Used Holz Her Verical Saw for sale (149)

Year of construction: 2015, condition: used, Used machine Year of manufacture: 2015 Special feature: was a demonstration unit from Holz-Her and only went into production operation with the machine in 2019 Equipment and technical data: Dsdswkbagopfx Addela - 30% to 50% space savings - Minimum gap between stacks (from 70 mm) = optimal space utilization - Panel damage excluded, panel separation control with weight measurement - Fully automatic operation (inbound/outbound storage) as well as automatic loading of the machine - Adaptable for all panel formats (1.2 to 5.6 m) depending on options - 90° rotation of panels - Low overall height of the manipulator - External dimensions: - Length: 8.5 m - Width: 7.5 m - Minimum panel size: 1.2 x 0.6 m - Maximum panel size: 3.2 x 2.1 m - Maximum lifting weight: 150 kg - Stack height 1.8 m up to max. 2.0 m - Maximum lifting height: 2.1 m - Travel speed: - Horizontal approx. 120 m/min - Vertical approx. 45 m/min - Manipulator suitable for slightly air-permeable, smooth materials such as coated chipboard, blockboard, raw MDF, raw HDF, raw chipboard (good quality) - Upgrade: Vacuum capacity for suction units on the manipulator 100 m³/h for a material mix in the warehouse such as MDF and raw chipboard - Connected load 6 kW - Portal bridge with vibration dampening, manipulator head with lifting device as well as gripper arm made of steel, space-saving due to low design height Articulated arm design with direct drive via steel band thus wear-free and vibration-resistant - Electronic panel position measurement - Panel rotation correction: The panels are measured with sensors and stacked accurately - Separation system for thin panels via integrated weight measurement - Inbound and outbound storage position - Direct loading onto the machine - Warehouse management software Previous list price: €110,000.00 Availability: short-term Stock location: Flörsheim

Condition: ready for operation (used), IM Very good condition. Dlodpfxsvunm Ae Addoa

Condition: used, Holz Her STREAMER 1057 FÜ + PU Edge thickness 0.4 - 6 mm Modern control with selector switch for adjusting the units Pre-milling unit for attaching before the gluing part Fully automatic edge magazine for rolls and strips Glue application station GLU-JET cartridges + PU gluing Glue application using nozzle technology Workpiece height 6-60 mm Automatic glue height adjustment High-quality 3-roller printing unit, 1st roller motorized Cutting unit pneumatic. for rolls and strips up to 6 mm edge thickness with pneumatic adjustment of 0-10° angle of the miter saws milling unit, flush milling 6 mm, radius milling - chamfer milling - 15° Dljdpexqa Iyjfx Addsa corner copying unit - 3 mm edge thickness scraping unit for chamfers and radii with 2 scraping blade holders surface scraping unit - finish spraying device - PU machine with all processing tools machine is WORKSHOP TESTED in TOP CONDITION

Condition: good (used), Year of construction: 2009, I sell the 3-axis CNC working centre HOLZ-HER PRO-MASTER 7023 with beam table Year 2009. Configuration: 3-axis main spindle 6 KW Tool magazine 8 positions HSK63 1 grooving saw X-direction Dlsdjtt S D Rjpfx Addja Drilling head 16+4+2 spindles Useful working area 3200 x 1060 x 378mm. 2 working fields, 4 clamping areas Automatic central system of lubrication. Holzher software controller with full instructions. Pump BECKER 250 m3/hr. Good condition. Available immediately.

Condition: excellent (used), 5-Axis Machining Center HOLZ-HER ProMaster 7125 -used- Console machine, pneumatic workpiece stops with double-acting cylinders, pneumatic loading aids, hardened, dust-protected prism guides, helical rack and pinion drive (X-axis), ball screw drives on Y and Z axes, network card for remote maintenance, electrical cabinet cooling with heat exchanger, manual control device, C-axis, A-axis, saw unit for grooving in the X direction, revolving disc tool changer, including safety fence, including tread mats, pendulum operation possible, laser for suction cup positioning, automatic central lubrication, uninterruptible power supply ----- Technical Data ----- Dledpfx Adexlqkhedsa Processing length (routing R) X: 3,385L / 3,605L mm, Processing length (routing R) Y: 1,335 mm, min. workpiece thickness: 215 mm, control software: CAMPUS HOPS 7, main spindle motor power: 12 kW (S6), main spindle speed: 1,000 - 24,000 rpm, main spindle interface: HSK-F63, spindle cooling: liquid cooling, drilling unit motor power: 3 kW, drill spindle interface: M10, locating fit 11mm, number of vertical drill spindles: 10 pcs, number of horizontal double drill spindles in X direction: 2 pcs, number of horizontal double drill spindles in Y direction: 1 pc, saw blade diameter of saw unit: 125 x 20 mm, number of consoles: 6 pcs, number of tool changer positions: 18 pcs, vacuum pump capacity: 140 m³/h, extraction port diameter: 250 mm, required volume flow: 6,100 m³/h, required static pressure: 1,300 Pa, required air velocity: 35 m/s, compressed air connection: 6-8 bar, compressed air consumption: 300 Nl/min, weight: 4,600 kg, year of manufacture: 2019 Quality Information: - complete basic cleaning - electrics checked - pneumatics checked - set as per manufacturer's specifications - immediately ready for operation

Condition: new, Year of construction: 2024, functionality: fully functional, feed rate X-axis: 9 m/min, workpiece height (max.): 50 mm, edge thickness (max.): 5 mm, warranty duration: 12 months, HOLZ-HER Edgebander ARTEA 1020 Stock machine – Subject to prior sale Year of manufacture: 2024 - Base machine 1020 Dlodexpgv Ujpfx Addoa - Edge Control BC15 with Vi.Se. (Visual Setting) - LED machine lighting - Jointing milling unit - GluJet for PUR / EVA including adhesive reservoir - Milling - Profile scraper - Surface scraper - Buffing unit

Condition: used, Year of construction: 2003, Used machine Year of manufacture: 2003 Features and technical data: - Control system with LCD display - Swiveling operator panel - Program memory - Manual pressure bridge adjustment - Feed via transport chain - Extendable workpiece support Jointing unit 1961: - 2 x 2.0 kW - Diamond jointing cutters for up-cut and down-cut operation Edge magazine 1903: - Support plate 820 mm, max. loading capacity 40 mm - Automatic feeding of coil and strip material Adhesive application system 1906: - Cartridge system with sensor-controlled nozzle - Automatic reloading - Use of PUR adhesives possible Pressure unit 1816: - With powered roller - Pneumatic control of the pressure unit End trimming unit 1918: - 2 x 0.22 kW - Swivels from 0 to 10°, pneumatically adjustable Milling unit 1942 MOT 2: - For flush, radius, and chamfer milling - Motorized adjustment - Air nozzle at milling unit Corner copying unit 1832: - Corner copying up to r = 3 mm, postforming up to r = 6 mm Radius scraper unit 1929 MOT 2: - For plastic edging up to 3 mm - Chip collection box for radius scraper Surface scraper 1964: - Process-controlled surface scraper - Air nozzle at surface scraper Buffing unit 1940 Edge thickness, coil material: 3 mm Edge thickness, strip material: 5 mm Max. edge thickness, corner copying: 3 mm Workpiece thickness: 6-45 mm Workpiece thickness, corner copying: 45 mm Dledpfx Adewka Nyedja Min. workpiece length: 180 mm Feed speed: 8 m/min Distance, workpiece support: 470 mm Support plate diameter for edge material: 800 mm End trimming blade for coil material up to: 3 mm Heating up time: 3.5 min Jointing cutter power: 2 x 2 kW End saw power: 2 x 0.22 kW Milling station power: 2 x 0.6 kW Corner copying power: 0.22 kW Extraction nozzle jointing unit: 120 mm Extraction nozzle milling unit: 70 mm Extraction nozzle scraper unit: 70 mm Dimensions: 5,350 x 1,669 x 1,940 mm Weight: 1,200 kg Location: Röllbach Availability: short notice

Year of construction: 1989, condition: good (used), - tilting spindle under the account Dedpfx Aogxpilsddela - shaft diameter 50mm - up and down adjustment - pneumatic adjustment of the spindle position - 400V power supply - THE FEED IS NOT THE SUBJECT OF THE OFFER

Condition: used, functionality: fully functional, Edge thickness 0.4 – 3 mm SPS screen control Fully automatic edge magazine Fully automatic roll magazine – cross-cut shears Cartridge + PU gluing station + automatic dosing nozzle Workpiece height 6 – 45 mm End trimming unit swivels at 0 and 10 degrees Flush, bevel, and radius milling, swivels up to 15 degrees Profile scraper Buffing unit Soundproof cabin CE version Machine is FUNCTION-TESTED and in GOOD CONDITION Djdpfx Aew Igg Soddsla ex works

Condition: good (used), Year of construction: 2000, I sell the 3-axis CNC working centre HOLZ-HER ECO-MASTER 7113 with beam table Year 2000. Configuration: 3-axis main spindle 7,5 KW Tool magazine 4 positions HSK63 1 grooving saw X-direction Drilling head 9+2 spindles Dlsdpfjtt Sy Hjx Addoa Useful working area 2300 x 1000 x 130mm. 2 working fields, 4 clamping areas Automatic central system of lubrication. Holzher software controller with full instructions. Pump RIETSCHLE 2,2 KW Good condition. Available immediately.

Condition: excellent (used), Machining Centre HOLZ-HER Evolution 7405 - used - Through-feed processing, 4-sided edge trimming possible, automatic suction cup positioning, hardened, dust-protected prism guides, ball screw drives on all axes, network card for remote maintenance, integrated control cabinet, control cabinet cooling with heat exchanger, manual control device, saw unit for grooving in the X direction, pick-up tool changer ----- Technical Data ----- Minimum workpiece length X: 200 mm Minimum workpiece width Y: 70 mm Minimum workpiece thickness: 8 mm Maximum workpiece length X: 3,200 mm Maximum workpiece width Y: 920 mm Maximum workpiece thickness: 70 mm Machine control software: CAMPUS HOPS Main spindle motor power: 6.5 kW Main spindle speed: 1,000 - 18,000 rpm Dlsdpexddhksfx Addsa Main spindle mount: HSK-F63 Drilling unit motor power: 1.7 kW Drill spindle mountings: M10, precisely fitted 11 mm Number of vertical drill spindles: 9 pcs Number of horizontal double drill spindles in X direction: 2 pcs Number of horizontal double drill spindles in Y direction: 1 pc Saw blade diameter of saw unit: 120 x 20 mm Number of tools in changer: 6 pcs Extraction connection diameter: 2 x 120 mm + 1 x 140 mm Required air volume flow: 4,100 m³/h Required static negative pressure: 2,500 - 3,000 Pa Required air velocity: 30 m/s Compressed air connection: 6 bar Compressed air requirement: 300 NL/min Dimensions (LxWxH): 3,673 x 1,924 x 2,340 mm Quality info: - Completely basic cleaned - Electrical system checked - Pneumatics checked - Adjusted according to manufacturer specifications - Immediately ready for operation

Condition: excellent (used), Year of construction: 2020, 158.000 running metres BASE MACHINE AURIGA 1308XL TECHNICAL DATA Edge banding machine for edgebanding and finishing of sheet materials Edge thickness of roll material: 0.4-3mm (depending on material) Edge thickness of strip material: 0.4-8mm (depending on material) Edge cross-section: max. 6x42mm Edge height: max. 65mm Workpiece thickness: 8-60mm (restrictions possible for individual units) Workpiece width: min.65mm Workpiece length: min.160mm (without corner copying 1832) Workpiece length: min.180mm Feed speed: 10m/min. MACHINE OPERATION Edge Control 19 with 18.5" touchscreen colour monitor 16:9 Powerful control system with extremely simple operation for efficient machine set-up and changeover. Rotating and swivelling control panel at eye level Motorised pressure bridge adjustment iTronic - Adaptive pressure and adhesive quantity control Automatic, programme-dependent fine adjustment Optimum adaptation to edge thickness, edge materials and adhesive types guarantees the best processing results Automation package consisting of - Automatic glue quantity control - adaptive snipping knife Dljdpfxoxayvpe Addea - adaptive printing unit incl. residual adhesive quantity display incl. fully automatic PUR flushing routine Premilling unit FG201 with 2 milling heads for joining the panel edge 1x counter-rotating, 1xsynchronised, Milling cutter, diamond Ø70x64x30 mm,Z2+2 Edge feeder 1903 automatic transport of rolls and strips max. loading capacity: 40 mm Glu Jet GJ301 glue application system (2,3kW,50Hz) Automatic glue height adjustment Glu Jet hybrid technology for EVA and PUR adhesives Adhesives in cartridge and granulate form for neutral and coloured adhesives Hopper for 1.4 kg cartridges (4 cartridges) Hopper for 1.5 kg granulate Pneumatic pressure unit 1912-3 First roller driven with pneumatic immersion control, 2 conical holding pressure rollers Cutting unit 1918 (60 mm) pneumatic (2 x 0.45 kW, 12000 min-1) pneumatic swivelling 0/10° Dust extraction hoods for end trimming unit 1918 Multifunctional trimming unit 1827 MOT4 for trimming the top and bottom longitudinal edge with motorised positioning of the horizontal tracing shoes with motorised positioning of the trimming motors in axial direction incl. pneumatic adjustment (top and bottom separately) for flush-radius routing incl. blow nozzles - Flush cutting unit - Radius - Tilt the chamfer 0 - 15°, manually (with max. edge thickness 6 mm) Pneumatic swivelling device for trimming unit 1827 MOT4 Pneumatic swivelling to bevel 15° from the control unit Pneumatic vertical tracer rollers Adjustment of the vertical tracer roller by 0.1 mm for routing with edge overhang Corner rounding unit (1x0,35kW,200Hz,12000min-1) Corner copying function up to 3 mm edge thickness Workpiece thickness: 12 - 60 mm, with DIA tool R=2mm Scraper unit 1929 MOT4 incl. high-gloss package with motorised adjustment of the horizontal feeler rollers, incl. pneumatic adjustment (separate top and bottom) Surface scraper FK701 With pre- and post-scraping for removing the adhesive residue along the complete panel length for a clean glue joint. Buffing unit 1940 (2 x 0,09 kW, 50 / 60 Hz, 1400 min-1) For finishing and polishing edges, with 2 textile discs, swivelling 0 - 5°

Condition: used, Year of construction: 2005, Used machine Year of manufacture: 2005 Equipment and technical data: Travel paths: - X-axis: 2,685 mm - Y-axis: 1,095 mm - Z-axis: 140 mm Milling unit: - 6 kW, water-cooled - Tool holder: HSK 63 F - Speed: 1,000 - 18,000 rpm Tool changer: 6-position, side-mounted Drilling head: - 9 vertical drilling spindles, 32 mm pitch - Horizontal spindle: 1+1 - Vertical spindle: 1+1 Grooving saw in X direction Dlsdpfx Aswka H Eeddja Control: Twin CAM 32 Vacuum pump: 100 m³/h Includes vacuum suction cups Dimensions: 5,200 x 2,843 x 1,855 mm Weight: approx. 3,500 kg Availability: by arrangement Storage location: Röllbach

Condition: good (used), Year of construction: 2004, I sell the 3-axis CNC working centre HOLZ-HER UNI-MASTER 7226 with beam table Year 2004. Dljdpfx Adji U Dxusdoa Configuration: 3-axis main spindle recently full reconditioned / Water cooled Tool magazine 6 positions HSK63 on working head 1 grooving saw X-direction Drilling head 16+4 spindles Useful working area 3100x1360mm. 2 working fields, 4 clamping areas Automatic central system of lubrication. Holzher software controller with full instructions. 2x Pump SIEMENS ELMO-L S22 2,35KW. Good condition. Available immediately.

Condition: used, Year of construction: 2008, Used machine Year of manufacture: 2008 Dledev Sv Enspfx Addoa Edge Control control system with 18.5" touchscreen color monitor 16:9 Swiveling operator panel, Program storage, Motorized pressure bar adjustment, Feed via transport chain, Feed speed: 8-18 m/min Extendable workpiece support, Infeed fence with motorized adjustment Jointing unit 1961, Diamond jointing cutter for climb and counter rotation, Automatic adjustment to workpiece height Edge feed 1903 Pre-trimming up to 3 x 45 mm (depending on material) Glue application system 1905 Multi-System Automatic glue height adjustment with sensor nozzle, Pressure regulator for adjusting the cartridge contact pressure, Use of PUR adhesives possible, Pressure unit 1913 MOT, First roller driven End trimming unit 1918 with pneumatic adjustment End trim saw pneumatically swiveling, Multifunction unit 1824 MOT 4 with multifunction cutter radii 1,2,3 mm Corner copying unit 1832 Corner copying up to 3 mm edge thickness Radius scraper 1929 MOT 2 With motorized adjustment of horizontal tracing rollers With pneumatic adjustment (top and bottom separate) Chip collection box for radius scraper, Surfacing scraper 1964 For removing glue residue for a clean glue line With extraction hoods Spray unit 1856 for infeed and outfeed area Buffing unit 1940 For finishing and edge polishing ----- Technical Data ----- Edge thickness roll material: 3 mm, Edge thickness strip material: 8 mm, Max edge thickness for corner copying: 3 mm, Workpiece thickness: 45 mm, Workpiece thickness for corner copying: 45 mm, Min. workpiece length: 180 mm, Feed speed: 8-18 m/min, Distance workpiece support: 470 mm, Support table diameter for edge material: 800 mm, End cut knife for coiled material up to: 3 mm, Heating time: 3.5 min, Jointing unit power: 2 x 2 kW, End trim saw power: 2 x 0.22 kW, Milling station power: 2 x 0.35 kW, Corner copying power: 0.22 kW, Extraction port jointing unit: 120 mm, Extraction port milling unit: 70 mm, Extraction port scraper unit: 70 mm, Total length: 5,350 mm, Dimensions (LxWxH): 5,350 x 1,669 x 1,940 mm Picture of operating hours taken from a recording in 2022 Availability: short term Location: Röllbach

Condition: used, Year of construction: 2015, Used machine Djdpfx Ajxllvrjddsla Year of manufacture: 2015 Equipment and technical data: - Base machine with manual pressure bridge adjustment - Extendable workpiece support - Joint milling unit FG 201 with 2 milling heads - Edge feeding with single infeed, automatic transport of roll and strip material - Glue application system Glu Jet GJ 301, automatic glue height adjustment (sensing nozzle) - Pressing unit 1912-3 pneumatic - Pneumatic trimming unit 1918 (60 mm) - Extraction hoods for trimming unit - Multifunction milling unit FR 201 - Corner copying unit 1832 for up to 3 mm edge thickness - Scraper unit 1929 - Chip collection box - Flat scraper 1964 - Buffing unit 1940 - Complete spray device 1856 Minimum workpiece length: 160 mm Workpiece thickness: 60 mm Edge thickness: 0.4-6 mm Feed rate: 10 m / min Overall length: 4630 mm Weight: 1250 kg The extraction bridge shown in the pictures is not included in the scope of delivery! Location: Hesse Availability: approx. December 2025

Condition: used, Year of construction: 1989, Used machine Year of manufacture: 1989 Dlsdsw I U E Ajpfx Addea Condition: Function tested Equipment and technical data: Max. edge thickness: 20 mm Max. edge height: 51 mm Max. thickness of coil material: 3 mm Min. workpiece length: 140 mm Min. workpiece width: 60 mm Glue system: 1906 cartridge Pressure unit Milling unit 1920 for flush milling up to 20 mm and chamfer milling Required space (LxWxH): 3150x1800x1375 mm Weight approx.: 800 kg Location: Flörsheim Availability: Short-term

Condition: used, Year of construction: 2022, Used machine Year of manufacture: 2022 Condition: as new Includes 6 months full warranty! Only 70 operating hours; the machine has not yet been used in production! Equipment and technical data: BASE MACHINE Holz-Her Processing Center DYNESTIC 7535 10.5 Lift Processing length: 3100 mm Machine frame: welded construction with ground and hardened prism guides for the gantry, aggregate head, and consoles. Gantry design. Rack-and-pinion drive, helical gears in X and Y direction, 1 precision ball screw in Z direction for accurate positioning. MATRIX TABLE Fixed, continuous processing table with grid markings and through-slots in X and Y direction, slot spacing 50 mm. Includes 25 meters of sealing cord for fixing the sacrificial plate. 1 work zone with stop rails/stops - stop height 30 mm, pneumatically retractable. 2 stop rails in Y direction and 1 stop in X direction right (as seen from the front of machine). Remote maintenance capability Integrated network card for transfer of control and program data. Data transmission via high-speed internet connection. Requirement: High-speed internet connection at the machine. USB port For data backup and for directly importing processing programs at the control panel. TECHNICAL DATA Working dimensions 7535 10.5: Max. nesting table surface: X = 3100 mm, Y = 1560 mm Max. travel paths: X = 4695 mm, Y = 2305 mm, Z = 565 mm Max. machining height 7535/7735 Classic without pusher: Z = 300 mm from table top (excluding sacrificial plate) Max. pusher clearance height above table for Push/Auto/Lift versions: Z = 250 mm from table top (excluding sacrificial plate) Dlodpfswxz Uysx Addja Maximum programmable speed Vector speed: 128.0 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min MACHINE OPERATION SOFTWARE CAMPUS V7 PLUS CAD/CAM software, 1 license incl. material removal simulation BetterSim 1 software license secured via dongle for the machine CAMPUS V7 PLUS software for CNC processing centers: Consisting of: 1. CAMPUS NC-HOPS 2. CAMPUS aCADemy 3. CAMPUS MT-Manager 4. CAMPUS Workcenter V7 PLUS 5. CAMPUS 3D material removal simulation BetterSim CAMPUS NC-HOPS Graphical variant system with conversational programming and CAD/CAM features for creating part variants using macro technology. Hi-Speed USB-Device Network Server Allows use of the CAMPUS single license on the machine or a PC in the same network. Only one license may be used in the network at a time! Additionally: CAMPUS V7 PLUS CAD/CAM software, 1 license incl. material removal simulation BetterSim 1 software license secured via dongle for office or machine CAMPUS V7 PLUS software for CNC processing centers: Consisting of: 1. CAMPUS NC-HOPS 2. CAMPUS aCADemy 3. CAMPUS MT-Manager 4. CAMPUS Workcenter V7 PLUS 5. CAMPUS 3D material removal simulation BetterSim CAMPUS NC-HOPS Graphical variant system with conversational

Condition: new, Year of construction: 2025, Showroom machine Year of manufacture: 2025 Features and technical specifications: - Base machine DYNESTIC 7507 10.57 push - Upgrade from BetterNest rectangular nesting to: CAMPUS BetterNest freeform nesting software - Uninterruptible Power Supply - UPS (ZB27) - Touchtool tool length measurement - 10.3 kW router spindle - Drilling unit with 14 spindles - 1 additional machining field (Field A) at the rear with 1 stop, height 70 mm, pneumatically retractable Dlsdpfx Aexc Rmkoddja - 2 electronically monitored side stops at the front, Field A + D, in X-direction for the front stop row (BF8) - 10-position tool changer 7873 - Tool changer 7872, one-position aggregate magazine, pivotable in X and Y direction for Clamex aggregate - 2 x 140 m³/h and 1 x 250 m³/h dry-running vacuum pumps, 400 V - 16-circuit vacuum system (VF16) - software controlled, incl. additional 25 meters sealing cord - Laser pointer - red (one laser pointer) Field D (ZB8) for positioning of vacuum suction cups or tracing the workpiece contour - Automatic central lubrication - Vacuum suction cups for smooth table surfaces, complete, 140x115 mm, height 30 mm with connecting hose - Thin sheet ejector as an addition to the ejector for special materials below 4 mm material thickness and standard wood-based materials under 2 mm - Complete conveyor belt, pusher conveyor belt, pusher table - TouchLabel PRO - touchscreen and label printer mounted on stand - Production control computer NEXTEC 4.0 - Extraction funnel at the end of the pusher conveyor belt - Availability: by arrangement - Location: Flörsheim

Condition: used, Used machine Equipment and technical specifications: Automatic edge feeder Cartridge glue system 4-roll printing unit Cross-cut saw unit Flush trimming unit Combination trimming unit: flush/bevel/radius Dsdpfx Adjw Nad Hedola Radius scraper Buffing unit Edge band thickness 0.3 - 20 mm (depending on unit) Edge band height max. 66 mm Edge band length min. 200 mm Feed rate 8/16 or 12/24 m/min With LIGMATECH workpiece return system The return line of this return system is located above the panel processing level. The workpieces move back to the operator on an inclined plane. Special features compared to the ZHR 0x models: Automatic detection and rotation of parts from transverse to longitudinal Automatic adjustment of the rotation speed to the workpiece length Minimum and maximum workpiece dimensions For longitudinal edge processing: 2200 x 1000 For transverse processing with subsequent rotation: 250 x 120/2200 x 800 Maximum workpiece thickness: 60 mm Location: Bavaria Availability: Short-term

Condition: new, Year of construction: 2024, New machine Year of manufacture: 2024 Specifications and technical data: Base machine 1057 XL C with Beckhoff touch-screen control Extendable workpiece support 600 mm Extension for extendable outrigger Standard infeed fence 3 LED lights in the infeed area Jointing unit with two motors Dodpfxjw I U Rfj Addsla DIA jointing cutter 70 x 64 x 30 mm Z2+2, left and right rotation Edge feeding system 1903, fully automatic GluJet 301 adhesive application system Automatic reloading function Magazine for 1.4 kg adhesive cartridges (holds 4 cartridges) GluJet collection container Pressure unit 1912-3, pneumatic Spray device GM 201 after pressure unit End trimming unit 1918, pneumatic Extraction hoods for end trimming unit Combined trimming unit FR201 with DIA cutters R=2 mm Contour trimming unit 1832 Shelf program Radius scraper ZK 301 Chip collection box Flat scraper FK 701 Spray device front and rear TR201 Buffing unit 1940 Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2020, Used machine Year of construction: 2020 Equipment and technical data: Extendable workpiece support, spacing 600 mm Jointing milling unit FG201 with 2 milling heads for edge jointing on panels Cutter, diamond 70 x 64 x 30 mm, Z2 + 2, left-hand rotation, Air Stream System (HOLZ-HER / LEUCO Patent) Dlodpsw Nafdofx Addsa Cutter, diamond 70 x 64 x 30 mm, Z2 + 2, right-hand rotation, Air Stream System (HOLZ-HER / LEUCO Patent) Edge feeding 1903 automatic transport for rolled and strip material GJ301 adhesive application system with sensing nozzle Automatic refill function, level monitoring with automatic glue refill Pressure unit 1912-3 pneumatic, first roller is driven with pneumatic immersion control End trimming unit 1918 (60 mm), pneumatic, chamfering 0/10 degrees, pneumatic adjustment Extraction hoods for end trimming unit 1918 Multifunctional milling unit FR201 (2 x 0.6 kW, 18000 min-1) for flush, radius, and radiused exit Corner copying unit 1832 (1 x 0.35 kW, 200 Hz, 12000 min-1), corner copying function up to 3 mm edge thickness Cutter, diamond Ø 53 mm x 10 mm x 16 mm, Z = 3, R = 2 mm, with CM technology (LEUCO system) with integrated chip removal, for the contour milling unit 1832 Scraper unit 1929 Chip container HW reversible knives for scraper holder R = 2.0 mm (2 pcs required) FK701 FL-SCRAPER HM Location: Solingen Availability: Short-term

Condition: used, Year of construction: 2014, Used machine Year of manufacture: 2014 Features and technical data: - Extendable workpiece support - Joint milling unit FG201 with 2 milling heads incl. DIA cutters - Fully automatic edge feed 1903 - Glue application system cartridge GlueJet 301 with automatic glue height adjustment (sensor-controlled nozzle) - Special accessory: pressure regulation of cartridge contact pressure - Pressure section 1912-3 pneumatic, first roller driven with pneumatic plunge control - End trimming unit 1918, pneumatic adjustment - Milling unit FR 201 multifunctional milling unit for flush, radius, and radius run-out incl. DIA cutters - Corner copying unit 1832 up to 3 mm edge thickness incl. DIA cutter - Scraper unit 1929 with 2 scraper holders - Chip collection box - Surface scraper 1964 Minimum workpiece length (mm): 160 Workpiece thickness (mm): 6 - 45 Edge thickness (mm): 0.4 - 3 Feed speed (m/min): 10 Total length (mm): 4630 Weight (kg): 1250 Dljdpjxavr Hjfx Addea Availability: short notice Location: Flörsheim

Year of construction: 2025, condition: new, Exhibition machine Year of manufacture: 2025 Dodpfx Aoxavtwsddsla Location: Flörsheim Availability: by arrangement

Condition: used, Year of construction: 2012, Used Machine Year of Manufacture: 2012 Base Machine - Dynestic 7521 20.6 Dynestic Table For classic nesting processing with wear plate Processing length 6250 mm (DYNESTIC 20.6 comes with additional 4th stop in Y already included) Machine frame in welded construction with ground and hardened prism guides for the gantry, unit head, and consoles Gantry-type design Rack and pinion drive, helical-toothed, in X and Y directions, Ball screw spindle in Z direction for precise positioning Technical Data: The technical data refers to the DYNESTIC 7521 - 20.6 Please refer to the respective datasheets. Processing Dimensions: Max. workpiece size for trimming: X = 6250 mm Y = 2100 mm Max. travel distances: X = 7360 mm Dsdpow I U Ecsfx Addola Y = 2720 mm Z = 325 mm Max. clearance height on DYNESTIC table: Z = 1st level 318 mm / 2nd level 418 mm from table surface (without tool, without holder) Maximum programmable speed: Vector speed: 128.0 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min 4-stage extraction hood with pneumatic height adjustment and observation window Voltage 400 V, 50/60 Hz CONTROL: Dual-core processor Operating system Windows XP 80 GB hard disk / 1 GB RAM RJ45 network port 10/100 Base-T Fast Ethernet US keyboard and Microsoft IntelliEye mouse (optical) CD-ROM / CD-RW drive (CD writer) Remote maintenance Integrated network card for transmission of control and program data. Data transfer via high-speed internet connection required. Requirement: High-speed internet connection at the machine. DYNESTIC Table Fixed, continuous processing table with grid layout, continuous grooves in X and Y direction, distance between grooves 50 mm with 25 meters of sealing cord for fixing the wear plate 1 processing field with stop rails / stop Height 30 mm, pneumatically retractable 2 stop rails each in Y-direction and 1 stop in X-direction right side (from machine front edge perspective) Vacuum Fields Single-circuit vacuum system Drilling Unit 7976, 24 spindles Motor power 3.0 kW 18 vertical spindles, individually selectable L-shaped arrangement: 10 in X and 8 in Y direction 32 mm grid Max. drill diameter: 35 mm Total drill length: 70 mm from mounting end (depending on board thickness) Spindle extension stroke: 70 mm Rotation: Alternating right/left n(max.) 1000 - 5710 rpm steplessly adjustable Mounting: M10 thread - 11 mm fitting Without tool, without holder 6 horizontal spindles 2 double drilling spindles in X-direction (Distance 32 mm between 1st and 2nd horizontal spindle) 1 double drilling spindle in Y-direction Mounting: M10 thread, 11 mm fitting Max. total drill length 70 mm from mounting end Without tool, without holder Free slot 1 for: Optional double drilling spindle in X-direction or Vertical adapter with double pressing force Free slot 2 for: Optional saw in X-direction or Vertical adapter with double pressing force Milling Unit 7831, 2-stage Power: 11.0 kW (S6) n(max.) = 1000 - 24000 rpm, steplessly adjustable, two-stage feed stroke max. power at 12000 rpm to 24000 rpm Air-cooled with HSK-F 63 tool holder with right-hand rot...