speed: Spindle 1: 600–6000 rpm; Spindle 2: 2000–24000 rpm - Rapid traverse: 15,000 mm/min - Saddle stroke (nominal): 1800 mm - Coolant: Deep hole drilling oil Iodpfx Aajxgnhajbjih - Tank capacity: 1,100 liters - Operating voltage: 3AC 400V, 50Hz (Total connected load: 25 kW) Condition: Good, appropriate for its age Accessories: Includes drip tray and various drills On-site inspection is recommended!

Condition: excellent (used), Year of construction: 2019, 2 units in stock, both were only in use for a short contract. Loading basket 1600mm by 800mm Programmable controls. Ijdpfxeramamj Aabjih

Condition: good (used), functionality: fully functional, Year of construction: 2012, For sale: 1 piece used hole punch Manufacturer: Geka type: Puma 110 2HI Punching force: 110t Iijdpfjuihvzox Aabeh incl. documentation Dimensions see type plate Machine can be inspected in our warehouse in 09599 Freiberg.

Condition: not inspected (used), Year of construction: 1970, - Drilling diameter 5-30 mm Isdpfjxzz Hex Aabjih - Drilling depth 750 mm - Filter - Pump

Year of construction: 2000, condition: refurbished (used), LOCH Deep hole drilling machine TB 1-4/E-600/2 (reconditioned used machine) Working depth: max. 600 mm Working diameter: solid drilling 4 - 25 mm diameter in steel Number of spindles: 2 deep drilling spindles maintenance-free with lifetime grease lubrication Drilling spindle receptacle: Short taper according to DIN 55027, size 5 Center height: 250 mm Center distance: 203.2 mm Drilling system: single lip drilling Main drive: 2 x 5.5 kW drive power per spindle, steplessly adjustable by frequency regulated three-phase motor, power constant for the entire speed range. Speed range: 1000 - 6000 min-1 Feed rate: Through infinitely variable three-phase servo drive via recirculating ball screw and backlash-free preloaded nut. Feed range: 0 - 300 mm/min Extended feed range on request possible up to max. 6000 mm/min Rapid traverse: 6000 mm/min back and forth Coolant supply: Internal coolant supply through drill spindle via carbide mechanical seal. Spindle slide: Stable construction with mounted spindle spindle blocks in special construction, whereby the spindle bearings are provided with lifetime lubrication and are maintenance-free. Guide system: Machine bed with screwed-on, hardened and ground linear guides. Spindle slide moves via circulating rolling elements, feed vibration-free and without stick-slip effect. Drill bush support: Firmly connected to the substructure and with removable upper part for easy and quick change of drill bushings or the coolant supply units. Machine base: Strongly dimensioned welded construction, stress-relieved annealed. Clamping table: Table plate in special cast design firmly mounted on the substructure with T-slots, whereby the center groove is aligned with the drilling axis and serves as a guide groove for the accommodation of clamping elements. Control: SIEMENS Sinumerik 840 D (Retrofit) Workflow: Individual functions for setting up the machine via pushbutton control. Semi-automatic for manual loading via program start. Machine monitoring: With display of spindle speed, feed rate, drilling depth and coolant pressure. Protective device: The tool area of the machine is protected by a sliding door, which is electrically linked to the control, against unintentional and unauthorized opening during during the working process. Electrical equipment: All electric motors according to IEC standard. Separate electrical cabinet with all electrical necessary for the operation of the plant safety and control equipment. Machine operation from control panel conveniently located in the working area. Machine can be inspected and tested at any time if interested. Isdpfeikqrfex Aaboih MORE INFO ON REQUEST

Condition: used, Year of construction: 1979, Motorized high-performance hole punch MUBEA KL 30 Iijdev N Hrtjpfx Aaboh Punching capacity 30 t Hole diameter, steel 45 30 in 8 mm or 20 in 12 mm Throat 210 mm Machine dimensions L x W x H approx. 800 x 600 x 1400 mm Weight 330 kg • Mechanical foot release via cable pull • Hand finder • Adjustable hold-down device Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: new, Year of construction: 2025, functionality: fully functional, workpiece weight (max.): 170 kg, grinding spindle speed: 45,000 rpm, spindle speed (min.): 5,000 rpm, spindle speed (max.): 45,000 rpm, clamping diameter: 140 mm, clamping length: 1,100 mm, Workpiece Clamping Diameter : ø 3 – 140 mm Workpiece Length : 50 – 1.100 mm Centre Hole Diameter : ø 1 – 100 mm Workpiece Weight : max. 170 kg Center Hole Angle : 60 ° Accuracy : < 1 µm (Submicron accuracy) Spindle Speed : 5.000 – 45.000 rpm Grinding Cone Movements : 3+1 Rotation Orbital rotation Stroke movement +1 Workpeice rotation Quirlig Grinding Technique : Included (Cross-hatched grinding pattern) Grinding Process : Semi-Automatic, CNC Control Panel : Beckhoff CNC Movements : Z-Axis Indurstry 4.0 Compatibility : Available Semi-Auto Grinding Cone Dressing : Included Workpiece Rotation : Available (as a option) Dust Extraction And Filtration : Available (as a option) Sectors : Precision Grinding, Aviation, Automotive, Machinery etc. Benefits: Sub-micron Precision: Achieve sub-micron (< 1 µm) precision in grinding thanks to Swiss engineering and a robust machine design. Sustainable Reliability: Ensure reliable and sustainable processing. Cost Efficiency & High Productivity: Benefit from lower production costs and high productivity due to a short grinding process and reduced production times for subsequent processes (cylindrical grinding). Quirlig Grinding Technique: Experience an optimized grinding process with the Quirlig Grinding Technique. Properly ground center holes that have cross-hatched grinding pattern. The cross-hatched grinding pattern ensures that oil is retained when the workpiece is placed between the centers during the cylindrical grinding process, creating a micro oil layer. The micro oil layer prevents unwanted "dry running" during cylindrical grinding. Easy to Use CNC Control Panel: Benefit from very simple operation and grinding program recording with the Beckhoff control panel and Z-axis servo movement. Industry 4.0: Fully compatible with Industry 4.0 applications, thanks to the Beckhoff control panel. Low Maintenance Costs: Enjoy low maintenance costs throughout the machine's service life, thanks to Swiss-quality construction. Iodpfx Asgb Ec Hjabsih The Zentroflex SA-series center hole grinding machines are designed to deliver high-precision cylindrical grinding in the aviation, automotive, and machinery sectors. Additionally, the Zentroflex SA-series is the ideal solution for recovering parts distorted after heat treatment or for reducing cylindrical grinding costs. Z-Axis movement is provided by servo motor in CNC form. The part is loaded-unloaded and clamped manually. Settings are made from CNC control panel and grinding is started by pressing the start button. No other manual setting or control is made during grinding. Contact us for more details.

Condition: ready for operation (used), Pressure force: 10 tons Iisdpehtq Hfofx Aabjh Projection: 110 mm Required space: 300 x 170 x 680 mm Weight: 32kg

Year of construction: 2009, condition: ready for operation (used), A high-precision CNC drilling/reference hole machine Mach3 Lab with X-ray vision system is available. Travel X/Y: 700mm/800mm, max. panel dimensions X/Y: 700mm/700mm, min. panel dimensions X/Y: 300mm/200mm, panel thickness range: 0.3mm-6mm, Z-axis stroke: 40mm, spindle speed: 30000rpm, positioning accuracy: +/-0.003mm, transducer resolution: +/-0.001mm, X-ray range X/Y: 700mm/580mm, weight: approx. 2000kg. Documentation available. An on-site inspection is possible. Iijdpoxd Avgefx Aabeh

Condition: ready for operation (used), Drilling diameter 5 ~ 25 mm Drilling depth 1000 mm Ijdodgpltopfx Aabsih Headstock Tank pump Filter