Used Indexable Inserts for sale (3,029)

Year of construction: 1999, condition: reconditioned (used), Machine is currently undergoing overhaul PROCESSABLE MATERIALS Depending on material properties and sheet configuration: · Paper with a minimum grammage of 80 gsm · Cardboard or solid board up to a grammage of 2,000 gsm · Corrugated board up to a total thickness of 4 mm (max. sheet curvature 4%) PERFORMANCE DATA Max. sheet format: 820 x 1,130 mm Min. sheet format: 350 x 400 mm Max. cutting force: (400 t) 4.0 MN Max. machine speed: 9,000 sheets/h Standard equipment of the machine: Feeder Non-stop high-performance sheet feeder W3 equipped with: • Automatic non-stop device • Automatic pallet changeover • Suction head • Double-sheet detector • Motorized stack side correction • Motorized suction head adjustment • Conveyor table with pneumatic cover frame • Compressed air and vacuum pump Register Table • Operator-side side lay, switchable between pull and push mode • Light sensor for accurate side alignment of sheets • Fine adjustment of the side lay • Two active front lays with light sensor for register control • Two inactive front lays for sheet stabilization • Separate fine adjustment of gripper edge for drive and operator side • LED display for accurate front and side lay registration • Trend display for sheet detection • Sheet rejection, disabling only the feeder • Height-adjustable top lay for positive sheet guidance Die-cutting station • Roller-guided support rails for the chase • Roller guide for die-cutting plate on swing-out support arms • Motorized die pressure adjustment • Automatic device for lifting the chase to the platen • Electronic die-cutting force display with max. pressure limitation • Vacuum device in sub-table for thin cutting plates Stripping Unit Bsdpfx Absyuuzdjtsdg • Frame drive and frame lift for upper tool frame • Mount for the stripping board with centerline fine adjustment • Device for sample sheet removal • Upper tool frame • Lower tool frame Delivery • Fully automatic pile stacker, pre-selectable • Counted sub-stacks with automatic insertion of uncut sheets • Can form sub-stacks (interleaved sheets between 250 gsm – 800 gsm) • Frame lift for upper tool frame • Mount for change frames with electric adjustment in running direction • Pneumatic frame locking • Switchable gripper opener cam and sheet ejector • Sheet jogging device • Integrated conveyor belt for gripper edge or waste grid removal (double-cut) • Separator sheet magazine with electronic level control, refillable from B-side during production • Tool frame with centerline • Change frame for standard pile delivery / gripper edge removal • Change frame for blank separation grid • Mounting kit for separation punch • 8 x sheet hold-downs for standard pile delivery • 4 x cross support bars Options: • QTM – Patented guide rails • QTM – Chase with quick lock system and X/Y adjustment • QTM – Upper stripping frame with quick lock system • QTM – Upper delivery frame with quick lock system • Control upgrade to latest Siemens S7 controller • New generation frequency converters • Modem for remote service connection • Machine height increase: 900 mm

Condition: used, Year of construction: 2023, operating hours: 3,300 h, functionality: fully functional, machine/vehicle number: L0098, table height: 1,000 mm, table width: 195 mm, total width: 1,500 mm, total length: 3,500 mm, total height: 2,150 mm, spindle speed (min.): 750 rpm, table length: 3,250 mm, spindle speed (max.): 6,000 rpm, number of spindles: 8, rotational speed (min.): 750 rpm, rotational speed (max.): 6,000 rpm, drill chuck size: 11 mm, workpiece weight (max.): 1,200 kg, operating pressure: 8 bar, air demand: 15 m³/h, KS Maschinenbau - KS LBM DB 04 DR For sale is a row drilling machine, also known as a strip drilling machine. The row drilling machine KS LBM DB 04 DR is designed for drilling strips and guide rails made of aluminum, plastic, and wood, as well as roller shutter end strips (for wood profiles up to 3 meters long and up to 90 mm in height). The machine is equipped with 4 pairs of three-phase drilling units. Four holes each can be drilled simultaneously or with a time delay from above and below. The spacing between the drilling units is manually adjusted using an indexing system for various distances. The index holes are fitted with drill bushings into which the hardened index pins are centered. Bdsdpfoywtxbex Abteg The offered strip drilling machine comes with 8 drill heads (4 oriented downwards, 4 upwards). We have used this machine in our workshop to drill wooden fence profiles. It has provided us with reliable service over the past few years. As our customer is switching to plastic profiles, we no longer have use for it. This machine configuration includes 8 extraction adapters for chip extraction, along with hoses and a manifold for customer-side extraction. Further videos and technical data about this machine series can be found at the following link: ksschulten.com/en/products/drilling-machines/strip-drilling-mach ine-ks-lbm/video.html The machine's operating manual is of course still available.

Condition: like new (used), amount 1 Set For sale is a package of KERN cutting inserts. Some are new and some are slightly used. Year of manufacture unknown. 50 pcs. -> F3 3947 0029904 HP25A Bsdpfxjyr Si Te Abtodg 30 pcs. -> F3 3943 pcs. -> F3 3943 pcs. -> KERN KG – Diverse

Condition: used, mileage: 1,15,650 km, power: 90 kW (122.37 HP), first registration: 05/2023, fuel type: diesel, color: red, gearing type: automatic, emission class: euro6, number of seats: 5, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), immobilizer system, navigation system, second-hand vehicle warranty, soot filter, Special Equipment: Audio navigation system Discover Pro Streaming & Internet (touchscreen, Bluetooth, USB), Business Package Premium with navigation, luggage securing net, Mobile Online Services We Connect Plus, tire repair kit (Tire Mobility Set), special paint finish in Tornado Red (solid), reversible luggage compartment mat, additional winter tires (customer specification required). Further Equipment: 3-point seat belt rear center, driver/front passenger airbag, front passenger airbag deactivatable, antenna diversity, traction control (ASR), Comfortline / Life / Business equipment, automatic headlight control (ALS) with Leaving Home / Coming Home function, left and right aspherical exterior mirrors, electrically adjustable and heated exterior mirrors, painted exterior mirrors, left exterior mirror with automatic dimming, outside temperature display, integrated indicator in exterior mirror, brake assist, Chrome Package (1), chrome trim strips on side windows, headliner fabric in grey, roof rails, dual-tone horn, front and rear parking assist, LED entry lights in doors, electronic differential lock (EDS), electronic stability program (ESP) with electromechanical brake booster, driver assistance system: trailer stabilization program, driver assistance system: automatic distance control (ACC incl. stop & go function), driver assistance system: hill start assist, driver assistance system: pedestrian detection, driver assistance system: multi-collision brake, driver assistance system: fatigue detection, driver assistance system: lane keeping assist (Lane Assist), driver assistance system: ambient monitoring system (Front Assist) with City Emergency Braking function, electric windows front and rear, remote tailgate unlocking, tinted laminated windshield, textile floor mats, LED footwell lighting in front, adjustable luggage/load compartment floor, luggage compartment partition (cargo net), luggage compartment cover/roller blind, luggage compartment lighting, front cup holders with cover, glove compartment with cooling function, LED rear lights, rear window wiper, interior trim: Cross Hatch decorative inserts, interior trim: Piano Black/gloss black centre console inserts, interior mirror with automatic dimming, proactive occupant protection system, Isofix child seat anchorages for rear seats (incl. i-Size child seats), 5-door body, LED license plate lighting, Keyless Start, child safety lock in passenger compartment, front and rear head airbag system including front side airbags, rear headrests (3), loading sill protection (plastic), lumbar support and backrest tilt adjustment, front left electrically adjustable, leather multifunction steering wheel with shift function, manually adjustable steering column (steering wheel), height and reach adjustable, front and rear LED reading lights, alloy wheels, rear center armrest, height and length adjustable front center armrest, Mobile Online Services preparation for We Connect and We Connect Plus, Mobile Online Services We Connect, model update, engine 2.0L - 90 kW TDI, Premium multifunction display (color), LED fog lights with integrated cornering light, rear fog light, non-smoker package, emergency call system, electric parking brake with auto-hold function, digital radio reception (DAB+), tire pressure monitoring system, split rear seat backrest with center armrest and through-loading facility, remote folding rear seat backs, low emissions to Euro 6d emissions standard, leather gearshift/selecto Bdjdpfx Abjytlb Eoteg

Condition: used, Year of construction: 1998, Overview This Krones - Linapac F-T-1800 automatic bottle packer was manufactured in 1998 and was previously installed in a returnable glass bottling line. The machine is designed for the automatic packing of filled bottles into beverage crates and is typically positioned downstream of the filler and inspection systems. The LINAPAC packer series is widely used in high-capacity beverage production lines due to its robust design and reliable crate handling. The system supports a wide range of bottle formats and crate types commonly used in the beer and beverage industry. The machine was originally operated in a high-performance production environment and is suitable for integration into returnable glass bottling systems with similar capacity ranges. Technical Data Manufacturer: Krones Model: Linapac F-T-1800 Machine type: Automatic bottle packer Year of manufacture: 1998 Bdedpfx Abjytq Taeteg Application: Automatic insertion of filled bottles into beverage crates Bottle Formats: - 0.25 L Individual bottle – Ø 57.5 × 215 mm - 0.33 L Ale bottle – Ø 61 × 236.5 / 238 mm - 0.33 L Ale bottle – Ø 68.5 × 234.5 mm - 0.5 L Ale bottle – Ø 68.5 × 270 mm - 0.5 L Steinie bottle – Ø 70.5 × 174 mm - 0.5 L Bavaria bottle – Ø 70 × 260 mm - 0.5 L NRW bottle – Ø 67 × 260 mm - 0.5 L Individual bottle – Ø 82 × 295 mm - 0.7 L GDB bottle – Ø 79 × 290 mm - 0.75 L GDB bottle – Ø 79 × 290 mm - 1.0 L GDB bottle (light) – Ø 84 × 305 mm - 1.0 L AMG bottle – Ø 83.7 × 298 mm Crate Formats: - 5 × 4 – 400 × 300 × 300 mm - 6 × 4 – 400 × 300 × 270 mm - 5 × 4 – 400 × 300 × 210 mm - 4 × 3 – 355 × 275 × 345 mm - 4 × 3 – 400 × 300 × 330 mm - 5 × 4 – 355 × 275 × 255 mm - 5 × 4 – 400 × 300 × 290 mm Condition: Used Availability: On request

Condition: good (used), Year of construction: 2007, functionality: fully functional, operating hours: 94,201 h, bending force (max.): 400 t, installation height: 595 mm, control type: CNC control, Bending length [mm] 3550 Pressing force [tons] 400 Control system Cybelec ModEva 10s Standard equipment: - Sturdy machine frame as a welded construction in all-steel design - Press beam with high bending strength - Electro-hydraulic upper drive via proportional valves - Modern block hydraulics - CNC rear stop for X and R axes, safe displacement of the stop fingers from the front by means of a safety interlock - Upper tool clamping system "EHT", manual, head width 26mm, load max. 3000 kN/m - Lower tool clamping system EHT, manual, clamping width 90mm for block tools and 13mm for single V-dies, without clamping - Control system: CYBELEC ModEva 10S on Windows, 2D graphic control with a 10.4" color screen - Control cabinet air conditioning Bdjdpfxjy Sauro Abtjg + Rear stop - System 1, 5 axes, straight finger, 140mm wide, adjustment of R axis 150mm + EHT quick clamping device, for upper tools, pneumatic, head width 26mm, load max. 3000 kN/m (self-centering horizontally) + EHT lower tool clamping, pneumatic, clamping width 55mm + Hardened insert strip, for EHT lower tool clamping 55mm / 90mm + Lower tool displacement, CNC-controlled, infinitely adjustable via rear stop 1 (max. 4550 mm working length) + Crowning device CNC-controlled, in the table without tool clamping, load max. 3000 kN/m + Safety device LaserSafe (up to max. upper tool height 440mm) + Additional foot switch + Bending aid 1st arm, load max. 1500N with 2 integrated support strips in standard design + Bending aid 2nd arm, load max. 1500N with 2 integrated support strips in standard design + 2 pcs. support strips for a bending aid with T-slot 14mm and scale and ball rollers + 2 pcs. table extension for bending aid + Short park position left + Short park position right

Condition: new, Year of construction: 2024, operating hours: 300 h, functionality: fully functional, type of input current: three-phase, The MK Diana Smartpacker packs your folding cartons fully automatically into shipping cases in one to four rows downstream of the folder gluer's compression and delivery station. An operator can also feed new shipping cases at a central control station and put sheets into the empty shipping case or insert intermediate sheets. Thus, up to three additional layers can be added semi-automatically. Bodpfjzbqwhox Abtjdg The MK Diana Smartpacker can pack up to 130,000 cartons per hour in shipping cases. It is operated via a touchscreen display. The settings are calculated automatically after entering the production parameters. In addition to placing the folding cartons onto the closure flap in the shipping case, the right and left turning stations allow the cartons to be placed onto crease lines 2 or 4.

Condition: used, power: 120 kW (163.15 HP), first registration: 08/2012, fuel type: diesel, color: orange, empty load weight: 5,990 kg, driver cabin: other, gearing type: other, Year of construction: 2012, operating hours: 4,850 h, number of seats: 2, * Compact sweeper CLEANGO, standard configuration for Germany, 50 km/h * Speed 50 km/h * Disc brakes on the front axle with dual brake calipers * Proportional parking brake * Load-dependent valve on the rear axle (required for all 50 km/h machines) * Driver's seat with air suspension * Seat belts * Radio with USB and SD card connection * Heated exterior mirrors * Additional work mirror * Colored rear view monitoring system with TFT monitor * Air conditioning * Tachograph * Cup holder * Independent control of the rotary brush (raise/lower, ground pressure, inclination) * Third front brush Cleango 500 * Weed brush for the 3rd brush * Additional work light (for the 3rd brush) * Suction nozzle with rubber insert * Suction pipe with rubber insert * Preparation for subsequent installation of the hand suction hose * Water return system Cleango 500 * Container door with high and low-level water drain valves (top and bottom) * Water filling hose, Germany Bedpfezcfzwjx Abtedg * Standard paint RAL 2011 municipal orange * Noise reduction package (only for exhaust fan) * Automatic central lubrication system instead of manual central lubrication * Protection for the rotating beacon * Oil service and maintenance performed at 4,850 operating hours Other: * Trade-in and purchase of vehicles and machines possible. * Selling price excluding transport and delivery. * No liability for printing and typographical errors. * Subject to errors, changes and prior sale. * Offer is non-binding. * Photos may vary. Price applies to the existing condition. * All information without guarantee.

Year of construction: 2021, condition: ready for operation (used), functionality: fully functional, EV Car Motor Assembly and Testing Line (2021) Designed to produce EV motors in the power range of 180–300 kW Including manual, semi-automated, and automated operations Cycle time: 86s Stations and Equipment Component loading - KUKA KR15 R2700-2/FLR robot (2021) - Material infeed - Inner housing heating with induction coil up to 240 °C - Stator pressing into housing - 1T TOX press - Keyence CA-DQP25X - Cooling tunnel - Cooldown to 24 °C - Cycle time: 600 s X-ring and D-ring inner housing assembly - X-ring and D-ring seal insertion into housing - Dedicated round assembly tool available Outer housing pre-assembly - Flange screw into housing with Bosch Rexroth ESA013G-G0 screwdriver - Automatic inner and outer housing joining Outer housing assembly - 3T TOX EQK 030 press - 2x Cognex scanners - 2x Keyence Camera V3 - 3x VS camera systems Rotor magnetization and measurement - Magnet magnetization - MagSys magnetizer MC3K82 (2020) - Magnetizing fixture MFFer8/160/250 A-shield pre-assembly and rotor insertion - Rotor bearing and resolver pressing - 3T TOX press A-shield assembly into outer housing - 1T TOX EQK press - A-shield screwing into outer housing with pneumatic screwdriver (5 Nm) Mounted component fastening - Fastening with 4GE59 Rexroth screwdriver - Manipulator system Handyflex 400 Inter-connector connection - Manual mounting of inter-connector and insulating tube Counter ring insertion, cooling cover, and vent assembly - 3T TOX EQK 030 press Rotor cooling cover mounting Bdjdpfx Aszhub Aobtsg - Screwing with 4 Nm End-of-line (EOL) electrical testing loop - 5x Deutronic testers, including: - ETL ATS 400 high-voltage testers - HIOKI RM3545 resistance testers - Reilhofer EOL analyzers Inter-connector disconnection station - Disconnection of the inter-connector - Insertion of 2 screws and screwing with Rexroth screwdriver (13 Nm) - Manipulator system Handyflex 300 - Washer control - Motor rotation Leak testing - 2x Leak test stations with Innomatec LTC-902 testers - Vacuum and overpressure leak tests - Tested quantity: approx. 50,000 pcs per test station Rotation, laser marking, stamping, engraving, and inspection - ADT stamping machine - Arex Laser 450 - Keyence CA-H camera system - Datalogic CBX 100 reader - Tested quantity: approx. 130,000 pcs Transportation protection - Yellow transportation cover/cap and plug assembly - Manual insertion of caps and hole securing Packaging and final inspection - Dalmec manipulator (2022)

Condition: used, Year of construction: 2014, Used Machine Year of manufacture: 2014 Condition: The machine has been factory-overhauled by Ganner Features and Technical Specifications: Complete standard configuration including: - Support with linear guide consisting of: 1 single-spindle horizontal drilling unit, 0.65 kW motor, 70 mm stroke Tool speed selectable via operator software (3000/5000/8000 rpm) 1 blow-out, gluing, and dowel-driving station for dowels Ø 8 mm, dowel length 25–50 mm - Fully automatic, electronically controlled central lubrication - X-axis NC-controlled, with working length 1300 mm, travel speed max. 105 m/min. - Z-axis manually adjustable via mechanical digital counter, position adjustable via support table 5–40 mm - Dowel drive-in overhang adjustable from 7–20 mm via a mechanical digital counter; drilling depth from 0–35 mm (for drill bit length GL 70 mm) is automatically adjusted with the drive-in overhang Bdodozlbrvspfx Abtjg - Closed glue system with 6 bar glue pressure via glue nozzle, for glues with a viscosity of 150 to 350 mPas - Glue quantity continuously adjustable via operator software - GLUE/WATER selector switch for flushing the glue system, each with: 1 stainless steel tank for 7.5 kg of glue and 7.5 l of water - Indicator light showing remaining glue levels in the glue tank - 1 left side stop, 1 right side stop, and 1 center stop (all removable) - 4 start buttons for individual processing of 1–4 workpieces - 4 pneumatic 10° angle clamping cylinders for workpiece thicknesses up to 80 mm, workpiece length (Y) min. 70 mm - 1 extraction funnel, connection Ø 80 mm - 1 TCT control unit with: Built-in industrial PC, including Beckhoff TWINCAT soft PLC, operating temperature range 0–50°C, 15-inch capacitive TFT industrial touchscreen, operating system: WINDOWS 7 - Programming via menu-driven user software, drilling distances freely programmable with ABSOLUTE, RELATIVE, or GRID dimensions, automatic workpiece mirroring and operation optimization, 4 work areas assignable to different programs, graphical workpiece display, parametric programming, zero-point offset, programmable worklists, error diagnosis with plain text Optional equipment: - 1 electronic, optical glue monitoring system G.I.C. (Glue Insert Control) for 1 glue nozzle - 1 Z-axis with NC-controlled, dynamic positioning for height adjustment of the drilling and dowel-driving station (programmable from 5–40 mm), travel speed max. 30 mm/sec. - 1 single-spindle vertical drilling unit drilling from the TOP, 0.65 kW, (3000/5000/8000 rpm), position (Y) manually adjustable via a mechanical digital counter from 5–40 mm, drilling depth (Z) max. 30 mm (with drill bit length GL 57 mm), Workpiece thickness (Z) max. 50 mm, workpiece length (Y) min. 130 mm (including drilling depth compensation, e.g., for Häfele Minifix) - 4 vertical 10° angle clamping cylinders with mount - 1 keypad with mount Availability: available shortly Location: DE-63934 Röllbach

Condition: used, mileage: 1,40,278 km, power: 96 kW (130.52 HP), first registration: 05/2019, fuel type: diesel, overall weight: 3,500 kg, color: white, gearing type: mechanical, emission class: euro6, number of seats: 3, total length: 7,030 mm, total width: 2,115 mm, total height: 3,065 mm, loading space length: 4,377 mm, loading space width: 2,044 mm, loading space height: 2,146 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), soot filter, tail-lift, Errors and prior sale excepted! Internal number: 1082. 2K50928 ----EQUIPMENT * SCHUTZ vehicle body with box body * SÖRENSEN tail lift * Reverse camera * Seat belts: 3-point height-adjustable seat belts with pyrotechnic belt tensioners * ABS * Storage: - Storage compartment under driver’s seat (not with seat base cover) - Storage compartments in front doors - Recess above glove compartment - Storage compartments above ventilation outlets in the center dashboard - Removable container under passenger seat - Right lockable glove compartment (5.3 dm³) - Lockable center storage compartment (11.38 dm³) * Driver’s airbag * Interface box for body manufacturer * Exterior mirrors, incl. integrated side indicators and wide-angle inserts * Mechanical brake assist * Rev counter * Electronic Stability Program (ESP) incl. ASR with indicator - Hydraulic brake assist - Hill holder (automatic hold for hill starts) - Load Adaptive Control (adjusts ABS, ASR, and ESP functions to vehicle load) * Power windows front, with comfort function for driver’s side * Transmission: 6-speed manual * Headrests (3) * Paint: solid color * Steering wheel with reach adjustment * Manual headlight leveling * Multifunction display with clock, warnings for headlights on and preset speed limit exceeded, and onboard computer * Particulate filter: diesel soot filter * Upholstery: fabric * Radio pre-wiring (cables and antenna) * Black side protection strips Bdedpfx Asyht H Esbtsg * Power steering * Seats: passenger double bench seat with folding table in center backrest * Seats: driver’s seat with longitudinal, height and backrest adjustment, armrest, and lumbar support * 12V socket in center console * Service interval display * Immobilizer with transponder * Central locking with high-frequency remote control ... and much more. ----The vehicle is in unprepared condition! Nationwide delivery available for an additional charge. Errors and prior sale excepted. We are happy to accept your vehicle as trade-in. Financing / Leasing possible even without down payment! Do you have any questions? We are happy to advise you!

Condition: ready for operation (used), Year of construction: 2011, travel distance X-axis: 730 mm, travel distance Y-axis: 730 mm, travel distance Z-axis: 880 mm, table load: 500 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 22,000 W, number of axes: 4, This 4s MORI SEIKI NHX 5000 was manufactured in 2011. It features a dual pallet system with a pallet size of 500 × 500 mm and a maximum pallet load of approximately 500 kg. The spindle speed reaches up to 12,000 rpm, with a tool magazine capacity of 40 tools. If you are looking to get high-quality machining capabilities, consider the MORI SEIKI NHX 5000 horizontal machining center we have for sale. Contact us for further details. • Pallet system: Dual pallet; size 500 × 500 mm; max load ≈ 500 kg • Tool system: Magazine 40 tools (optional 60 / 120); tool-to-tool ≈ 0.9 s; chip-to-chip ≈ 2.8 s • B-axis: Continuous 360°; indexing resolution 0.001° Bdjdpfxjyh Hzye Abtjg • Rapid traverse (X/Y/Z): ≈ 60 m/min • Accuracy/Construction: High-precision linear guides; thermal displacement control system; glass scales (depending on configuration) Technical Specification Taper Size BT 40

Condition: used, Year of construction: 2021, Horizon AFC-566 AKT Automatic Combination Folder, Used The Horizon AFC-566 AKT is a powerful and versatile automatic combination folder, ideal for producing brochures, inserts, pharmaceutical products, and other demanding folding jobs. Key Features: - 6 fold plates, 1 cross-fold, and 2 fold plates under the cross-fold for a variety of folding patterns - 17 pre-programmed folding patterns, easily selectable via the large color LCD touchscreen - Fully automatic setup for quick job changes and minimal setup times Bdodpfxszilb Ns Abteg - Horizon's advanced rotary suction air feeding system for fast and consistent sheet feeding - Folding rollers made of a combination of steel and soft polyurethane for superior grip and sharp, consistent folding Technical Specifications: - Max. sheet size: 558 x 850 mm (up to 1,100 mm with optional extension table) - Min. sheet size: 128 x 148 mm - Paper weight: 35 to 220 g/m² - Belt speed: 30 to 230 m/min (cross-fold 180 m/min) - Production speed: up to 42,000 cycles/h (suction head), 21,000 cycles/h (cross-fold) - Power supply: 230 V, 50/60 Hz All-Inclusive Service Package We take care of everything: from secure packaging and transportation to customs clearance. Upon request, we can also provide a customized leasing offer. Sustainable and Economical Choose a used machine and benefit twice: Save the environment and your budget. Despite possible signs of use, you receive a quality product at an attractive price.

Condition: good (used), Year of construction: 1993, Omga Pneumatic Corner Frame Assembly Machine Model: Joint 502 Bdjdpfoyy S Uaex Abteg For assembling popular types of frames. During the stapling process, the machine operator has a clear view of the frames and can, if necessary, make required positional adjustments. The two frame components are placed into the stop and locked in position by a pneumatically actuated clamp equipped with a special rubber pad to prevent damage to delicate frames. The stop is adjustable, allowing for the insertion of two staples at the desired distance. The Joint 502 allows for two different staples, even of different sizes, to be inserted at the required axial spacing, with the two staple units positioned accordingly. Location: Available from stock, 54634 Bitburg - available immediately -

Condition: like new (used), functionality: fully functional, This is a tray rack from the premium manufacturer Rational, suitable for the iCombi Pro/Classic combination steam ovens, size 20-2/1 GN. This tray rack comes from a training area and has 17 x 1/1 GN inserts with a rail spacing of 74mm and is in almost new condition. The recommended retail price (RRP) including VAT is: €3,184, our special price: €1,725 including VAT. You will receive an invoice with VAT shown separately. Service: We will be happy to assist you in arranging a certified Rational customer service technician. Are you looking for a specific Rational appliance model? Ask us, we have access to a wide range of used and new products. We will be happy to advise you on all appliance types. Our used equipment service for you: * 6 months warranty on electrical parts, limited to the replacement of defective parts, excluding installation and removal costs. * High-quality branded equipment at fair prices. * Professional overhaul/inspection and expert cleaning. * Tested and fully functional - or your money back. * Flexible shipping or self-collection options. * Competent advice - before and after the purchase. * Provision of operating instructions, connection diagrams & spare parts. * Inspection according to DGUV V3. Technical data: * W x D x H: 772 x 1742 x 1013 mm * Clearance from the lowest insert to the oven opening: 118 mm * Clearance from the highest insert to the oven opening: 148 mm * Max. insert height: 1.60 m * 17 inserts * Max. load capacity: 180 kg * Max. load capacity per insert: 30 kg * Design with container locking mechanism * Can be loaded from both sides * Tip protection when pulling out the containers using U-rails * 4 tandem swivel casters (2 with parking brake - metal parts made of stainless steel) * Drainable and removable drip tray * Rail spacing 74 mm * Removable handle * Material: Stainless steel * Article number: 60.22.396 Capacity: * 2/1 GN baking and roasting trays 17 x * 2/1 GN grids 17 x * 2/1 GN 20 mm deep 17 x * 2/1 GN 40 mm deep 17 x * 2/1 GN 65 mm deep 17 x * 2/1 GN 100 mm deep 8 x * H6-1/1 (up to 1,800g) chicken - superspike 12 x * H8-1/1 (up to 1,300g) chicken - superspike 12 x * Use of other containers: 2/4 GN, 1/1 GN Condition: used, fully functional Shipping: Bdjdpfoy Aui Eox Abtjg * Delivery or self-collection by arrangement * Worldwide shipping on request * Shipping to islands or mountain stations only by arrangement Subject to changes and errors. Do you have any questions, would you like to request a consultation, or would you like to view something on site? You can reach us by telephone during our opening hours: Monday-Friday 09:00 - 13:00 and 14:00 - 17:00. The sale is made exclusively subject to our general terms and conditions (GTC).

Condition: new, Year of construction: 2026, functionality: fully functional, warranty duration: 12 months, input voltage: 230 V, measuring range X-axis: 200 mm, measuring range Y-axis: 85 mm, measuring range Z-axis: 50 mm, total width: 483 mm, total length: 598 mm, total height: 464 mm, overall weight: 64 kg, input current: 5 A, repeat accuracy: 0.005 mm, input frequency: 50 Hz, Equipment: CE marking, USB port, documentation/manual, type plate available, PG1000-400 – Optical system for inspecting the geometry of rotating cutting tools PG1000-400 is a professional optical measuring and inspection system for quickly checking the geometry of cutting tools. It is designed for tool manufacturers, sharpening shops, grinding shops, tool rooms, CNC machining centers, and quality control/metrology departments. Its main application is the inspection of rotating cutting tools after manufacturing, grinding, sharpening, or reconditioning. The system is suitable for HSS and solid carbide tools, especially drills, end mills, step drills, reamers, taps, form tools, micro tools, and custom-made tools. The device can also be used to inspect carbide inserts, selected thread geometries, screws/bolts, and other precision parts, provided that the geometry being inspected is optically accessible to the camera. The system's primary focus is on the inspection of cutting tool geometry. Typical applications: - In-process inspection directly at the grinding machine or in production - Incoming and outgoing inspection of tools - Inspection after sharpening/regrinding - Quality documentation and measurement reports - Repeated inspection of serially produced tools PG1000-400 allows for the inspection of, for example: - Rake angle and clearance angle - Helix angle - Point angle for drills - Radii and corner radii - Diameters and distances - Cutting edge length - Land width, margin width, facets - Web thickness - Tool profile - Runout - Condition and wear of the cutting edge - Comparison of geometry with DXF/DWG drawings The system operates optically and non-contact. This is advantageous when inspecting sharp edges, fine microgeometries, coated tools, and precise edges, where speed, repeatability, and minimizing operator influence are important. The system includes REACTION software, developed specifically for the inspection of cutting tools. The software offers more than 50 measuring functions, edge detection, automatic alignment of measuring points to the edge, saving inspection scenes, comparison with DXF/DWG geometry, PDF reports with PASS/FAIL evaluation, and data export to Excel/CSV. Technical specifications: - Recommended tool diameter: 0.635–75 mm - Tool measuring length: approx. 190–200 mm - Magnification range: 12.5× to 145× - Camera: 5 MP - Monitor: 27" 4K Ultra HD - Measuring range: 85 mm vertically × 200 mm horizontally - Accuracy/repeatability: ±5 µm at maximum magnification - Device dimensions: approx. 598 × 483 × 464 mm - Weight: approx. 64 kg Offered configuration: - PG1000-400 optical cutting tool inspection system - M / F / A encoders - PC with REACTION software - 27" 4K Ultra HD monitor - Flexible LED lighting with diffuser - Curved magnetic diffusion plate Bedszdz S Tepfx Abtedg - Rotating base block for clamping fixtures - 1000-026-5"-ASS – 5" V-block assembly with insert, top clamp, and stop - Basic remote operator training About the manufacturer: PG1000 is based on the long-term development of systems for inspecting cutting tools. The first generation of PG1000 was introduced in 1993. The system is manufactured in the USA by PG Inspection Technologies LLC, which specializes in this product line. Since 1996, more than 1000 PG1000 systems have been delivered. Condition and delivery: - New machine - Year of manufacture: 2026 - Warranty: 12 months - Location: Czech Republic / EU - Delivery, assistance with commissioning, and training according to agreement - CE marking and relevant EU documentation The device i

Condition: used, Year of construction: 1992, Guilliet C four-sided milling machine, year of manufacture 1992, in good condition, including 3 milling heads (1 x 135 x 100 mm, 2 x 180 x 100 mm), including reversible cutting inserts. Bedpfxjzq Db Ds Abtedg

Condition: ready for operation (used), Trumpf 1488573 control SW V 6.2 / HW Index C1 SN:00569, used, normal signs of use, 100% functional, scope of delivery as per photos Bdjdpfx Aszu Hlasbtjg

Condition: used, Year of construction: 2003, functionality: fully functional, For sale: OKUMA MB-500H CNC Horizontal Machining Center Year of manufacture: 2003 Reliable and robust Japanese horizontal machining center equipped with an automatic 2-pallet changer, through-spindle coolant, and chip conveyor. The machine is in working condition and can be inspected under power at our facility in Croatia. Bdedpozxq Itefx Abtsg TECHNICAL DATA Manufacturer: OKUMA Model: MB-500H Year: 2003 Machine type: CNC Horizontal Machining Center CNC control: OKUMA OSP WORKING AREA X-axis travel: 800 mm Y-axis travel: 800 mm Z-axis travel: 800 mm Distance from pallet surface to spindle center: 70 – 870 mm Distance from pallet center to spindle nose: 150 – 950 mm PALLET / TABLE Number of pallets: 2 Pallet size: 500 × 500 mm Maximum pallet load: 500 kg Pallet changer: Automatic rotary pallet changer (APC) Table indexing: 1° Pallet surface: 24 × M16 tapped holes The automatic 2-pallet system allows the next workpiece to be set up while the machine is running, significantly reducing non-productive setup time. SPINDLE Spindle speed: 50 – 15,000 rpm Spindle taper: SK40 / MAS 403 SK40 Spindle motor power: 26 kW / 18.5 kW continuous Spindle bearing diameter: Ø70 mm Through-spindle coolant (TSC) AUTOMATIC TOOL CHANGER Magazine capacity: 40 tools Tool holder: MAS SK40 Tool selection: Memory random Maximum tool diameter: Ø75 mm Maximum tool diameter without adjacent tools: Ø145 mm Maximum tool length: 350 mm Maximum tool weight: 8 kg FEED RATES Rapid traverse: up to 90 m/min Cutting feed rate: 1 – 60,000 mm/min EQUIPMENT Automatic 2-pallet changer (APC) 2 × 500 × 500 mm pallets Through-spindle coolant (TSC) Chip conveyor Automatic tool changer 40-tool magazine BT40 spindle Full machine enclosure Coolant system CONDITION The machine has been used in our own production and has been regularly maintained. Machine is fully operational and can be inspected under power. Location: Croatia Inspection and test run are possible by appointment. Additional photos, videos, and information are available on request. Loading/transport can be discussed separately. Price: on request / negotiable

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, machine/vehicle number: 1205-H740-00, overall weight: 6,000 kg, travel distance X-axis: 500 mm, travel distance Y-axis: 100 mm, travel distance Z-axis: 50 mm, controller model: ANDRONIC 2060, No minimum price – guaranteed sale to the highest bidder! Submitting a bid obligates you to collect the item within the specified period, between October 7, 2026, and October 14, 2026! TECHNICAL DETAILS Travel range, X-axis: 500 mm Travel range, Y-axis: 100 mm Bodpfx Abozu Iwwstodg Travel range, Z-axis: 50 mm Travel range, Z-axis: ±50 mm, relative to the central axis of the rotary indexing table / 200 mm Travel speed, X-axis: max. 30 m/min Travel speed, Y-axis: max. 20 m/min Travel speed, Z-axis: max. 30 m/min Acceleration, X/Y/Z-axis: 10 m/s² MACHINE DETAILS Control model: ANDRONIC 2060 Dimensions & Weight Dimensions (L x W x H): 2,500 x 1,650 x 2,700 mm Total weight: 6,000 kg Operating voltage: 230/400 V Frequency: 50 Hz Rated apparent power: 12 kVA Swivel radius, control panel: approx. 1,050 mm

Condition: used, Year of construction: 2015, functionality: fully functional, Model: OKUMA MULTUS U3000 2SW 1500 (CNC turning and milling center) Control: OKUMA OSP-P300S Turning length: approx. 1,500 mm Max. turning diameter: up to 650 mm Tool system / interface: HSK-A63 Main spindle: Drive power: 22 kW Torque: 427 Nm Max. speed: 5,000 rpm (2 gear stages) Spindle nose: Short taper size 6 Bodpfxezu I U Ao Abtsdg Spindle front bearing: Ø 120 mm Spindle bore: Ø 80 mm 3. Counter spindle (Okuma motor spindle) Travel: Traversable on the W-axis Drive power: 22 kW Torque: 427 Nm Max. speed: 5,000 rpm Spindle nose: Short taper size 6 Spindle front bearing: Ø 100 mm Spindle bore: Ø 62 mm Tool spindle / Milling spindle (Okuma motor spindle) Drive power: 22 kW Torque: 120 Nm Max. speed: 12,000 rpm Tool holder: HSK-A63 Axes & Travel Ranges C-axis: 360° (Indexing / Positioning in 0.001° increments) Y-axis: Stroke +125 mm / -125 mm (Total stroke 250 mm) B-axis: 240° (Indexing / Positioning in 0.001° increments) Tool magazine & Turret Tool Magazine (ATC): 120 positions Lower turret: 12 stations with direct mounting system "radial" Turret guides: ZB-axis with cylindrical roller linear guide XB-axis with slide guide Coolant supply / Internal coolant supply (ICS): max. 20 bar (including bag filter) External cooling for tool spindle: max. 8 bar Accessories: Short loader LNS Quick Load Seri O III

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: DT1UE18105029734, This Rational Ultra Vent hood for Rational combi-steamers, including the connection kit, is suitable for CMP and SCC 61/101 electric combi-steamers manufactured from 2011 to the present (index H+I). The hood has been inspected in our in-house workshop and is fully functional. The hood has dents and scratches on one side panel due to improper transportation. This does not affect the hood's functions; however, for this reason, we offer it at a special price. The list price for this Ultra Vent hood is €3,696 net. Service: We will gladly assist you in finding a certified Rational customer service provider. Are you looking for a specific Rational appliance type? Ask us; we have access to an extensive range of used and new equipment. We will be happy to advise you on all appliance types. Our used equipment service for you: * 6-month warranty on all electrical parts, limited to the replacement of defective parts, excluding installation and removal costs. * Professional overhaul/inspection & expert cleaning * Inspected & fully functional - or your money back * Flexible shipping or self-collection options * Competent advice - before and after purchase * Provision of operating manuals, connection diagrams & spare parts * Inspection according to DGUV V3 This Ultra Vent hood features patented condensation technology, which captures and removes vapors. Complex measures for exhaust system installation are a thing of the past. An external connection is completely eliminated. Installation is simple and can even be done retroactively. Technical data: * W x D x H: approx. 854 x 1226 x 470 mm * Power connection: V: 230 / Hz: 50-60 * Weight: approx. 55 kg * Serial number: DT1UE18105029734 * Year of manufacture: 2018 Bdedpozu Sffsfx Abtjg Condition: used, fully functional Shipping: * Delivery or self-collection by arrangement * Worldwide shipping on request * Shipping to islands or mountain stations only by arrangement Subject to changes and errors. Do you have any questions, would you like advice, or would you like to see something on-site? You can reach us by telephone during our opening hours: Monday to Friday, 9:00 a.m. to 1:00 p.m. and 2:00 p.m. to 5:00 p.m. Sales are subject exclusively to our general terms and conditions.

Condition: ready for operation (used), Casadei R63h3 Thickness Planer Bdodpjzv Dnzofx Abteg Maximum planing height: 300 mm Minimum planing height: 4 mm Feed speed: 5-25 m/min, stepless Planer cutterhead diameter: 120 mm Table dimensions: 1000 mm, mounted on 4 columns 4 cutterblocks with insertable knives, including setting gauge 2 feed rollers Electric height adjustment Weight: 1000 kg

Condition: used, axle configuration: 2 axles, first registration: 03/2025, next inspection (TÜV): 03/2027, loading space length: 3,320 mm, loading space width: 2,350 mm, loading space height: 600 mm, total width: 2,420 mm, total height: 410 mm, Year of construction: 2025, Vetter TRG 8120 / TRA 8120 Cable Drum Variable Trailer, 1 owner, low usage, not used on construction sites, as new condition. TRA 8120 tandem trailer for the Subduct Drum Frame TRG 8120: - Height-adjustable overrun drawbar with DIN towing eye and jockey wheel, including interchangeable ball hitch coupling. - 2 rear telescopic crank supports. - Floor made of phenolic resin-coated plywood with mounting points for securing the frame. - Ramp slot for inserting aluminum ramps. - No drop sides, no aluminum ramps included. Bdedpozxix Rsfx Abtjg - Trailer TÜV-certified. - Vehicle ID No.: WHC2PHTXXRN623360 Payload: 1200 kg Unladen weight (approx.): 800 kg Gross weight: 2000 kg Drawbar load: 100 kg Platform internal width: 2350 mm Trailer overall width: 2420 mm Platform internal length: 3320 mm Maximum trailer overall length: 5550 mm Loading height: 600 mm Coupling height: 410 mm Tyres: 4x 195/55 Additional equipment: aluminum side panels, 300 mm high, including APR Board hinges, for trailer TRA 8120. Optional extras: Aluminum ramps 2500x600x55 mm, APR Ramp. Surcharge for 2 aluminum ramps, each 2500x300x55 mm, coarse, for trailer TRA 8120. - Permissible load per ramp pair: axle spacing 2.0 m = 1400 kg; axle spacing 1.5 m = 1400 kg; axle spacing 1.0 m = 1220 kg; single axle = 900 kg Net purchase price: €696.00 + 19% VAT TRG 8120, drum transport and 1 pay-off frame for up to 8 subduct drums on trailer TRA 8120 or on truck beds. The frame can also be placed on the ground at the worksite and the drums unwound. Drums from various manufacturers can be accommodated: - Up to 8 drums, diameter 1200 mm - Max. drum width: 440 mm - Max. payload: 2000 kg The frame is equipped with: - 2 lightweight aluminum drum axles - 6 spacers - 4 clamping collars for 2 shafts - 1 rear portal for deflection piping Advantages of the frame: - Usable on a range of vehicles - Can be placed directly on the ground - Fully disassemblable, bolted construction - Completely hot-dip galvanized and robust Technical data: Length: 2770 mm, Width: 2330 mm, Internal width: 2160 mm, Height: 770 mm, Weight approx. 277 kg Former net new price: €16,892 + 19% VAT Despite the utmost care, errors in this advertisement cannot be excluded. Errors and prior sale reserved!

Condition: used, Technical details: drum diameter: 400 mm revolutions per minute: 980 U/min total power requirement: 2,2 kW Lanner batch wringer ME41-2 for deoiling of metal chips -turnkey delivery and easiest handling -very long service life, operation free of vibrations -compact and easy to maintain, i.e. low maintenance costs and quick return of investment Bdodpfoft Tipex Abteg -standard execution consists of lid with pneumatic spring and electro-magnetic lid locking , unbalance detection switch and standstill control -including control cabinet laterally placed, i.e. not in swivel range of crane -drum volume 35 Liter/max. 50 kg -rotation speed max. 980 min-1 -power 2,2 kW Painting: RAL 5012 light blue (batch wringer, crane support) RAL 1003 signal yellow (traverse) RAL 7035 light grey (control cabinet) In each case silk gloss. Changes after consultation. Also included in the scope of delivery: -Crane support with swivel arm: mounted on the side of the centrifuge housing. For lifting the insert drum out of the centrifuge. -Electric chain hoist: with control pendant for suspension of the crossbeam, max. load 250 kg. Designed for indoor use -Lifting beam: for lifting the insert drum. -Documentation on CD-ROM and in paper form Optional for extra charge: -Additional insert drum with pivot, perforation: ø 3 mm -Tank with 100 L capacity for the spun-off liquid. With pump, electric control, float switch and drip tray This is not a used machine! Please, contact us for getting more information and pictures on mail(at) or *