Used Mikron Multistar for sale (174)

Condition: ready for operation (used), Year of construction: 1998, A Mikron CNC vertical machining center is available. Travel X/Y/Z: 900mm/630mm/500mm, table dimensions X/Y: 1200mm/600mm, max. table load: approx. 500kg, tool holder: SK40, speed: 5000rpm, rapid traverse: 10m/min, feed: 10m/min. Machine dimensions X/Y/Z: approx. 2400mm/3400mm/2300mm, weight: approx. 5000kg, control: Mikron, operating hours: approx. 35580h. The main control board of the machine has a defect. Including approx. 100 SK40 tool holders and tools. An on-site inspection is possible. Iodpfx Ajzf Ncieiyoig

Condition: used, condition Defekt/Ersatzteilträger manufacture Mikron Iijdpfx Aisyzt A Uoyeg type HSM 400 U The machine is defective and is being sold for spare parts. Accessories, tools, and clamping devices shown are only included if explicitly stated in the additional information. Technical data and specifications are subject to change without notice. Prior sale is reserved.

Condition: used, Year of construction: 1982, x-travel 400 mm y-travel 400 mm z-travel 380 mm Iijdju U Sabopfx Aiyog total power requirement 2,6 kW weight of the machine ca. 1,5t t

Condition: used, Year of construction: 1992, max. wheel diameter 150 mm Iodpfx Aijt Hwxboyeig gear width 300 mm max. module 4,5 min. module total power requirement 20 kW weight of the machine ca. 6 t dimensions of the machine ca. m

Condition: used, Year of construction: 1985, max. wheel diameter 80 mm gear width 150 mm max. module 2,5 min. module total power requirement 10 kW weight of the machine ca. 2400 kg Ijdpfjt Hw D Rsx Aiyeig M I K R O N (Switzerland) Fully Automatic Gear Hobber for Worm Gears Model A 33 / 1 Year 1985 Ser.-No. 14.06/14.07/14.15 _____ max. gear- without feed magazine approx. 80 mm max. gear- with feed magazine approx. 50 mm Module max. 2, / 2,5 Axial milling length approx. 150 mm max. workpiece-mounting length approx. 200 mm Milling slide can be swivelled up to 90 degrees Milling cutter - 24 - 50/63 mm Max. radial distance of milling slide 0-14/18 mm Milling cutter adjustment max. 25 mm Milling cutter speed 212 - 2.000 rpm Axial feed range infinitely adjustable 0,05 - 4,0 mm/workpiece rotation radial infinitely adjustable 0,2 - 200 mm/min. Milling spindle drive 3 kW Total electrical load approx. 10 kW - 50 Hz - 380 Volt Weight approx. 2.400 kg Accessories/Special Features: " Fully automatic operation cycle and minimum idle times due to programmable SIEMENS Program Controls S 5 for all machining steps i.e. rapid gear, feed, milling cutter on/off for the loading device, tailstock, possibly shifting, etc. with unit counter, program numbering including 30 different numeric error displays Pneumatic workpiece-loading and unloading facility parallel to work piece axis upright for rod workpieces approx. 140 mm long x 8 mm , including pneumatic double gripper for loading and unloading of work pieces. Raw parts are inserted into change cassettes externally and then placed into the loading device. The double gripper places the parts between workpiece spindle and tailstock, the tailstock spindle sleeve pushes the parts in the main spindle collet and clamps them simultaneously. The finished parts are ejected from the main spindle, then placed back again into the finished parts cassette by the gripper. The whole process is electrically monitored and checked. The complete loading facility is encased by plexiglass. " Hydraulic work piece clamping device including collets and hydraulic ejector " separate cooling system with magnetic separator * separate hydraulic system * various change gears This machine is set up for worm gears/armature shafts that can be used for adjustable car seats, window lifters, etc.

Condition: used, EQUIPMENT - With automaton Zellio SR3 type Iiodeuhbqpjpfx Aiyeg - Tilting loader no. 11 and vibratory bowl - part diameter 2.50 to 12.5 [mm] - part length 0.30 to 30 [mm]

Condition: used, TECHNICAL DETAILS - table dimensions : 350 x 800 [mm] - T-slots : 7 - strokes, x, y, z : 400, 400, 370 [mm] - spindle speed : 50 - 2240 [rpm] - feed speed of potentiometer : 0 - 630 [mm/min.] Iijdpfx Aouhbxajiysg EQUIPMENT - 3 axis display HENDENHAIN - steel sheet retention

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, travel distance X-axis: 1,000 mm, travel distance Y-axis: 750 mm, travel distance Z-axis: 750 mm, controller model: Heidenhain TNC426, rotational speed (max.): 12,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range, X-axis: 1,000 mm Travel range, Y-axis: 750 mm Travel range, Z-axis: 750 mm Table size: 1,150 x 700 mm Tool shank: SK40 Spindle speed range: 12,000 rpm MACHINE DETAILS Control system: Heidenhain TNC426 Machine weight approx.: 10,500 kg Iedpfxezi D Rcj Aiysig EQUIPMENT 30-position tool changer Electronic handwheel Chip conveyor Coolant system

Year of construction: 1990, condition: excellent (used), Mikron WF2S tool milling machine with a 3-axis Elesta-Visulesta digital display. Fixed angular table, SK 40 spindle mount. In very good, operational condition, from an institute. The machine can be demonstrated under power by arrangement. Iisdpfjg Nw Rzsx Aiyog

Condition: excellent (used), Year of construction: 2015, Mikron HPM 800U HD 5 axis Vertical Machining Centre, with 7 pallet changer (2015) Traverses XYZ: 800 x 800 x 550mm, 500 x 500mm table, A axis -91 / + 121 degrees, Iijdpfszm Ticex Aiysg C axis, 360 degrees, Heidenhain TNC530, Spindle Speed 20,000rpm, 36kW Spindle Motor, HSK A63 Spindle Taper, 165 tools, swarf conveyor, through spindle coolant,

Condition: good (used), Year of construction: 2006, travel distance X-axis: 800 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 500 mm, feed rate X-axis: 30,000 m/min, feed rate Y-axis: 30,000 m/min, feed rate Z-axis: 30,000 m/min, controller manufacturer: HeidenHain iTNC530, total height: 3,200 mm, total length: 3,200 mm, total width: 2,400 mm, table width: 600 mm, table length: 600 mm, table load: 500 kg, overall weight: 10,000 kg, spindle speed (max.): 20,000 rpm, spindle motor power: 18,000 W, 5-axis CNC machine (VMC) MIKRON - UCP 800 MACH-ID 9640 Make: MIKRON Type: UCP 800 Control: HeidenHain iTNC530 X - Travel: 800mm Y - Travel: 650mm Z - Travel: 500mm A - Axis: +120 to -100° B - Axis: 360.000° Table Length: 600mm Table Width: 600mm Table load: 500 Feed rate X-Axis: 30000mm/min. Feed rate Y-Axis: 30000mm/min. Feed rate Z-Axis: 30000mm/min. Spindle Taper: HSK63ISO/Bt/Mk Power on spindle: 18kW Speeds / ranges: 20000Rpm ATC / revolver: 30 Coolant through spindle / Bar:20 Number of controlled axis: 5 Chip conveyor: yes Coolantsystem: yes Length: 3200mm Width: 2400mm Height: 3200mm Iiodpfszkry Iox Aiysg Weight: 10000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, functionality: fully functional, Year of construction: 2025, machine/vehicle number: MHG5202500000125, Orange Peel Grapple for Scrap Capacity 600 Liters Ijdpfx Aiexrymxeyeig Model 5 Tinned Gross Weight 1150 KG

Condition: new, functionality: fully functional, Year of construction: 2025, machine/vehicle number: MHB5202500000156, Scrap Grab for Terex Fuchs, Sennebogen, Liebherr 5 Tinned Model Iijdpsxryn Aefx Aiyjg 500 Liters Capacity

Condition: new, Year of construction: 2025, Scrap Grapple, Scrap Grab, Multi Tine Grab for Scrap Capacity 0.6 m3 Model 5 Tinned Iedpfxexryrbj Aiyoig Hardox 450 Wearing Plates Rotating Option

Year of construction: 2023, condition: new, Polyp Scrap Grapple for Cranes Palfinger Hiab Iedpfjnzibljx Aiyeig Capacity: 300 Lt / 0.3 m3 Model: 4 Tinned - Half Closed Gross Weight: 450 Kg

Condition: good (used), Year of construction: 1980, Mikron WF2 milling machine with a 3-axis Heidenhain digital display. Fixed angular table, SK 40 spindle mount. In good, operational condition, from a precision engineering workshop. Machine can be demonstrated under power by arrangement. Iiodpfx Aezq R Aheiyeg

Condition: ready for operation (used), Selling a well-maintained Mikron VC 1000 milling machine due to the purchase of a new machine. Iiedpoh Tnpxsfx Aiyog

Condition: used, CNC control, control panel, machining center operator panel, control unit, control panel, control unit Iiodpeprb Dvsfx Aiysg -Manufacturer: Mikron, operating unit -Type: TCD 22 - DIN 8659 -Printed circuit board: WW TCD 22 control unit 104.73.20.042 -Individual components: see photos -Dimensions: 480/130/H240 mm -Weight: 5 kg

Condition: good (used), Permanent magnet motor, electric motor, servo motor, geared motor, three-phase motor -Manufacturer: Siemens, Permanent Magnet Motor from CNC milling machine Mikron WF 51C/155 -Type: HU3074-,0AC01-Z -Voltage: 167 V -Power: 1.8 kW -Speed: 2000 rpm -Shaft: Ø 22 x 45 mm -Number: 2x motors available -Price: per piece Iiodpfx Aiskxhpusyog -Dimensions: 390/140/H185 mm -Weight: 23 kg/pc.

Condition: used, Transformer, transformer, converter, three-phase autotransformer, three-phase transformer -Manufacturer: Bosch, three-phase transformer from CNC milling machine Mikron WF 51C/155 -Type: 100-911637 -Power: 4.5kVA -Primary: 3x380V -Secondary: 3x95/165 V Iiodpfekyy Uqsx Aiyog -Dimensions: 335/135/H350 mm -Weight: 41 kg

Condition: used, Inrush current limiter, soft starter, soft starter, starting current limiter, soft starting choke -Manufacturer: varimax, soft start choke, three-phase choke from CNC milling machine Mikron WF 51C/155 -Type: D 1515 S3 -Current: 10A -Dimension: 180/90/H190 mm Iiedekzpngjpfx Aiyeg -Weight: 9.5 kg

Condition: good (used), Servo Drive, Servo Card, Input Processor, Control Card, Input Card, Controller, Converter, Controller, Servo Module, Axis Amplifier, Axis Amplifier, Velocity Control Unit, Spindle Amplifier Module, Servo Amplifier -Manufacturer: Bosch, transistor amplifier completely equipped from CNC milling machine Mikron WF 51C/155 -Type: TR15-XA-140-230V -Control cards/single modules: see photos Iodpfxowd N S De Aiyeig -Dimensions: 480/260/H365 mm -Weight: 24 kg

Condition: good (used), Transformer, converter, three-phase autotransformer, three-phase transformer -Transformer: from CNC machining center Mikron VC500D -Type: PTNo.. PTC 2500/139 Iisdpfxsy Tv S As Aiysg -Power: 1200 VA -Dimensions: 215/210/H255 mm -Weight: 30.2 kg

Condition: good (used), PLC control, power module, LT module, E/R module, regenerative module, CNC control, safety slot universal module, plug-in cards, printed circuit boards, control card, circuit board -Manufacturer: Mattle Mikron, safety insert universal module board from CNC milling machine Mikron UME 600 Isdperb E Ewsfx Aiyjig -Safety module: Type SEMU TN 24VDC -Board: Mikron 958 74 10 275 S300 -Dimensions: 300/170/H200 mm -Weight: 1.4 kg

Condition: good (used), Safety switch, safety switch, protective grid switch -Manufacturer: Euchner, Safety switch from CNC milling machine Mikron UME 600 -Type: TZ2LEO24M ID No.: 090559 Ijdpforb E E Eex Aiyoig Technical data: see photo of the nameplate Quantity: 1 piece available -Dimensions: 170/110/40 mm -Weight: 1.1 kg