Used Separators for sale (6,016)

Condition: excellent (used), Year of construction: 2013, Technical data: ALKO clean air mobile extraction unit, Type: Mobil-Power Unit APU 120, Motor power: 1.5 kW, Suction nozzle Ø=120 mm, Soundproofed, mobile separator container 135 l, manual filter cleaning, Dimensions: L=1,085 mm, W=650 mm, H=1,985 mm, Dust container volume: 135 liters, Weight: 117 kg, Nominal air volume (after cleaning): 814 m³/h, Iiodpfjw Aprzox Aabsh Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) Iijdsw Sgnkjpfx Aabsh - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice

Condition: excellent (used), Year of construction: 2013, LAMELLAR - CASE CLAMP GANNOMAT "CONCEPT 70 ECO" Complete in standard configuration with: Case joints. - Counter-pressure surfaces (side pressure wall, base) are 40 mm thick, coated, continuous support plates - Electrically operated adjustment of both press beams via precision trapezoidal-thread spindles (with increased lead and concentricity accuracy) and high-performance running nuts with grease reservoir. - Clamping is performed electrically using two separate worm gear motors (2 x 0.75 kW) - Pressing force: 2000 daN (kg) per press beam. - The pressing force of the press beam is electronically regulated and set via frequency converter, thus torque transmission is completely wear-free. - Pressing and adjustment speed: 25 mm/sec. - Very simple operation via 6 separate push buttons; 6 movement operations can be selected via the controller. - Freely adjustable pressing time preselection with automatic opening: 0-30 min (switchable to seconds or hours). - Working height/feeding height: 300 mm - Working dimensions: Length min: 150 mm, max: 2550 mm; Height min: 150 mm, max: 1400 mm. Depth: 700 mm Iedpfxew Tdyms Aabsih 1 selector switch for variable pressing force: 1000 / 1500 / 2000 daN (kg) Machine No. 380.324 400V, 3Ph, 50Hz (2.5 kVA, 16 A) Set of machine feet for working height 500 mm Machine used: Year of construction: 2013, fully overhauled by Ganner, 6-month parts warranty Special price: ex-stock 54634 Bitburg - immediately available -

Condition: as good as new (ex-display), Year of construction: 2024, Technical data: Iiedpfeb Eln Dex Aabeh Slat carcass press from our showroom; Working range: width from 150 - 2.550mm, height from 150 - 1.400mm; depth from 150 - 700mm; Variable pressing force adjustment 300/700/1100/1400/1800/2200 dN(kg) of the lateral pressing beam; Variable pressing force adjustment 500/800/1200/1500/1900/2200 dN(kg) of the upper pressing bar Simple operation via 6 separate push buttons, Freely adjustable pressing time preselection with automatic opening, Charging height 300 mm Machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg

Condition: as good as new (ex-display), Year of construction: 2025, OPTIdrill D 26PRO - Column drilling machine Table and column drilling machine with V-belt drive User-friendly safety switch in accordance with IP 54 with undervoltage release and separate emergency stop switch 400 volt models with right/left rotation Drilling depth stop Precisely machined drilling table with diagonal T-slots Height adjustment of the drilling table via rack Drilling table can be tilted ± 45° and rotated 360° V-belt cover with safety switch Aluminum die-cast spindle lever made from one piece with soft-grip handles Industrial motor Precision spindle bore Machine operation including safety electronics in 24 V direct current Isdpfxjdqzbns Aaboih Guaranteed concentricity

Condition: new, Year of construction: 2025, Heavy machine base guarantees high torsional rigidity and vibration-free operation Better sanding results due to sanding belt oscillation via separate gear motor Oscillation optionally switchable Veneer edge sanding device with fine adjustment as standard Grooved infeed ruler for sanding veneer overhangs Quick changeover from veneer to solid wood sanding Height-adjustable sanding table for utilization of the entire sanding belt width Height adjustment of the sanding table and sanding unit swivelling via hand wheels Height-adjustable additional table with suction device for grinding radii Optimum chip removal through extraction at the unit and at the cross table Automatic compensation of strip length differences due to spring-loaded strip tension Dimensions and weights Length approx. 1900 mm width/depth approx. 810 mm Height approx. 1230 mm Weight approx. 290 kg Dust extraction connection Suction socket diameter 120 mm Drive power Oscillating motor 0,25 kW Work table(s) Working table length 960 mm Working table width 352 mm Working table height adjustment 210 mm Cross table height min. 730 mm Electrical data Input power 3 kW Supply voltage 400 V Phase(s) 3 Ph Current type AC Mains frequency 50 Hz Sanding unit Sanding belt length 3000 mm Iedpfjff Ed Tjx Aabsih Sanding belt width 150 mm Belt speed(s) 20 m/s grinding surface length 1050 mm Grinding surface width 220 mm Swivel 0 - 45 ° Oscillation stroke 20 mm Availability: Short term

Condition: new, Year of construction: 2025, Robust design also allows the machining of longer workpieces Sanding unit swivels, therefore also usable as edge sanding machine 225 mm large balanced belt rollers ensure low-vibration drive. Easy adjustment of the grinding belt High belt speed of 17 m/s Right-left rotation Upper grinding sole with graphite coating grinding shoe 4-fold spring mounted With movable grinding shoe for bevelled surfaces Smooth-running grinding table even with high loads from heavy workpieces Optimal price-performance ratio Additional equipment ESE Electrical table height adjustment as standard Divided table to fold up for special edge grinding Drawer sanding device Integrated worktable lighting Equipment details 225 mm large balanced belt rollers ensure optimum and low-vibration drive belt speed 17 m/s With swivel-mounted professional sanding shoe for bevelled surfaces 4-fold spring suspension Electrical table height adjustment as standard Operating elements ergonomically arranged on separate control panel With drawer sanding device as standard Divided table to fold up for special edge grinding applications Dimensions and weights Iiodpfxsff Hdfs Aabsh Length approx. 3750 mm width/depth approx. 1250 mm Height approx. 1730 mm Weight approx. 520 kg Dust extraction connection Suction nozzle diameter 160 / 160 mm Work table(s) Work table height adjustment 550 mm Work table transverse stroke 690 mm Electrical data Power Höh

Condition: new, Year of construction: 2024, The Uniq series is the full-fledged basis of our range and shares all the features that have helped the Kündig edge sanding machine gain its reputation on the market as a robust, versatile precision instrument. Part of its extremely solid construction is the motorized oscillating sanding unit, which offers a maximum oscillation travel of 90mm and the possibility of motorized tilting by up to 45°. All the usual edge processing operations can be carried out at the up to four grinding stations. Edge sanding machine Kündig Uniq front and rear side Ingenious design - the sanding unit The heart of all our edge sanding machines is the sanding unit. It offers a whole range of intelligent functions and features. For example, the sanding belt does not oscillate by tilting the belt rollers. Instead, the entire sanding unit moves up and down. The oscillation stroke, as well as the oscillation range, are easily set by pressing a button. Thanks to the flexible adjustment and the large oscillation travel, sanding belts can be used optimally over their entire width, without the need for laborious adjustment of the worktable height. The oscillation mechanism is driven by a separate motor. Iisdpfjfig Rwjx Aabjh The sanding unit can also be tilted conveniently by means of a rotary switch and also with the aid of a separate motor. The unit can be tilted between 90° and 45°. Thanks to the sophisticated swivel mechanism

Condition: new, Year of construction: 2025, Technical data: Suction capacity 510 l/min. Filling capacity 400 l/min. Maximum pressure 10 bar Tank capacity 90 l Cylinder/stages 2/1 Speed 1.300 min/1 Motor power 3 kW/ 400 V Description: The universal with V-belt drive and qualitative equipment especially suitable for craftsmen for use where compressed air quality, durability and efficiency are essential long life thanks to high performance low speed units safe transport and excellent stability thanks to large wheels with parking brake Optimum cooling thanks to large fan impeller aftercooler with cooling fins ensures a low boiler inlet temperature and thus less moisture in the compressed air Iiodpfshk Dfkox Aabjh better efficiency due to optimised aggregates Standard with: Condor pressure switch Pressure gauge Pressure reducer with water separator and Rectus quick coupling Motor with overload protection Location: Ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, Raw air extraction unit ASA 203 Iodpfxjhk S Szj Aabjih With standard undercarriage Dimensions and weights Chip collection volume 175 l Nominal width external suction inlet 200 mm Length approx. 1061 mm Width/depth approx. 577 mm Height approx. 2300 mm Weight approx. 60 kg Electrical data Supply voltage 400 V Mains frequency 50 Hz Filter Filter area 2.2 m² Noise emission Sound pressure level max. 84 dB(A) Volume flow Nominal volume flow 2500 m³/h For milling, planing and sawing chips (no dust) Substantially reduced dust content due to BIA-tested filter material with high separation efficiency Housing parts and impellers made of high-strength special plastic Quick release fasteners for filter and chip bags for unproblematic maintenance Robust, high-quality design Easy to move due to swivel castors Low power consumption Suction units comply with dust class L Scope of delivery: System body with mounted fan unit Filter bag / extraction unit chip bag / extraction unit without suction hose

Condition: as good as new (ex-display), Year of construction: 2025, The impressive advantages: Space-saving compact design - comfortable and powerful. Excellent surface quality and a pleasant working environment due to diagonallow-turbulence air-stroemung. Large detection window thanks to air guide plates – thus also suitable for larger factory troughs. Separation degree of paint mist up to 99%, return ability of the pre-filter up to 18 kg/m2 - thus great filter life! Easy and fast filter change on the front. Cost-cost replacement filters. Iiododqc U Hopfx Aabjh Low acquisition costs and low energy requirements. Dry spray wall made of galvanized sheet steel with welded base frame, cardboard labyrinth filter as pre-filter and glass fiber filter as post-filter unit. Ex-fan incl. throttle valve attached to the left. Do not compromise on the quality of the surface. Suction-weighing Easy Paint are the ideal cost-effective application for the effective detection and filtering of the paint mist as well as the suction of the solvent dimempfe. Robust and powerful but economical in consumption. Thanks to the IPE double filtration system, two filter levels ensure a maximum separation degree of up to 99%. Thanks to the folded filter pockets, the cardboard labyrinth filter absorbs considerably more overspray (up to 18 kg/m2 filter area) than conventional filter mats. The downstream fiber glass fiber second-based filter absorbs only the finest residual particles. As a guideline, the cardboard labyrinth

Condition: new, Year of construction: 2025, An all-round reliable, mobile family: AL-KO POWER UNIT® extraction systems are available for maximum volume flows between 790 and 10,000 m³. This makes the energy-efficient AL-KO POWER UNIT® models the perfect solution for small and medium extraction volumes or an ideal supplement to existing stationary systems. Your advantages: - IE 3 motor as standard - approx. 73 m² filter surface - Pre-separator as standard Iiedpfxjhkzt Ne Aabsh - Certified according to GS-HO-07 - H3 residual dust content 0.1 mg/m³ safely complied with (wood dust) - Optionally with type-tested rotary valve (FSA) - Tested backwater flap - Integrated automatic extinguishing system Technical data: - Nominal motor power: 11.0 kW /3 Ph - voltage: 400 V / 50 Hz - max. volume flow: up to 8,500 m³/h at the fan - nominal volume flow: 6.927 m3/h - Negative pressure at nominal V: 2,543 Pa - Intake connection: 350 mm - Noise level: 71 dB (A) at full load (according to DIN EN ISO 11201) - Chip collection volume (net/gross): 3 x 165 L / 3 x 250 - Dimensions (L x W x H) in mm: 3,130 x 1,058 x 2,361 - Net weight without packaging: 977 kg - Dust class H3 Location: ex stock 54634 Bitburg - immediately available - as in stock subject to prior sale

Condition: new, Year of construction: 2025, Compact design Highest reliability High suction power Integrated pre-separator 100 % air recirculation Residual dust content < 0.1 mg/m³ Low noise emission Longer filter life Easy emptying Iedpjhkzu Ajfx Aaboih Supplied ready to plug in With rotary valve Models with rotary valve: AL-KO POWER UNIT® 300 ZRS Intake port: 300 mm Nominal motor power: 7.5 kW / 3 Ph Voltage: 400 V / 50 Hz Maximum volume flow 4,900 m³ / h 6,000 m³ / h Nominal volume flow: 5.089 m³ / h Negative pressure: 2.280 Pa Filter area: 30 m² Filter cleaning: pneumatic Dimensions (L x W x H) in mm: 2,950 x 994 x 3,013 Cellular wheel capacity:15.816 L / h Weight:920 kg Location: ex stock 54634 Bitburg - immediately available - subject to prior sale

Condition: new, Year of construction: 2025, Raw air extraction unit ASA 163 With standard undercarriage Dimensions and weights Chip collection volume 175 l Nominal width outside suction socket inlet 160 mm Length approx. 1096 mm Width/depth approx. 648 mm Height approx. 2300 mm Weight approx. 40 kg Electrical data Supply voltage 400 V Mains frequency 50 Hz Filter Filter area 2.2 m² Noise emission Sound pressure level max. 83 dB(A) Volume flow Nominal volume flow 2200 m³/h For milling, planing and sawing chips (no dust) Substantially reduced dust content due to BIA-tested filter material with high separation efficiency Housing parts and impellers made of high-strength special plastic Iedpfx Aashk S S Esbsih Quick release fasteners for filter and chip bags for unproblematic maintenance Robust, high-quality design Easy to move due to swivel castors Low power consumption Suction units comply with dust class L Scope of delivery: System body with mounted fan unit Filter bag / extraction unit chip bag / extraction unit without suction hose

Condition: new, Year of construction: 2024, Holzkraft edge sanding machine Type: KSO 200 F with veneer sanding device Sanding unit can be swivelled up to 45° by means of a lever Machine stand made of welded steel guarantees high torsional stiffness and vibration-free operation. Oscillating sanding belt with separate gear motor for better sanding results Oscillation optionally switchable Sanding soleplate with graphite coating for a longer service life of the sanding belt Height-adjustable sanding table for utilization of the entire sanding belt width Height-adjustable additional table with suction for grinding radii Spring-loaded belt tension automatically compensates for belt length differences. With double suction Extendable roller table extension With rubberized sanding roller Veneer edge sanding device with contact shoe with fine adjustment, relief rollers and stop rulers With grooved infeed ruler for veneer overhangs Quick changeover from veneer edge sanding to solid wood sanding possible Dimensions and weights Length approx. 1900 mm Width/depth approx. 900 mm Height approx. 1350 mm Weight approx. 290 kg Connection dust extraction suction nozzle diameter 140 / 100 mm Drive power oscillation motor 0,25 kW Working table(s) working table length 960 mm working table width 350 mm Working table height adjustment 230 mm Ijdelht H Nepfx Aabjih Height min. 735 mm Height max. 965 mm Height adjustment longitudinal table 230 mm Cross table length 330 mm Cross table width 330 mm Cross table height min. 720 mm Cross table height max. 900 mm Cross table height adjustment 180 mm Electrical data Power drive motor 3,0 kW Supply voltage 400 V Grinding unit grinding belt length 3000 mm grinding belt width 200 mm Belt speed(s) 20 m/s Grinding surface length 1050 mm grinding surface width 200 mm Oscillation stroke 20 mm Location: Ex stock 54634 Bitburg - immediately available -

Condition: like new (used), Year of construction: 2025, operating hours: 1 h, Super special price, as it was on display at our in-house exhibition. Operating hours: 1 Iedpfx Ajtnz Ttjabsih Available immediately - subject to prior sale If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg

Condition: new, Year of construction: 2024, your benefits Sturdy press mechanism with low-wear, chrome-plated tongs Pressing chamber wear bush Pre-compressor with end-position-sensed cylinder and screwed cover Control box with SPS-control Screw channel with discharge screw Separate oil tank with pump motor and valve control Safety switch for oil temperature Mounting on stable base frame with rubber feet Briquette quantity monitoring Robust construction, low-maintenance technology, little space requirement: The machines of the C-series are particularly suitable for small and medium-size enterprises, whose required throughput does not exceed 50-80 kg/h or 200 to 400 kg/day. Practically any suitable material can be briquetted, e.g. wood, polystyrene, foam, paper or biomass. All machines are available as left- or right-hand version. The mounting on a stable base frame ensures a quick installation and makes mobile use possible. Briquette diameter (mm) 50 Throughput capacity up to (kg/h) 50 (depending on material) Hydraulic motor (kW) 5,5o Iiedpfx Ajcnz U Eeaboh Screw motor (kW) 0,55 Oil quantity (litres) 100 Weight (kg approx.) 800 Outstanding features at a glance Hydraulics with separate oil tank: temperature-controlled hydraulic unit, complete valve control, pump motor for long running times Briquette length monitoring: regulates the length of the briquette to a constant level Pressing area wear bush: Prevents wear in the pressing area Location: Ex works - free loading

Year of construction: 2025, condition: new, Sandblasting cabinets for clean blasting work without soiling the working environment. Suitable for various blasting materials, e.g. quartz, glass ball, plastic ball, etc. Ideal for cleaning, derusting or paint removal from metal parts of all kinds, e.g. engine parts, fittings, signs, housings, rims, hinges. High-quality latex work gloves are firmly attached to the housing Iisdpfx Ascqm Rwoabjh Viewing window with glued-on protective film enables optimum visibility and work protection during workpiece processing Dust-free working due to all-round seals on lid and door frame Sturdy storage grid allows workpieces to be placed inside the cabin With drain opening for changing the blasting material Suction pipe for the blasting material fixed at the bottom of the collecting container With compressed air connection on the outside Very large, upward opening front flap with gas pressure springs for quick and easy loading and unloading Integrated extraction system with replaceable air filter Blast gun without finger trigger ? Control of the air flow via foot pedal 4 fluorescent tubes (230 Volt), in separate housing with protective screen and exchangeable protective foil, including 5 spare foils 2 separate switches for suction and cabin lighting regulation of the working pressure via pressure regulator with manometer Cross struts on the feet allow easy transport with a pallet truck Scope of delivery: High-quality blasting gun with ceramic nozzle 4 pieces ceramic nozzles (4

Condition: new, Year of construction: 2025, Holzkraft Minimax ST 5es - Maximum equipment for professionals Saw-milling combination with miter cutting device and swiveling milling spindle Art. No.: 5501086 Ø 350 mm main saw blade with 118 mm max. cutting height, which is also achieved when the scoring saw blade is installed Scoring unit with separate motor and Ø 120 mm saw blade, easily and precisely adjustable from the outside Saw unit can be tilted from 90° to -45 High-precision format sliding carriage made of anodized aluminum Large extension arm (1200 x 650 mm) With material roller and extendable aluminum telescopic fence up to 3300 mm Pivoting milling spindle from 90° to -45° backwards into the milling fence Four milling speeds With right-left rotation of the milling spindle Three independent motors With lockable main switch, motor protection switch With separate saw-parallel fence and separate jointing fence for dressing as standard Equipment details: Sliding carriage with ball contact system Made of anodized aluminum Guides made of hardened and ground steel, 15% harder than conventional steel Double cradle milling unit Swiveling, made of cast iron Fixing points directly on the table, thus optimal running smoothness Milling spindle mounted far up on precision ball bearings, thus low bearing load and longest possible service life Powerful industrial motors Milling stop Heavy-duty professional version The high-quality milling fence made of cast iron is supplied with fine adjustment as standard 3-fold positionable for quick return of the setting With fine adjustment via toothed rack, numerical display and aluminum milling stop jaws Rip fence With fine adjustment and quick clamping Sturdy round bar guide made of ground steel Conveniently folds down for cutting large workpieces Reversible aluminum ruler for narrow workpieces Cast iron double weigh saw unit Height adjustment via dovetail guide Extremely robust and torsion-resistant for precise cuts Close to the saw blade, mounted on both sides Height and up to 45° inclination adjustable Scoring unit with separate scoring motor 0.55 kW as standard Boom with angle-adjustable telescopic crosscut fence with degree raster graduation Dimensions and weights weight approx. 900 kg Connection dust extraction diameter of dust extraction nozzle 3 x 120 mm Suction port diameter saw blade guard 80 mm Drive power scoring motor 0,55 kW main motor 2 x 5,0 kW Electrical data Supply voltage 400 V Format sliding carriage and table Width of sliding table 360 mm height of sliding table 142 mm Table length 1380 mm table width 465 mm Milling spindle spindle inclination 0 - -45 ° useful length of spindle 125 mm spindle speeds 3500/6000/8000/10000 min-¹ Milling tool diameter max. lowerable 240 mm tenon milling 320 mm Circular saw unit and scoring unit trimming length 3200 mm Cutting width with rip fence 900 mm Max. Trimming width to the left of the saw blade 3300 mm saw blade inclination 90 - 45 °. Iiedpfx Aajd Hx Hmobeh Max. Cutting height 90° 104 mm Max. Cutting height 45° 68 mm Location: Ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, Raw air extractor ASA 141 With standard undercarriage Dimensions and weights Chip collection volume 175 l Nominal width external suction inlet 140 mm Length approx. 1062 mm Width/depth approx. 648 mm Height approx. 2300 mm Weight approx. 40 kg Electrical data Supply voltage 230 V Mains frequency 50 Hz Filter Filter area 1.9 m² Noise emission Sound pressure level max. 78 dB(A) Iodshk S Swepfx Aabeih Volume flow Nominal volume flow 1650 m³/h For milling, planing and sawing chips (no dust) Substantially reduced dust content due to BIA-tested filter material with high separation efficiency Housing parts and impellers made of high-strength special plastic Quick release fasteners for filter and chip bags for unproblematic maintenance Robust, high-quality design Easy to move due to swivel castors Low power consumption Suction units comply with dust class L Scope of delivery: System body with mounted fan unit Filter bag / extraction unit chip bag / extraction unit without suction hose

Condition: new, Year of construction: 2025, Gannomat Concept 70 Eco Lamella - carcass press with rapid traverse Technical data: Lamella carcass press from our showroom; Working range: width from 150 - 2.500mm , height from 150 - 1.400mm; depth 700mm; - lamella press beam top with 6 elements, lamella press beam side with 5 elements - lamella press beam with practice-proven tolerance compensation for tightly pressed carcass joints - Counterpressure surfaces are 40 mm thick, coated continuous support plates - The pressing force of the pressing bars is infinitely variable electronically controlled by 2 potentiometers and adjusted via frequency converter, therefore the torque transmission is absolutely wear-free. - Pressing force for horizontal press bars min. 500 daN (kg) to infinitely variable max. 2200 daN (kg) - Pressing force for vertical press bars min. 300 daN (kg) to stepless max. 2200 daN (kg) - Including option: Rapid traverse speed for fast positioning of the press bars, controlled by automatic workpiece recognition with sensors in the press bars, press speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. Iedpfx Aaoiidm Nebjih - Jog mode for precise positioning of the two pressing beams e.g. for low pressing forces, drawers and carcasses 45 degrees. Simple operation via 6 separate pushbuttons, freely adjustable pressing time preselection with automatic opening, loading height 300 mm. Machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, Hoku BK119-270-10-VKK upright piston compressor with refrigerant dryer, automatic condensate drain, oil-water separator, pre- and fine filters, mounted with rubber vibration dampers on a safety pallet. Universal piston compressors with belt drive and high-quality features. Pressure vessel manufactured according to German AD 2000 regulations. Intake capacity: 650 l/min Effective delivery rate: 520 l/min Iijdpfjr Ig Ahex Aabeh Maximum pressure: 10 bar Tank volume: 270 l Cylinders/stages: 2/2 Speed: 920 rpm Motor power: 4 kW/400 Volt Air throughput: 650 m³/h Motor power: 4 kW Machine dimensions: 1200 x 800 x 2000 mm Pressure vessel: 270 L Effective delivery volume: 520 L/min Intake volume: 650 L/min Maximum pressure: 10 bar Location: ex stock 54634 Bitburg - immediately available -

Condition: good (used), Year of construction: 2000, Gebr. Esta Dustomat 62 Suction nozzle Ø: 160 mm Main motor: 3 kW Item description: mobile, CE mark, 3 KW, Ø=160 mm, Iodpfx Asvk Drtjabsih Filter cleaning mobile separation container, Nominal volume flow 1,850 m³ / h Location: from stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, Holzkraft Edge Sander: KSO 150 F PRO Iedpfx Aov Sk Nnsabeih With oscillating sanding belt for the best sanding results Item number: 5390020 Brand: Holzkraft Sanding unit can be pivoted using a hand crank The welded steel machine stand guarantees high torsional rigidity and vibration-free operation Oscillating sanding belt with separate gear motor for better sanding results Oscillation can be optionally activated Granite-coated sanding sole for a longer sanding belt service life Height-adjustable sanding table for utilizing the entire sanding belt width Additional table with extraction openings for sanding radii on the rubberized guide roller Sanding sleeve device with attachable work table The spring-loaded belt tension automatically compensates for belt length differences With adjustable stops, ideal for veneer sanding The grooved veneer stop allows the veneer overhang to be adjusted TECHNICAL DATA Dimensions and Weights Length (product) approx. 1700mm Width/Depth (product) approx. 1000mm Height (product) approx. 1150mm Net weight approx. 300kg Extraction connection Number of extraction nozzles: 2 Extraction nozzle diameter: 100mm Worktable(s) Worktable length: 950mm Worktable width: 450mm Worktable height adjustment: 110mm Electrical data Connection voltage: 400V Mains frequency: 50Hz Oscillation motor power: 0.11kW Sanding unit Sanding belt length: 2640mm Sanding belt width: 150mm Belt rotation speed(s): 14m/s Oscillation stroke: 15mm Sanding surface length: 800mm Sanding surface width: 150mm Sanding unit pivoting 0 – 45° SCOPE OF DELIVERY 1x Sanding Belt K100 5x Rubber Rollers Ø25, Ø30, Ø40, Ø45, Ø50 mm 6x Sanding Sleeves K80 - Ø25, Ø30, Ø35, Ø40, Ø45, Ø50 mm On-Board Tool Kit Miter Gauge

Condition: new, Year of construction: 2025, Clean Air Dust Extractor: RLA 140 For wood dust and shavings, designed for commercial use Item number: 5131400 Brand: Holzkraft DESCRIPTION Dust-tested according to H3, residual dust content less than 0.1 mg/m³ Suitable for extracting and separating dry wood and plastic shavings High extraction performance with minimal space requirements Maximum performance in this class Very quiet All models with collision protection Iedev Sk Tmepfx Aabsih Area of application Designed for commercial use For all woodworking machines with the appropriate extraction nozzle diameter High-quality, well-thought-out design Robust and compact housing made of galvanized sheet steel Extraction nozzle can be easily converted from left to right, allowing for flexible use Large inspection openings Large, mobile chip container with clamp and chip collection bag Dust extractor already installed upon delivery Fully assembled, allowing for quick deployment. All models are mobile. Model RLA 210: Optimal chip distribution into the chip containers due to the large filter surface. Filter Description Ultra-compact with maximum filter surface. Filter material made of aluminum-coated polyester fleece, thus offering a long service life. Filter tested and approved as standard in antistatic design according to category M-BIA. The fan is installed downstream of the filter. TECHNICAL DATA Dimensions and Weights Length (product) approx. 1241 mm Width/Depth (product) approx. 830 mm Height (product) approx. 1750 mm Net weight approx. 210 kg Chip collection volume 165 l Nominal diameter of the extraction nozzle inlet: 140 mm Axis of the extraction nozzle to the floor: 850 mm Electrical Data Supply voltage: 400 V Mains frequency: 50 Hz Efficiency class of the extraction motor IE3 Drive motor power: 2.2 kW Filter Filter area: 8.5 m² Residual dust content: < 0.1 mg/m³ Manual filter cleaning Noise emission Max. sound pressure level: 71 dB(A) Flow rate Nominal flow rate: 1108 m³/h Max. flow rate: 1750 m³/h SCOPE OF DELIVERY Metal fan impeller Inspection opening for cleaning the bypass filter 5 m connection cable with 5-pin CEE plug and phase inverter Two fixed and two swivel casters with parking brake Manual cleaning