Used Log Sorting Line for sale (12,691)

Year of construction: 2003, condition: good (used), Sorting line with 11 pockets Dedpfxexuh Sbe Aptswb

Condition: used, Vibratory Feeder with Pneumatic Screwdriver Stand Eco Line Vibratory Feeder, Sorting Device, Bowl Feeder, Vibratory Bowl, Automatic Screwdriver WEBER Type ZSU 24 Machine No.: 1113212 Year of Manufacture: 2003 Vibratory Feeder WEBER ZSU 24 Djdpsxf Up Uofx Aptewb Bowl diameter: 240 mm Bowl internal height: 70 mm Sorting track width: 10 mm Power supply: 230 Volt, 50 Hz Operating pressure: 6 bar (for singulation and screws) Control voltage for pneumatic valves: 24 Volt - Controller for infinitely variable vibration speed = infinitely variable transport speed - Vibratory bowl in protective enclosure - With pneumatic feeding system - Feed impulse via external electrical control - The feeder was used for feeding screws M5 x 12 mm - Some pneumatic hoses need to be replaced - Siemens S7-200 CPU 224 PLC MISSING Space requirements vibratory bowl L x W x H: 450 x 450 x 315 mm Vibratory bowl weight: 32 kg WEVER Eco Line Screwdriver Stand Guide column: Ø 60 x 525 mm Height adjustment: 345 mm Primary stroke pneumatic cylinder 1 FESTO DZF-32-125-P-A-SM: 115 mm Screwdriver holder diameter: Ø 50 mm Secondary stroke pneumatic cylinder 2 FESTO: 30 mm Screwdriver guide diameter: Ø 37 mm Distance screwdriver guide to table: 135 - 465 mm - 1 piece flat cylinder FESTO, Type DZF-32-125-P-A-SM - 1 piece flat cylinder FESTO, Type probably DZF-32-30-P-A-SM - Screwdriver linear motion frame on linear guide - 3 position sensors on the cylinders - Festo pressure switch - Bosch pneumatic valve Screwdriver stand dimensions W x D x H: 200 x 410 x 1050 mm Screwdriver stand weight: 35 kg good condition Total weight vibratory feeder and screwdriver stand: 67 kg Attention: The original Siemens S7-200 CPU 224 PLC is missing (see picture control cabinet without PLC), therefore, an automatic process is not possible in this condition. The control system also managed the separations of the screws and controlled the screwdriver itself. The vibratory bowl is fully functional even without the PLC, the built-in vibratory bowl controller does not require PLC control. Process: Fasteners are filled into the bowl in bulk and conveyed upward by mechanical vibration (micro-throw principle). The vibratory bowl is automatically switched on or off depending on the fill level of the screw magazine. The screw is then conveyed by compressed air through a plastic hose to the downstream device. The feed impulse for each individual screw is triggered externally by the downstream device.

Condition: excellent (used), functionality: fully functional, Odenberg / Tomra Potato Sorting Line Optical sorter manufacturer: Odenberg Control system: Tomra (touch panel) Total operational area: 10,500 × 4,750 mm The line includes: - Odenberg optical sorter with a mechanical finger ejection system - Tomra touch control panel - Steel hopper with side/top infeed Dwsdpoykmf Hjfx Aptjb - Inclined feeding belt conveyor - Elevated feed conveyor - 2 underwater conveyor belts - Cross infeed section with vibrating screen - Discharge belt conveyors - Operator platforms with slatted flooring A complete potato sorting line designed for industrial sorting of raw material using optical technology. The Odenberg sorter, combined with the Tomra control system, enables precise product selection based on quality, color and potential defects. The mechanical finger ejection system ensures efficient and rapid separation of unwanted elements from the main product. The line is equipped with a complete system for feeding, conveying, and discharging potatoes, including underwater conveyor belts and a vibrating screen section for initial separation.

Year of construction: 2025, condition: new, 1) Conveyor belt with hopper: 1 unit Conveyor length: 8000 mm, working width: 600 mm, Hopper: length 3000 mm, width 2000 mm, height 1500 mm from the ground, EP 400/3 rubber belt with chevron pattern, 16 mm cleats, Transfer speed regulated by an inverter, max. 0.2 m/s, conveyor belt with STOP safety switch. 2) Sorting conveyor: 1 unit. Conveyor length: 10000 mm, conveyor working width: 950 mm, height: 1400 mm to the top of the belt. Height: 1500 mm to the top of the sides. The conveyor sides are made of galvanized steel, the EP 400/3 rubber belt is smooth, and the conveyor sides are 100 mm. A hopper with a height of 600 mm on both sides and a width of 1000 mm. The conveyor speed is regulated by an inverter with a maximum speed of 0.3 m/s. 3) Work platform: 6 units, platform width: 1200 mm, platform length: 1200 mm, platform height: 500 mm, platform with safety barriers. 4) Loading grippers for recyclable materials: 8 units, Height: 1300 mm, width: 1300 mm, length: 1300 mm, Dsdped N Hhuofx Aptewb With pivoting wheels and handles for attaching big bags. 5) Ballasted conveyor belt on a rotating axle and two running wheels: 1 unit, Conveyor length: 8000 mm, working width: 600 mm, Hopper: length 1200 mm, width 1000 mm, height 1000 mm above the ground, Ascent height: 3700 mm, EP 400/3 rubber belt with 60 mm T-cleats, 500 mm, fixed speed 0.4 m/s, conveyor belt with STOP safety switch. 6) Sorting line, equipped with an electrical distribution box, safety stop switches, and a 32A / 5 and 15m long connector of the power cable with rubber insulation. 7) The system has a 12-month warranty. 8) The system has a CE certificate. The pictures show the setup of such a sorting system. We produce versions with 4, 6, 8, 10, or even 12 workstations. Semi-mobile or stationary. Mounting on the floor or on a frame. Price - ex works Poznań (Poland). We have many references in the European Union. We speak Polish, German, English, and Russian.

Condition: used, Year of construction: 2022, functionality: fully functional, machine/vehicle number: MJY 142S-35, MJF 143-1535, MJY-MJF production line from the Chinese manufacturer China SHENGONG. The equipment was commissioned in 11/2022 and is designed for processing round logs with a maximum diameter of 340 mm and length of 5 m. The technology comprises: - Log infeed deck for 5 m logs with dosing and centering - Infeed conveyor to the machine - Double-shaft canting saw MJY 142S-35 - Outfeed pressure rollers - Distribution outfeed conveyor for cant and side boards - Side boards conveyor - Cant conveyor with lateral ejection and flipping - Cant conveyor to multi-rip saw - Centering unit before multi-rip saw - Double-shaft multi-rip saw MJF 143-1535 - Lumber conveyor behind the saw - Side chains and lumber conveyor - Edging saw MJ 141-0440 with 5 lasers for saw blade positioning - Roller conveyor before and after the edger - Belt conveyor under the Multipris for offcut removal - Connecting belt conveyor - Belt conveyor under the multi-rip saw for offcut removal to chipping Dwsdsw Rg Emepfx Aptsb - Belt conveyor for removal from the hall - Chutes and conveyor connections - Accessories: hydraulics, electrics, and control system The price of the technology is without dismantling and at FCA Nepomuk Incoterms.

Condition: used, Year of construction: 2000, functionality: fully functional, Holtec sorting block train, type SBZ. Length 94.5 m. 52 boxes. Djdpfx Aow Ug Agoptjwb

Year of construction: 2005, condition: used, functionality: fully functional, NIR device Polysort 2000 from Tomra with a complete sorting line consisting of feed chute, acceleration belt, separator edge and canopy, optionally with additional conveyor belts. Dwedpfx Aeylzqgoptsb

Year of construction: 2015, condition: excellent (used), Manufacturer: S+S Separation and Sorting Technology GmbH Type: Unicon-D 2000/400/450/100 Dwsdpfx Aok Eakveptjb Year: 2015 Electrical data: -230 V -0,7 A -50 Hz -IP 65

Condition: excellent (used), Year of construction: 2015, Manufacturer: S+S Separation and Sorting Technology GmbH Type: Unicon-D 2000/400/450/100 Year: 2015 Electrical data: - 230 V - 0,7A Dwsdpfx Aelatz Dopteb - 50 Hz - IP 65 Inclusion dimensions: 2060 x 650 x 1260 mm Belt width: 390 mm Belt length: 2000 mm

Condition: new, Year of construction: 2026, operating hours: 1 h, functionality: fully functional, machine/vehicle number: 2026, Optical precision drill grinding High-precision and very easy-drill grinding with optics and , Costsaver and Swiss in 100% quality. grind drills, thinning and check in the shortest time and with maximum precision. With MEGA POINT blue line you win more than once, achieve with it: - Better positioning - Improved accuracy of diameter - Significantly longer service life - Feed force is greatly reduced The MEGA POINT blue line is a versatile precision drill grinding machine, which is easy and ergonomic operation and a variety of drills handelsueblichen nachschleift perfect and optimized. MEGA POINT blue-line 1-20mm (Optiom to 30mm) Technical specifications: Our MEGA POINT drill grinding allows precise and rapid regrinding and thinning all handelsueblichen drills. Our customers have so always perfectly ground drills for disposal. The sophisticated design provides enormous flexibility in terms of the different cut angles and the thinning of the drill. Without a doubt, the world's best conventional drill grinding! Technical specifications Drill material grinding HSS and carbide HSCO Point angle adjustable 80 ° - 150 ° optional tip angle adjustable up to 180 ° Chuck with collets for drill diameters from 1 to 6.5 mm Chuck with collets for drill diameter 7 - 20 mm optional Spannzangenset for drill diameter 20 - 30 mm Average / free angle adjustable 0 - 40 ° Ausspitzvorrichtung, Ausspitztiefe adjustable CBN grinding wheel double-fine / coarse D 125 mm optional DIAMOND grinding wheel (for carbide drills) D 125 mm Dwsdpfxs R R R Ss Apteb CBN grinding wheel for thinning D 50 mm x 4 mm Engine power 0.3 kW Spindle speed 2800 r / min Power supply 230 volt 50 Hz Dimensions (L x W x H) 50 x 50 x 50 cm Weight about 42 kg Standardausfuehrung For right- and left-cutting, two- and dreilippige drills. With built-in optics (10x Zoom) separate Ausspitzvorrichtung and: 1 Machine light 2 chucks with collets D 1 -6.5 mm and D 7 - 20 mm 1 CBNDoppel grinding wheel D 125 mm fine / coarse 1 CBNSchleifscheibe D 50 x 4 mm 1 Set of service tools 1 instruction manual with spare parts list 1 CD-ROM with manual (CE Declaration) Danger: OPTIMA / TATAR Parts BERGER technology will take over on January 1, 2016, the stock of spare parts of HighTech OPTIMA AG. We can now offer genuine spare parts and service for the OPTIMA and TARTAR Boherschleifmaschinen.

Condition: new, Year of construction: 2026, operating hours: 1 h, functionality: fully functional, Standard equipment red line Optical precisions drill point grinding machine for 2 fluted drills regrinding and point splitting in one chucking Dwjdpfebrpr Ujx Aptsb diameter range 2 to 16 mm (1 to 20 mm as option) point angle 80° - 150° infinitely adjustable cutting angle 0° - 20° infinitely adjustable relief angle set to 30° incl. complete electrical instalation with single phase electrical motor 0,3KW 115V 60Hz (or 220V 50Hz) and integrated power-supply for illumination of the optical system incl. built-in optical projection system with 10 power lens (zoom lens with 6 - 20 power as option) incl. integrated point splitting device incl. one precision collet holder and one set of double-tapered precision-collets of your choice (MP 16 for drill-dia. 3-16 mm, MP 6,5 for drill-dia. 1-6.5 mm or MP 20 for drill-dia. 6.5-20 mm) incl. 1 double sided grinding wheel dia. 125mm CBN (one side coarse [grit ~100] second side medium [grit ~200]) incl. wheel guard with connection system for vacum cleaner incl. 1 each of detailed operating manual with pictures, spare parts list, CD-Rom and CE-Declaration (on demand)

Year of construction: 2012, condition: excellent (used), Manufacturer: Hermann Ultraschall (Herrmann Ultrasonics) Type of equipment: Ultrasonic welding system Model: VE 20 Slim Line Dialog 2400 Dwjdpsznvd Eefx Aptsb Number of welding units: 2 Serial numbers: SM 10.916/12 and SM 10.917/12 Year of manufacture: 2012 Generator power: 2400 W Operating frequency: 20 kHz Welding force (at a pressure of 8 bar): minimum: 30 N maximum: 2490 N Working stroke: 150 mm

Condition: used, Year of construction: 1999, Overview  This complete hot-fill and cold-fill bottling line was manufactured in 1999 – 2017 by Germany KHS and Krones. The line is designed for beverage production in glass and PET bottles, supporting both hot-fill and cold-fill applications. It was in operation until the end of 2025, is still installed, and is available immediately. The line can be inspected on request. Technical data  - Capacity: 12,000 – 36,000 bottles/hour (example: approx. 33,000 bph @ 500 ml) - Formats: 250 ml – 1000 ml - Application: Hot-fill and cold-fill beverage production - Container types: Glass bottles and PET bottles (hot-fill) - Filling temperature: 10°C – 104°C - CO₂ capability: Yes - Closures: - Glass: 28 mm aluminium, 33 mm / 43 mm aluminium twist-off - PET: 38 mm 3-start hot-fill closure - Labelling: Cold glue paper labels (optional sleeve labelling available) - Packaging: Wrap-around cartons and tray packaging (no shrink wrapper included) Scope of Delivery  - Depalletizer | Meypack | DL 71 | - | Low-level depalletizer with pallet conveyor and magazine - Bottle rinser | Niko | Linear Rinser | 1999 | Siemens S7 PLC, heat recovery system Dwjdpoyx I Awjfx Apteb - Filler | KHS | Innofill DNR 80 | 1999 | 80 valves, 15-head aluminium screw capper, HMI renewed 2015 - Twist-off capper | Italmeccanica / Crown | S4BLH | - | Steam-heated, automatic cap feeding - Cooling tunnel | Tuchenhagen / Göbel | K1-135 | - | 7 cooling zones - Bottle dryer | Europool | - | 2007 | High-speed air dryer - Labelling machine | Krones | Starmatic | - | Cold glue labelling, Siemens S5 - Wrap-around packer | Kisters | 320/50 | 1999 | Tray and carton packaging, Nordson hot melt - Conveyors | KHS / Krones | - | - | Complete conveying system - Palletizer | KHS | LORD 1BSN2 | 1999 | Pre-grouping, pallet formats Düsseldorf/Euro/Industrial - Pallet labeller | Logopack | - | - | Pallet labelling system - Reverse osmosis system | MWT | - | - | Capacity 800 l/h

Year of construction: 2020, condition: used, functionality: limited functionality, We offer this technological line for pellet production from vegetable waste (sunflower husk) – BART-M SRL OGM 1.5, manufactured in 2020, in used condition. Manufacturer: BART-M SRL Model: OGM 1.5 Year of manufacture: 2020 Condition: used Category: 34 Productivity: 800 kg/hour Weight kg: 6800 Dimensions mm Length: 5385 Width: 4400 Height (without exhaust pipes): 6935 Traction: electric Energy performance Total installed power kw: 150 Type of current: Alternating Current frequency hz: 50 Network voltage V: 220/380 Agrotechnical performance: Dsdpfx Apjztaahjtowb Admissible amount of non-granulated raw material: 2% max Admissible moisture content of cooled granules: 12% max Technical characteristics of the finished product: Caloric value of the granules Mj/Kg: 14-19 (vegetable waste) Kw/kg: 3.89-5.27 Diameter mm: 6-8 Length mm: 40 If you have any further questions or need more information, please do not hesitate to send us a message or call us.

Condition: used, Vibratory bowl feeder / Sorting unit / Bowl feeder / Vibratory feeder RNA Vibrating bowl, sorting unit / Screw feeding with vibratory feeder for screwdriving technology Feeding system, feeder unit Manufacturer: RNA Rhein-Nadel Automation GmbH Type: SRC-N 250-2L Serial no.: Year of manufacture: approx. 2000 Bowl diameter bottom: 300 mm Bowl diameter top: 350 mm Bowl inner height: approx. 25 mm Sorting track width: approx. 30 mm Overall height (drive + bowl with sorting track): 380 mm Vibration frequency: 100 Hz / 6000 rpm Mains connection: 230 Volt, 50 Hz - The feeder was used for supplying automotive blade fuses Space requirements: Ø x H: 420 x 390 mm Weight of bowl feeder: 52 kg Linear feeder / Vibratory feeder / Sorting unit Manufacturer: RNA Rhein-Nadel Automation GmbH Type: SLL 400-400 Serial no. 00835 Year of manufacture: approx. 2000 Maximum rail length: 700 mm Useful load: approx. 1.5 to 2 kg Vibration frequency: 100 Hz / 6000 rpm Mains connection: 220 Volt, 50 Hz - Oscillating plate L x W x H 400 x 65 x 12 mm - Mounted track length 530 mm - Overall height with oscillating plate 145 mm Space requirements: L x W x H: 580 x 120 x 400 mm Weight of linear feeder: 20 kg Control unit for vibration drives, control device, regulator, controller for vibratory feeders / sorting unit / bowl feeder / vibrating bowl / vibratory conveyor Manufacturer: RNA Rhein-Nadel Automation GmbH Type: ESK-N80 / ESG 90 Mains connection: 0 ... 208 V eff (230VAC motor operation) at 230V mains 0 ... 98 V eff (115VAC motor operation) at 115V mains Output voltage: 0...208 V (eff.) adjustable, (230 V mains) Number of power outputs: 2 Output 1: Bowl feeder, linear feeder max. 10A adjustable Output 2: Bowl feeder, linear feeder max. 6A adjustable Total load current: 16 A eff Sensor inputs: 1 Number of enable inputs: 1 (24V DC) Sensor supply: 24V DC, max. 60 mA Sensor delay ON: 0 ... 8 sec. Sensor delay OFF: 0 ... 8 sec. Power output connection: Hirschmann 7-pin Dodpfx Apsuzn Nnotswb - Two power outputs - Sensor amplifier with independently adjustable time stages (on/off) - Soft start (internally adjustable) - External enable input 24VDC Space requirements: L x W x H: 260 x 190 x 140 mm Weight of controller: 3.6 kg All units tested and in good condition.

Condition: excellent (used), Automatic filling system Logdos Späth GmbH Type K-DOS.F/AL 40/EX for filling liquids into buckets, jerricans, IBCs and drums Dodpoiyytqsfx Aptewb ATEX-protected mobile, can be moved on rollers compact dimensions: 3m x 2m x 2m (L x W x H) Programmable X/Y axis and palletizing Very good condition, directly from production!!!

Condition: excellent (used), Year of construction: 2010, Automatic technological line for sawing wood Technical data: - Max wood diameter 400 mm - Minimum wood diameter 120 mm - minimum timber length 1500 mm - Max log length 3200 mm CAPACITY UP TO 200 m3 per shift The machine consists of the following elements: - Log loader - Sawmill longitudinal feeder Dwjdpfxslar Rie Apteb - Sawmill TT 5/600/400 G - Motors 75 + 90 kW - Receiving roller table with ejecting mechanism for edgings and side boards - Driven roller table - Base table SB 4000 - Multi-saw WP 210 - 2 x 75kW engines - Receiving table - Lower return conveyor of edgings, waste to the chipper The machine is in good condition, in continuous operation - the possibility of viewing during operation

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, Technological line of the Polish brand BRODPOL for sawing medium-sized logs with a length from 1,800 to 3,000 mm and a diameter from 120 to 480 mm Year of production: 2023 Technical condition: very good The line consists of the following machines and devices: 1. Log magazine/feed conveyor with inclined discharge, type PKS 2200/2912 Year of production: 2023 2. Driven prism-shaped accelerating table, length 5,000 mm, equipped with a pneumatic log discharge mechanism Year of production: 2023 3. Driven prism-shaped accelerating table, length 4,000 mm, equipped with a log turning mechanism Year of production: 2023 4. Chain-fed circular saw unit TT5/700/480 G Year of production: 2023 5. Receiving roller table with separating plates, “bag” type, length 7,000 mm Year of production: 2023 6. Centring table SC 8000, equipped with a mechanism for stopping one cant Year of production: 2023 7. Double-spindle multi-rip saw WP 220 Year of production: 2023 8. Central belt conveyor, length 38,000 mm, belt width 500 m Year of production: 2023 Additionally, the line includes a waste receiving system with an MDR metal detector and a MADREW RK 650x200 chipper from 2021, as well as a dust extraction installation with a JKF cyclone dedicated to this line. Assembly and start-up of the line are available for an additional fee Djdjziqnuspfx Aptjwb

Condition: used, Linear feeder / Vibratory feeder / Sorting device Vibratory linear feeder, vibratory hopper, dosing hopper, storage hopper Vibratory bowl feeder, bowl feeder Vibratory bowl, screw feeding system with vibratory feeder for screwdriving technology Feeding system, feed unit Manufacturer: RNA Rhein-Nadel Automation GmbH Year of manufacture: approx. 2000 Dwsdsxf Urvepfx Aptsb Useful load: approx. 1.5 kg Oscillation frequency: 100 Hz / 6000 rpm Mains connection: 220 Volt, 50 Hz - Oscillating plate L x W = 170 x 60 x 12 mm - Mounted track length 340 mm - Overall height with base plate and oscillating plate approx. 115 mm Required space L x W x H: 400 x 280 x 400 mm Weight: 9 kg Good condition

Condition: good (used), Year of construction: 2021, Offered Equipment • Manufacturer / Model: AV Flexologic COSMOLINE 900 • Year of manufacture: 2021 • Serial no.: 051121-1059 • Condition: Excellent – the machine was in active use up to the company closure and can still be inspected under power. Why choose the COSMOLINE 900? The COSMOLINE 900 is an inline washout and drying system for photopolymer plates. It is engineered to simplify and accelerate plate processing while delivering consistent, high-quality results. ✅ Fully automated inline operation – the operator loads a plate, and the machine automatically transports, washes, and dries it. ✅ Superior cleaning – robust water jet with soap mixture, multiple adjustable rotating brushes, plus a large counter-rotating brush for maximum cleaning coverage. ✅ Reliable finishing – an additional brush for removing residues; hot air drying leaves plates clean and ready for immediate use. ✅ High productivity – sensors measure plate dimensions for optimized processing, ensuring stable and repeatable results. ✅ Environmentally friendly – standard centrifugal cleaning system; optional membrane filter available to separate polymer from water. ✅ Flexible & customizable – machine settings can be adapted to individual production requirements. This system is ideal for label and packaging converters seeking dependable, spotless, and perfectly finished flexographic plates with minimal operator effort. Technical Specifications Dedpew Tc Upofx Aptswb • Maximum plate width: 900 mm • Maximum plate height: 1,200 mm • Standard centrifugal cleaning system (sustainable solution) • Optional membrane filter for polymer recovery (not required for letterpress plates)

Condition: used, functionality: unexamined, Ultrasonic welding system, Ecoline 20L model Dwodpfx Apjzlchljteb - Ultrasonic generator K5 2000W/20kHz - Shipping available for an additional charge.

Condition: new, functionality: fully functional, Year of construction: 2025, Aggregate and ballast crusher equipment are used in the crushing and processing of various materials for construction and infrastructure projects. These crushers are designed to break down large rocks, gravel, or stones into smaller pieces, producing aggregates and ballast that are essential components in the construction industry. Here are some key aspects related to aggregate and ballast crusher equipment: 1. Jaw Crusher: - Jaw crushers are commonly used for primary crushing in aggregate and ballast production. They operate by compressing the material between a stationary and a movable jaw. 2. Impact Crusher: - Impact crushers are suitable for shaping and producing fine aggregates. They use impact force to crush the material, making them suitable for various types of rock and ore. 3. Cone Crusher: - Cone crushers are often used for secondary and tertiary crushing in aggregate production. They are efficient for producing well-shaped and finely graded aggregates. 4. Vertical Shaft Impact (VSI) Crusher: - VSI crushers are designed for shaping and producing high-quality artificial sand. They use the "rock-on-rock" crushing principle, where rocks are fed into the rotor to be accelerated and crushed against the stationary anvils. Dwodpfx Ajq Nxrxjptob 5. Gyratory Crusher: - Gyratory crushers are primarily used in mining, but they may also be used in the production of aggregates. They have a conical head and a concave surface, which crushes the material between the head and concave. 6. Mobile Crushers: - Mobile crushers, including mobile jaw crushers and mobile impact crushers, provide flexibility and mobility for on-site crushing of aggregates and ballast. They are often used in construction projects where materials need to be processed directly at the job site. 7. Screens and Scalpers: - Screens and scalpers are used to separate different sizes of aggregates after the initial crushing stage. Vibrating screens are commonly employed to classify and separate materials based on size. 8. Conveyors: - Conveyors are crucial for transporting materials between various stages of the crushing process and for stockpiling the final products. They enhance efficiency in material handling. 9. Dust Suppression Systems: - Crushing operations can generate dust, and dust suppression systems are used to minimize environmental and health impacts. These systems may include water sprays or chemical suppressants. 10. Quality Control: - Quality control measures, such as particle size analysis and gradation testing, are essential to ensure that the produced aggregates and ballast meet the required specifications and standards. 11. Environmental Considerations: - Crusher equipment should adhere to environmental regulations, and measures like dust control, noise reduction, and proper waste disposal should be implemented. When selecting aggregate and ballast crusher equipment, factors such as the type of material, required product size, production capacity, and mobility requirements should be taken into consideration. Additionally, adherence to safety and environmental standards is crucial in the operation of crushing equipment.

Condition: new, functionality: fully functional, Year of construction: 2026, A stone crushing plant for sand and aggregate making is a facility where stones and rocks are crushed into smaller pieces or gravel. It typically includes several stages of crushing and screening to produce various sizes and grades of sand and aggregate materials, which are essential in construction, landscaping, and other applications. Here's an introduction to the components and processes involved in a typical stone crushing plant: ### Components of a Stone Crushing Plant Dwjdpfx Apeq N U Dujtsb 1. Primary Crusher: - Purpose: The primary crusher, often a jaw crusher or gyratory crusher, initially breaks down large rocks into smaller pieces. - Function: It handles raw materials from the quarry or mine and prepares them for further processing. 2. Secondary Crusher: - Purpose: A secondary crusher, such as a cone crusher or impact crusher, further reduces the size of the crushed stones. - Function: It refines the material after primary crushing, producing smaller and more uniform-sized aggregates. 3. Tertiary Crusher (Optional): - Purpose: In some configurations, a tertiary crusher like a vertical shaft impactor (VSI) may be used for shaping and fine crushing. - Function: It produces finely crushed materials for specific applications, such as concrete production or road base. 4. Screening Equipment: - Purpose: Screening equipment like vibrating screens or trommel screens separates the crushed materials into different sizes. - Function: It classifies the aggregates into various grades according to size, ensuring uniformity and meeting specifications. 5. Conveyor Systems: - Purpose: Conveyor belts transport materials between different stages of crushing and screening. - Function: They ensure efficient material handling and continuous operation within the plant. 6. Washing Equipment (Optional): - Purpose: Washing equipment, such as sand washers or scrubbers, may be used to remove impurities from sand and aggregate products. - Function: It improves the quality of the final products by cleaning them and removing fines or contaminants. ### Processes Involved - Primary Crushing: Large rocks are fed into the primary crusher and reduced to a manageable size. - Secondary Crushing: The crushed materials from the primary crusher are further processed by secondary crushers to achieve the desired aggregate sizes. - Screening: The crushed and sized materials are screened to separate them into different sizes and grades. - Material Handling: Conveyor systems transport materials between different stages of the crushing and screening process. Final Product Handling:Finished products, such as sand and various sizes of aggregates, are stored or loaded for transport to customers or construction sites. Applications - Construction: Used in the production of concrete, asphalt, and road base materials. - Landscaping: Provides decorative and functional aggregates for gardens, pathways, and driveways. infrastructure: Essential for building foundations, drainage systems, and structural fill. As for the capacity we have 30 t/h, 30-50 t/h, 50-100 t/h, 100-150 t/h, 150-200 t/h, 200-300 t/h, 300-500 t/h, and both stationary crushing plant and mobile crushing plant are available for option.

Condition: new, functionality: fully functional, power: 460 kW (625.43 HP), fuel type: electric, Year of construction: 2026, Henan Mingyuan Heavy Industrial Equipment Co., Ltd. has established itself as a premier global manufacturer, providing integrated Sand and Gravel Production Lines that transform raw minerals into precision-graded materials. A MINGYUAN production line is not just a collection of machines; it is a synchronized system engineered for maximum throughput, minimal waste, and low operational costs. -1. Core Equipment Configuration The MINGYUAN system follows a multi-stage reduction philosophy to ensure particle shape and quality. Vibrating Feeder (GZQ Series):Ensures a continuous, uniform flow of raw material to the primary crusher. It features grizzly bars to pre-screen dirt and "fines," protecting the crusher from unnecessary wear. Primary Jaw Crusher (PE/C-Type): The "workhorse" designed for the initial breakdown of hard rocks (granite, basalt, river pebbles). MINGYUAN’s jaw crushers utilize a deep-chamber design for high crushing ratios. Secondary Crusher (Impact or Cone):Impact Crusher (PF Series): Ideal for medium-hard materials; produces highly cubic final products with excellent grain shape. Cone Crusher (Hydraulic/Spring): Preferred for high-hardness materials (granite/quartz) due to its high efficiency and low wear-part consumption. Sand Making Machine (VSI Series): The "finisher." It uses "stone-on-stone" or "stone-on-iron" technology to shape aggregates and produce high-fineness artificial sand. Vibrating Screen (YK Series): A high-frequency circular screen that classifies material into specific sizes (e.g., 0-5mm, 5-10mm, 10-20mm, 20-40mm). * Sand Washing Machine (XSD/LSX Series):Removes mud and impurities to ensure the final product meets strict concrete and asphalt standards. Dwsdpfx Asq Nywxsptsb 2. Technical Specifications & Performance MINGYUAN offers scalable solutions tailored to project size, ranging from small-scale mobile units to massive industrial stationary plants. | Feature | MINGYUAN Standard Specifications | | Production Capacity | 50 – 600 $t/h$ (Tons Per Hour) | | Max Input Size | Up to 1,100mm (depending on Jaw model) | | Finished Product Size | 0-5mm, 5-10mm, 10-20mm, 20-40mm (customizable) | | Power System | High-efficiency AC Motors or Diesel-Electric Hybrid | | Control System| Centralized PLC Control Cabinet with safety interlocks | | Materials Processed | River stone, granite, limestone, basalt, iron ore, and C&D waste | 3. The MINGYUAN Technical Advantage What differentiates MINGYUAN in the global market is the "One-Stop" solution approach: 1. High Crushing Efficiency:Optimized crushing cavities increase the contact area between the material and the liners, reducing energy consumption per ton. 2. Environmental Compliance: Systems can be equipped with advanced dust suppression misting and fully enclosed belt conveyors to meet stringent urban environmental regulations. 3. Durability: Wear parts (jaw plates, blow bars, mantles) are manufactured using high-manganese and high-chrome alloys, significantly extending the time between maintenance cycles. 4. Flexible Layouts: Whether for a mountain quarry or a tight urban recycling site, MINGYUAN provides customized CAD layouts to optimize gravity-flow and reduce conveyor length. 4. Conclusion A MINGYUAN Sand and Gravel Production Line represents a strategic investment in efficiency. By combining primary strength with precision finishing and washing, the brand ensures that every ton of raw material is maximized for its commercial value.

Condition: used, Year of construction: 2006, functionality: fully functional, Complete briquetting line 2 x RUF 330. Boiler room, drum dryer, conveyors. Dwjdpfxexazhto Aptob