Used Liquid Fertilizer for sale (1,606)

Year of construction: 2017, condition: used, Power: 5 kW (7 HP) Capacity: 218 m^3/h Tank pressure: 33 bar Bjdpfxjx At Aho Addsdk Manufacturer : Sihi Flowserve Model LPHX 45316 AB Year: 2017 Type : Liquid ring vacuum pump Ability to pump almost all gases and vapours Possibility of pumping liquid and gas simultaneously Motor power: 5.5 kW ATEX classification: EX II 2G cbk HB TX Speed: 1450 rpm Suction pressure: min. 33 mbar Air volume: 218 m3 / h  

Condition: ready for operation (used), functionality: fully functional, Actuator for Ball Valve (EX Limit Switch) Brand / Model: Masoneilan / Dresser (USA) – Compact II actuator + SV12-111114 limit switch (ATEX Ex d IIB T6, IP66) Application: Automatic opening/closing of ball valves in gas, air, steam, or liquid service (electric / pneumatic control). Technical Specification Operating pressure: ≤10 bar Torque: approx. 80–150 Nm (depends on actuator size shown in photos) Temperature range: –40…+85 °C Electrical signal: 30 VDC, 4–20 mA Protection: ATEX / EX certified, flameproof enclosure (Ex d) Ingress protection: IP66 Limit switch: Masoneilan / Dresser SV12-111114 (EX d IIB T6) Typically supplied with: stainless-steel ball valve (DN/PN depending on installation) Condition Very good mechanical state Bdsdpfexy Rn Nex Addok Stainless flanges clean and tight Proper sealing and no corrosion on EX housing Photos confirm intact labels, clear ATEX marking, and correct installation orientation

Condition: used, Year of construction: 2006, Used Filling Monoblock BERTOLASO OLIMPIA 12/12/1 up to 2000 bph This Monoblock  offers a bottling unit manufactured by Bertolaso in 2006. Although designed to operate at a maximum speed of 2000 bottles per hour (BPH), operators have never used it, leaving it in very good condition. Furthermore, the Olimpia 12/12/1 monoblock efficiently handles glass containers, allowing for both 0.75 and 1.5-liter formats, and performs especially well for bottling still wine and beer. Rinsing System of the Used Filling Monoblock OLIMPIA 12/12/1 The Used Filling Monoblock BERTOLASO OLIMPIA 12/12/1 up to 2000 bph achieves rinsing through a gripper system equipped with 12 clamps for glass containers. In fact, this system ensures uniform container cleaning before filling. Moreover, its single-type treatment prepares containers efficiently, maintaining the final product’s integrity. This configuration controls the rinsing flow stably, achieving efficiency even in high-intensity work environments. Filling Technology: Gravity Valves with Light Depression The Monoblock BERTOLASO integrates 12 valves that fill containers using gravity, supported by light depression, ensuring precise liquid dosage. Consequently, this method minimizes air presence in the container, which helps preserve product quality and increases storage stability for wine and beer. Fixed Nozzles for Consistent Filling Bsdpfjvgvfkox Addjdk Additionally, the fixed nozzles of the Filling Monoblock BERTOLASO maintain stable, continuous filling, ensuring homogeneous liquid distribution in containers. As a result, this design enables the monoblock to handle high volumes efficiently, therefore reducing product waste and optimizing production processes. Operational Condition and Storage State The Used Filling Monoblock BERTOLASO OLIMPIA 12/12/1 up to 2000 bph remains in storage, having never been activated. Thus, this storage state keeps all components in pristine condition, so they are ready for immediate operation. Therefore, it serves as an ideal solution for those seeking a ready-to-use bottling monoblock without wear or restoration requirements. Production Advantages of the Used Filling Monoblock OLIMPIA 12/12/1 The Monoblock BERTOLASO adapts especially well to production lines requiring flexibility for different container formats and bottled products. In particular, its ability to manage various container sizes (0.75 L and 1.5 L) expands its applications, making it a versatile choice. Finally, the machine’s overall design enhances efficiency, ensuring high performance during production runs.

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, Brand: SCM Model: OLIMPIC K 500 T/ER-2 - CE Automatic edge banding machine with sanding unit for wooden, veneer, PVC, melamine, ABS edges – suitable for furniture manufacturing, joinery, custom fittings, panels, kitchens, bathroom furniture, and various other applications Technical specifications: Bdedpfjxnvr Aex Addek Min./max. panel height: 8–60 mm Panel height with corner rounding unit: 10–45 mm Edge thickness: 0.4–8 mm Edge thickness from coil: 0.4–3 mm Minimum panel width: 55 mm Feed speed: 11 m/min Pressure beam with motorized vertical movement Panel support rail Sound-insulated safety enclosure Fluid inlets Components: Anti-adhesive spraying unit with two nozzles – two tanks for anti-adhesion liquid Pre-milling units with two high-frequency motors – H64 mm diamond tools – diameter 100 mm, bore 30 mm, height 65 mm – copying set Gluing unit VC 560 for edge application on panels up to 60 mm – glue pot capacity: 1.5 kg – exchangeable glue pot End trimming unit with two independent motors, each 0.35 kW at 12,000 rpm – motor tilt from 0° to 15° – 2 saw blades, diameter 115 mm – front copying devices Tilting trimming/bevelling unit for removing top and bottom edge overhang – 2 motors at 0.55 kW – 12,000 rpm – tilt range from 0° to 25° – two-position pneumatic set for quick change between thin or radius edges Corner rounding unit with two motors on prismatic guides – for rounding and trimming thin or thick edges – 2 motors at 0.55 kW – 12,000 rpm Edge scraping unit for optimal finishing of ABS/PVC edges with rotary copying and extraction hood, scrap collection cassette Glue scraping unit – removes glue residues from the lower and upper panel surfaces Buffing unit for cleaning and polishing plastic edges – motor 0.25 kW – brush diameter 150 mm Compressed air: 7 bar Overall dimensions: 5500 x 1150 x 1550 (H) mm Weight: 1,780 kg Recently serviced New diamond pre-millers New copying wheels...

Condition: excellent (used), Year of construction: 2006, operating hours: 2,988 h, functionality: fully functional, travel distance X-axis: 500 mm, travel distance Y-axis: 255 mm, travel distance Z-axis: 147 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, table width: 320 mm, table length: 885 mm, table load: 250 kg, overall weight: 2,450 kg, spindle speed (min.): 50 rpm, spindle speed (max.): 9,000 rpm, operating hours of spindle: 2,988 h, spindle motor power: 9,900 W, Equipment: documentation/manual, rotational speed infinitely variable, type plate available, FEHLMANN PICOMAX 55 CNC Vertical Machining Centre with Heidenhain handwheel, RENISHAW MP-15 probe, 60 pcs. SF 32 tool holders and 97 pcs. collets. The machine comes from the liquidation of a German company. The machine has been fully inspected and is in excellent, well-maintained condition, immediately ready for operation! The spindle runs very smoothly at all speed ranges. The guideways and spindle drives operate flawlessly. The FEHLMANN Picomax 55 2/3 CNC milling machine is a Swiss-made machine, designed for high-precision machining applications. It is optimized for micro-machining in small and medium-sized batches for tool and mould making. Condition: Very good, fully functional. Location: Graz, Austria Availability: Ex stock Technical data: Model: FEHLMANN PICOMAX 55 CNC Year of manufacture: 2006 Operating hours: Only 2,988 h Controller: HEIDENHAIN iTNC 530 Travels: X-axis: 500 mm Y-axis: 255 mm Z-axis, quill manual: 160 mm Z-axis, quill automatic: 147 mm W-axis, machine head: 500 mm Measuring system: Direct linear scale measurement on X/Y/W Clamping surface: 885 x 320 mm Speed range: 50 – 9,000 rpm Tool holder: SF32 Table load capacity: max. 250 kg Spindle power (S6, 40%): 9.9 kW Machine weight: approx. 2,450 kg Dimensions (L x W x H): 1,900 x 1,900 x 2,300 mm Inclusive accessories: - 60 pcs. SF-32 tool holders (see photos) Bsdpfxovphv Tj Addodk - 97 pcs. collets (see photos) - Renishaw MP15 probe - Electronic handwheel (manual control unit) - Complete machine documentation including EC Declaration of Conformity Key features: - Swiss precision engineering, extremely durable - Very well maintained, both technically and visually in top condition - Immediately ready for use - Ideal for small batch production, toolmaking, and precision component manufacturing Note: The original purchase price with this configuration was approx. €150,000. Inspection under power is possible by appointment. Contact us for further details, pictures/videos or to arrange a viewing appointment.

Year of construction: 2025, condition: new, XX100292 New CNC Machining centre with 4 controlled axes FOM INDUSTRIE FMC 470 Machine in stock and ready for shipping Standard configuration: - Liquid-cooled electrospindle 7 kW, 20,000 rpm (HSK-F63) - 9 location tool magazine on head (HSK-F63) - No. 2 pairs of pneumatic vices with positioning through the travelling column - No. 2 pairs of low profile jaws for clamping wide profiles - Left pneumatic reference stop - Minimum quantity lubrication (MQL) with pure oil - Central automatic greasing system and device for manual greasing - Chip and waste collection tank in base - Perimeter guard system with automatically opening, front retractable doors - X FLOW (automatic orientation of lubricant nozzles) - Control: POWER-D - Movable control console - 24” display - FST CAM 4 program Optional equipment installed on the machine: - PR202941 Fixed tool magazine for 8 positions in the center on the machine base - PR202962 Device for checking the integrity and measuring tool length - ZR204058 Pendulum mode with multiple workpieces (2 work areas, 4 workpieces) and processing of non-standard lengths with X-PAL: • Two pairs of additional vices with independent positioning • Transformation of std vices into vices with independent positioning • LED bar • Profile positioning software • Software for viewing the progress of the processing cycle • Device for measuring profile length • Second X-FLOW • Right pneumatic reference stop • Pendulum control software • Safety devices for pendulum processing • Tunnel for oversized profile machining • Software to manage oversized machining operations • ''Clock'' time calculation module program - PR202971 Data import software in accordance to FOM protocol and wireless optical bar code and QR code reader - ZP715010 Module for rigid tapping and chase tapping - PR202957 Hinged belt conveyor with ramp - PR203389 Rear chip collection tank - PR202975 Tool set A3/HSK F63 - PR202967 Angle head with vertical disc Ø 230 mm Bdsdpfsiv Imnox Addok - PR202968 Cone with horizontal disc Ø 250 mm - PR204497 Holder HSKF63 with cutter Ø 200 x 6 mm - PR203072 Software adjustment of the vice pressure 3,5 - 7 bar - ZP714611 License for the office version of FST CAM 4

Condition: used, Manufacturer: Sevin Type : Mixing tank / disperser. Materials : Vessel + double jacket + heat insulation: stainless steel Feet + stirring support in steel. Volume: 575 L total / 500 L useful Bdsdpfx Aex Atqlsddsk Jacket: steam / liquid Manual central drain 2 lids / inspection hatch Mixing tool: dispersion rotor ø 250 mm Motor power : 1,1 KW – 1500 rpm Transmission : 3 x belts (new)

Year of construction: 2020, condition: ready for operation (used), This 5-axis COSMEC Conquest 515 5-AXIX-500 was manufactured in 2020. It features a robust welded steel construction for high rigidity and dual gantry motorization for precise X-axis control. Equipped with a 5-axis spindle, liquid cooling, and a 12-station tool changer, it excels in machining wood, wood-based materials, and plastics. Consider the opportunity to buy this COSMEC Conquest 515 5-AXIX-500 CNC processing center. Contact us for more information about this machine. Application Types Bjdpfx Adjxx Du Todedk CNC Wood Machining

Condition: good (used), functionality: fully functional, We are looking for company liquidations of sheet metal processing machines Bdsdpfx Ajvzl H Tjddok

Condition: used, mileage: 100 km, power: 180 kW (244.73 HP), first registration: 06/2024, overall weight: 19,000 kg, fuel type: electric, color: silver, axle configuration: 2 axles, next inspection (TÜV): 06/2026, gearing type: automatic, loading space volume: 31 m³, loading space width: 2,460 mm, loading space length: 5,430 mm, loading space height: 2,300 mm, Year of construction: 2024, total width: 2,530 mm, total height: 3,232 mm, Equipment: ABS, air conditioning, all wheel drive, electronic stability program (ESP), navigation system, parking heater, tail-lift, The ETH8 comes standard with BYD?s state-of-the-art iron phosphate battery, which has been proven in the industry to be one of the safest, most reliable and longest-lasting batteries in the world. BYD was the first in the world to industrialize the iron phosphate battery. This high-performance battery is safe, stable, environmentally friendly and has a longer lifespan. Battery Thermal Management System (BTMS): BTMS is a liquid cooling system that guarantees that the battery temperature is maintained at an optimal operating temperature. This increases the safety and reliability of the battery system and allows the vehicle to operate in extreme weather conditions. Bedpfxsw N Alaj Addjdk The ETH8 takes only 2 hours to charge from 20% to 100%. When braking or lifting the accelerator pedal (when the battery charge is lower than 90%), kinetic energy is converted into electricity, which charges the battery. This can effectively reduce brake pad wear, increase range and save energy. With a battery capacity of 255 kWh, the estimated range at full load is up to 200 km. Please call us at WhatsUp/Viber also) E-mail:

Condition: new, Circular saw blade diameter 300 mm Bore 40 mm thickness 3 mm Bdjdpomxi T Aefx Addsk Number of teeth 180 Pitch circle driver bore 63 mm diameter driving hole 11mm HSS unused ,from magazine liquidation bearing number 28418

Year of construction: 1985, condition: used, Model: NL 40AYear : 1985Type : Progressive cavity pump / Eccentric screw pumpPower : 1,1 KWCapacity : approx. 2 m3 / hFor liquid and semi-liquid products with or without solids. Bdodpsx Atk Eofx Addjk

Year of construction: 2007, condition: ready for operation (used), Main Drive Number of axis 5 Bsdpexx Dutefx Addjdk Movement X-Axis Movement 4600 mm Z-Axis Movement 275 mm Y-Axis Movement 1935 mm This 5-axis Biesse Rover C9.50 was manufactured in 2007. It features a large working area (X=4600 mm, Y=1935 mm, Z=275 mm), an automatic lubrication system, and a control unit for 5-axis interpolation. The machine includes a vacuum system, a conveyor belt for chip removal, and a liquid cooling unit. If you are looking to get high-quality CNC machining capabilities, consider the Biesse Rover C9.50 machine we have for sale. Contact us for more information. Application Types CNC Wood Machining

Year of construction: 2014, condition: used, Applicable material: Chemicals Bodpfx Aox Arz Ajddedk Power: 4 kW (5 HP) Manufacturer : Bio Inox Year : 2014 Type : Reactor / process vessel Material : stainless steel ATEX Classification: Ex II Gc Agitation : Disperssion disk Power : 4 KW Pneumatic valve + Electrical position indicator Possibility of stirring the bottom of the tank 0.55 Kw. ( Mixing device not mounted). Light for inside   Vessel : Capacity: 900L Maximum operating pressure: +50 / -5 Mbar Maximum operating temperature: 100°C Minimum operating temperature: 5°C   Jacketed : Capacity: 10 + 12L fluid : liquid / 2 Max working pressure: 3 bar Maximum operating temperature: 95°C Min operating temperature: -2°C

Condition: used, Power: 1 kW (2 HP) Volume: 500 l Mixing and coating / impregnation unit by liquid insertion under vacuum or atmospheric conditions and at con Mixer Capacity: 500 L Motor power : 1,5 KW Mixing speed : 37 rpm Type of agitation : elongated blades Maximum pressure : – 1 Barg Max temperature : 200°C Air connection Liquid insertion / spraying connection 3 nozzles free to use if required. Mounted on a tilting frame Mixer rotation: manual. Double jacket Type: heating channels Bdsdpox Aryljfx Addjk Max pressure: 14 barg Max temperature : 200°C Other Sold with platform + stairs + feed hopper.

Year of construction: 2003, condition: used, Empty weight: 650 kg Dimensions (LxBxH): 84 x 84 x 164 cm Current frequency: 50 Hz Voltage: 400 Manufacturer : Martin Christ Gefriertrocknungsanlagen GmbH Model: EPSILON 2-6D Year: 2003 Type : Laboratory and pilot freeze-dryer Applications: Dry or liquid drying in vials, bottles, ampoules, flanges, trays, etc. Examples of products: Biological products: bacteria, viruses, tissues, plant extracts / Pharmaceutical products: plasma, serum, antibodies, vaccines / Biochemical tests / Food products: ferments, vitamins General data : Pre-freezing, freeze-drying (sublimation) and final drying Vacuum application, < -10°C 3 + 1 shelves Shelf surface area: 0.3 m². Distance between shelves: 68 mm Software: SCADA Software Cleaning flange Sample extraction system Manual stopper for vials Ice condenser : Capacity: 8.0 kg Performance: 6.0 kg / 24 h Temperature: -75°C Dimensions : Width: 800 mm Depth: 840 mm Height: 1640 mm Weight: ~650 kg Energy data : Power supply: 3-phase, 400 V / 50 Hz Power consumption: max. 5.0 kVA Max. ambient temperature: +25°C Refrigerant : Types : R404A, R508, Isceon 89 Heat transfer fluid: Syltherm XLT Technical connections Warm water inlet: ½" hose connection Defrost water drain: ½" hose connection Vacuum exhaust: DN 25 stainless steel pipe Ventilation: DN 6 connection Bjdjx Arvtspfx Addedk Others : Documentation and qualifications available Sold with LPC plus computer for data analysis. Spare parts

Year of construction: 2015, condition: used, Applicable material: Chemicals Documents Technical information Physico-chemical separation / distillation unit. Year : 2015 Installation ATEX 3G IIBT4, inside the installation: zone 1G Operating mode: continuous – batch – semi-batch. Pressure: Vacuum – 3 barg max Boiler size: 50 Litres (Possible 200 Litres) Flow rates: Approximately 180 Kg/hr feeding a water/ethanol mixture (90/10) at atmospheric pressure with a reflux rate of 5. Nombre de plateaux théoriques : 20 - Alimentation possible en 3 points : 4 lits de garnissage structuré, 4 redistributeurs de liquide (dont 3 avec recentreurs) Dimensions: Unit made as a skid, in hot-dip galvanised steel frame with dimensions 2400 x2400 x 4000MM high. Utilities / sources : Steam: 3 bar eff 143°C 30 to 80kg/h Cold water 25-30°C : 2-5m3/h Chilled water 5-10°C : 0.5m3/h Compressed air : 6bar eff Bdsdpfx Aex Artfeddsk Nitrogen inerting : 4.5 bar eff Electricity : 400V tri 50 Hz IT : 5kw

Condition: used, Manufacturer: Hanovia UV Model: PMS150G4/4 Type : Ultraviolet disinfection system Application: Ultraviolet (UV) water/liquid treatment Pressure rating: 7 bar Maximum pressure loss: 0.15 bar Bdodpfex Ardqex Addek Maximum flow rate: 133 L / min - 8 m3/hour Temperature: 80°C

Year of construction: 1993, condition: used, Power: 1 kW (2 HP) Empty weight: 450 kg Cargo space capacity: 25 l Manufacturer : Glatt Model : VG-25 Year : 1993 Type: Universal high shear granulator / mixer Capacity : 25 Litres Useful capacity: 5 - 18 Litres Empty weight: 450 Kg Compressed air: 6 - 10 bar Double jacket: yes Bsdpfxex Akb Is Addjdk Water pressure: 2 - 6 bar Main mixer: 30 - 600 rpm Power : 5,5 KW Chopper: 300 - 3000 rpm Power : 1,5 KW Variable speed drive: electric x2 Liquid spraying : Watson Marlow peristaltic pump Discharge valve: Manual Mobile chassis: 4 wheels Video :

Year of construction: 2008, condition: used, // Equipment dismantled and stored in our warehouse // Manufacturer: Larox / Pannevis (Larox B.V.) Model: RT®/FT 1.15 x 5.6 m Type: Vacuum belt filter Year: 2008 (1988 version refurbished) Application: Liquid/solid separation, with cake drying and filtrate recovery. FT = Fume-Tight> Materials: stainless steel Filter area: 6.4 m² Cake cleaning: – Option to perform several washing stages, with each filtrate collected in its own receiver (purity up to 99.99% or more) with low washing water consumption. – Backwashing Repositioning of the tray and support grids at each retraction Operation/power supply: continuous Continuously washed filter cloth Cloth orientation and tensioner Extraction screw Skid with 3 filtration tanks and circulation pumps Vacuum pump skid: – Sihi Sterling LPHA 70123 (Atex) – Liquid ring: ethanol – 855 m³/h – 21.83 KW – Heat exchanger – Recirculation pump – Separator tank Bdodpfx Adex Akbzedok Main machine weight: 3000 kg Main machine length: 913 cm Full technical documentation (paper and digital versions) Electrical cabinet

Year of construction: 2000, condition: used, Power: 9 kW (12 HP) Capacity: 280 m^3/h Manufacturer: Travaini Travaini pump Model TRHB 50-280 Year: 2000 Type : liquid ring pump Number of stages : 2 Motor power: 9.2 kW - 1450 rpm Bdodpfx Ajx Ai U Teddsk Flange size: DN 50 Nominal capacity (m³/h) : 280 Documentation available

Year of construction: 2009, condition: used, Empty weight: 750 kg Cargo space capacity: 2 l Manufacturer: Romaco - Frymakoruma Model: Dinex Lab Year: 2009 Type: Vacuum mixer for R&D or small-scale production Application: liquid and/or viscous (semi-liquid) products = dispersion, homogenization, emulsion, grinding, and pumping of the product Tank: Pressure: -1 / 0 bar Volume: 18 L Temperature: 130°C Jacket: Pressure: 6 bar Volume: 2 L Temperature: 180°C Homogenizer: high-speed agitation 2 modes = Pumping with discharge / Dispersion with high shear force Tool size: 100 mm Rotor: 20 x 4 mm Stator: 30 x 4 mm VEM motor 7.5 kW / 2890 RPM Scraper mixer: slow agitation SEW 0.37 KW motor Sterling SIHI LEMA 25 liquid ring vacuum pump Power 1.1 KW - Max. 16 m³/h. CIP (clean in place) 2 x feed hoppers, 1 of which is connected to the jacket with its piping Air pressure: 6 bar Water pressure: 6 bar Temperature control regulator Single-acting seal: reconditioned by Burgmann Paper documentation Bjdpfx Ajx Ai Umeddsdk Weight: 750 kg

Condition: used, power: 4 kW (5.44 HP), color: grey, Year of construction: 2002, Field of application: Mining Volume of the tank: 0.22 m^3 Manufacturer : Comec Model: Micronet-25-COSM Year : 2002 Type : DISPERSION & MILLING MACHINE   Useful volume : 3 - 22 L Motor power : 4 kW Material : stainless steel Electrical cabinet with variable speed drive. Bjdpfex Ai Uajx Addjdk Work cycle timer for automatic stop. Double jacket Top loading of liquids Dispersion by deflocculating turbine + sand milling Continuous recirculation between the upper dispersion basket and the lower grinding chamber until the desired fineness is achieved. Cosmetic applications: Particularly suitable for the stable dispersion of oils in water, the addition of pigments and glues, and the mixing of colourants in products such as nail varnishes.

Year of construction: 2016, condition: used, // Equipment dismantled and stored in our warehouse // Manufacturer: Italvacuum Model: Cosmodry System IHD 3200 Year: 2016 Type: horizontal vacuum paddle dryer Application: drying wet powders ATEX (Eex) unit: yes Industries: Fine chemicals, pharmaceuticals (API), intermediates A) Agitation: Concentric agitator with heated shaft, removable in several segments (double mechanical seal) Transmission: (CEMP) - Power 30 kW + Gearbox + Chain Agitation speed: 1.6 ÷ 8.1 rpm Atex: explosion-proof ATEX II 2GD Mounted with the dryer on a support structure (single SKID) B) Drying chamber with discharge valve Total volume : 3200 Liters Useful volume : 30% - 80% Internal pressure : -1 / 0,5 barg Jacket pressure : 0 / 1,7 barg Project temperature : -10 / +130°C Maximum heating fluid temperature: +100°C Best vacuum tightness: 4 mbar/h EX-I absolute pressure transmitter PT100 Ex-i product temperature sensor Nitrogen backwash system Rotary chopper speed: 300 / 1200 rpm (not installed) Material in contact with the product: AISI 316L - EN 1.4404 Vacuum seals: PTFE and FEP Jacket material: AISI 304 - EN 1.4301 Heating fluid: Diathermic oil Mirror-polished interior finish (Ra ≤ 0.4 µm) Satin exterior finish (Ra ≤ 1.2 µm) Inspection and Shut-off Valve DN.1650 Buffer Relief Valve DN 200/300 DN 250 Butterfly Loading Valve Prepared for the installation of two choppers (lateral knives) C) Process filter D) Vacuum unit: SAURUS939 piston vacuum pump, model VVDPump support benchATEX: Ex-d-IIB-T4 – IP55Power: 11 kWAtmospheric pressure surface condenser, model VD200I Bdedpfjx Ai Tiox Addjk E) Vacuum condensing unit - AISI 316L stainless steel with double cooling jacket in AISI 304 stainless steel. Internal design pressure: -1 / 0.5 barg Jacket design pressure: 0 / 3 barg Design temperature: -10 / 40 °C Maximum cooling liquid pressure: 2.5 bar Exchange surface area: 8.5 m2 Condensate collection capacity: 900 litres Level sensor F) External safety filter G) Temperature control system: Heating/Cooling Steam liquid heater: Pressure 7 bar - Jacket temperature: 142°C - Surface area: 1.65 m2 Cooler, mounted on the heater: cold water or brine - Pipe jacket pressure: 12 barg - Jacket temperature: 142°C - Pipe temperature: -10°C /+ 99°C - Surface area: 3.42 m2 H) Command and Control System (Electrical Cabinet + HMI) Complete technical file

Year of construction: 2011, condition: used, Applicable material: Food Empty weight: 600 kg Dimensions (LxBxH): 150 x 120 x 230 cm Cargo space capacity: 950 l Cooling starts at: 120 °C Volume: 950 l Bdedpfjx Ai Tcjx Addjk Manufacturer : Packo Inov NV Type: Cryofreezer / Batch freezer Year of manufacture : 2011   Total volume : 950 L Dimensions : 150 x 120 x 230 cm Supply voltage 3x400V + N – 50Hz Minimum temperature set point: – 120°C Weight : 600 Kg Materials: 304 L stainless steel Full technical file: available in digital version Refrigerant : Liquid nitrogen   Previous use: 0.5 or 1L bottles containing Biological active ingredient. 0.5L bottle : o Dimensions: 72 x 72 x 180 mm (WxDxH) o Maximum capacity: 32 bottles 1.0L bottle : o Dimensions: 90 x 90 x 220 mm (WxDxH) o Maximum capacity: 32 bottles