Used Wedge for sale (469)

Condition: new, machine/vehicle number: 5c7120ea17bcf92d3b69899da, empty load weight: 14 kg, maximum load weight: 35 kg, overall weight: 50 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with exchangeable 2 king pins 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2x wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit with spray flaps behind each axle 1x storage box Box, w=2 350 mm x l=730 mm x h=640 mm, bolted transversely at the front to the floor of the gooseneck, with 2 storage trays Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Excavator trough above the rear axles starting to the rear, approx. 500 mm wide and approx. 230 mm deep Low loader lashing eyes Bjdei Ri Hgjpfx Abzjww 3 pairs of lashing eyes per 10 tons at the front gooseneck, 8 pairs of lashing eyes per 10 tons in the low bed, 3 pairs of lashing strips in the tramline area of the low bed, 3 pairs of lashing eyes per 10 tons in the axle/rear area Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Hydraulic forced steering via saddle deflection wedge acting on all 3 axles, Post-steering with radio remote control + auto toe-in, (up to max. 20 km/h)Note! A 2-pin Nato socket with at least 2 x 35 mm² is required in the truck for the power supply to the steering system. Power is supplied to the pump unit via a Nato connection cable to the towing vehicle, without truck installation (re-steering must be used once a week). Air suspension Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable With lifting & lowering valve, hold function in lowering position + auto-reset function Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle driving stability system Trailer Infocenter, for displaying vehicle data such as axle loads (no calibrated scales), mileage and diagnostic/system messages. Electrics 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white LED position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1x additional LED work light(s) at the rear, switched via reversing light 1x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck with steel / checker plate covering In the tramline area with 70 mm softwood floor, in the wheel housing area with steel / checker plate covering, low bed can be raised hydraulically on the left and right in the tramline area for entry, via truck auxiliary drive Rear slope with 70 mm softwood floor Drop deck length approx. 6,300 mm Drop sides 25 mm aluminum h

Year of construction: 1989, condition: ready for operation (used), Media Chip conveyor Yes This MORI SEIKI SL 25 was manufactured in 1989. It is a horizontal turning machine equipped with a three-jaw chuck, dead-collet head, chip conveyor, and tailstock. Clamping wedges for tools are also included. Consider the opportunity to buy this MORI SEIKI SL 25 horizontal turning machine. Contact us for more information. Bwedpfsxiri Tex Abzow Application Types Turning

Condition: new, Year of construction: 2025, throat depth: 280 mm, ram adjustment: 85 mm, table height: 755 mm, drop-through hole in table: 190 mm, table width: 540 mm, table length: 740 mm, stroke adjustment: 100 mm, pressing force: 80 t, ram bore: 40 mm, power: 7.5 kW (10.20 HP), punching force: 80 t, Equipment: safety light barrier, A TYPE ECCENTRIC PRESSES GENERAL FEATURES  Steel construction body,  Stress relief will be applied to the body and welded parts with vibration.  Parallelism and perpendicularity tolerance between tables in accordance with ISO and DIN standards  Pneumatic clutch and brake combination – OMPI-Italy  Ram supported by 8 slides  Parts such as ram, connecting rod, claw are cast steel, GS52  High strength solid crankshaft – 4140  Inside of connecting rod will be bronze, (Zr14)  With spare table,  With hydraulic fuse  Ratchet apparatus table-ram adjustment  Automatic central lubrication,  Pneumatic pedal with ratchet and double hand control with time adjustment,  With electric counter,  PLC application and touch screen – DELTA  Electrical switchgear materials – SIEMENS-SCHNEIDER  Double coil safety valve – GPA, TOPAIR  Locked position switch and panel,  OPTIONAL FEATURES  CE application  Finger protection beam barriers – SICK, LEUZE, KEYENCE  Security PLC (Controls the entire electrical system, valve, double and pedal) – PILZ  Safety wedge,  Protective enclosures will be within the scope of CE.  Speed Control Application  Automatic Lubrication System BODY A TYPE MONOBLOCK BODY TYPE A SERIES Capacity 80 Tons Throat Depth 280 Mm Table-Ram Distance 400 Mm Slide-Table Distance 420 Mm Wall Distance 470 Mm Ram Adjustment 85 Mm Press Width 1000 Mm Press Depth 1735 Mm Bedpfx Abevxtgiszeww Press Height 2300 Mm Front Anchor Dimension 720 Mm Side Anchor Dimension 1040 Mm Table Hole Diameter 190 Mm Table Size 540 / 740 Mm Mold Clamping Housing Diameter 40 Mm Ram Size 370 / 230 Mm Floor Table Dimensions 755 Mm Stroke Adjustment 10 / 100 Mm Stroke Number/Minute 50 Units/Min. Motor Power 7.5 KW Motor Speed 1450 RPM Weight 4,500 Kg ROLL UNCOUNTER AND ROLL DRIVER WILL BE PRICED EXTRA IF REQUESTED. IT IS NOT INCLUDED IN THE PRICE OF THE PRESS.

Condition: good (used), Technical Data for Pallet Rack System: Racking System: Vogelsang Type: NS Technical Data for Installation: Number of rack rows: 01 unit Length per rack row: 11,150 mm Number of sections per rack row: 04 units Technical Data for Capacity: Pallet spaces per section: 09 units Pallet spaces per rack row: 36 units Total pallet spaces: 36 units Assumptions: Load carrier: Euro pallet EN 13698-1 Dimensions: 1,200 x 800 x 150 mm Total height incl. pallet: n/a Maximum weight per pallet: 900 kg Scope of supply includes: 05x pallet rack uprights, used Colour: green Profile dimensions: P 70 x 80 x 2.50 mm Incl. horizontal and diagonal bracing, foot plates The uprights are pre-assembled (bolted frame) Height: 3,600 mm Depth: 1,100 mm 16x pallet rack beams, used Colour: orange Box profile: 110 x 50 mm End connector: 4-hook Clear span: 2,700 mm Max. load capacity per pair of beams: 2,700 kg, with evenly distributed load 32x safety pins, used Finish: sendzimir galvanized To secure the longitudinal beams against accidental lifting 20x wedge anchors, new Manufacturer: Hilti Model: HST2 M12x105/10 Material/finish: carbon steel, galvanized Approved for: cracked concrete 10x levelling plates, used Finish: completely galvanized For levelling uprights installed on uneven floors 01x load sign With details of section and level loads, manufacturer, and order number Dimensions: 420 x 297 x 3 mm Your contacts at our company: Bwsdpfxew Tykho Abzjw Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information regarding this item: This item is offered for collection only. Any requested transport or shipping will incur additional costs, which can be provided upon request depending on delivery location and scope.

Condition: used, empty load weight: 7,400 kg, maximum load weight: 27,400 kg, overall weight: 34,800 kg, axle configuration: 3 axles, first registration: 01/1989, loading space length: 12,800 mm, loading space width: 2,450 mm, loading space height: 2,450 mm, loading space volume: 77 m³, total length: 2,500 mm, total width: 3,750 mm, suspension: air, tire size: 14/80R 20, color: white, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 3-axle, air-suspended, last axle positively steered, ABS (anti-lock braking system), roller shutter, aluminum side bumpers, supports Bedpfovhhflsx Abzjww Body: box semi-trailer with roll-up door, last axle positively steered via wedge, was used by the previous owner as a factory-internal semi-trailer (for trade fairs). The trailer is currently being rented out but can be viewed at any time! ACCESSORIES WITHOUT WARRANTY, changes, prior sale and errors excepted! - .

Condition: like new (used), ffor PAUL KME 2 or BM edger and multirip saw, overall length 420 mm, 160 mm or 105 mm, clamping length 375 mm, 110 mm or 55 mm, bore Ø 60 mm, outer Ø 75 mm, flange Ø 120 mm, 2 external wedges, saw bushes with left-hand thread or right-hand thread available Bsdpfx Ajpky Aajbzeww

Condition: new, machine/vehicle number: 7272fc3b6a97f9be58a222f05, empty load weight: 5 kg, maximum load weight: 32 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Fine-grained steel welded construction, fifth wheel plate with interchangeable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with incl. guide wedges on both sides Incl. guide wedges, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 30 foot or 1 x 40 foot container. Adjustment via central telescope as an interlocking central tubular frame with bolt lock. Optimum fifth wheel load when transporting 30 foot and 40 foot containers. 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Hydraulics 100 Low-pressure cylinder max. 150 bar, with HDK screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Incl. Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 170 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Bjdoi Riv Espfx Abzeww Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck instal. calibrated scales) Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light

Condition: excellent (used), functionality: fully functional, power: 25.01 kW (34.00 HP), fuel type: diesel, color: black, fuel: diesel, gearing type: hydrostat, Year of construction: 2018, operating hours: 714 h, Equipment: air conditioning, all wheel drive, hydraulics, KÄRCHER MIC 34C Bwjdsu Th E Ropfx Abzew Municipal tool carrier with winter service equipment consisting of: - KUGELMANN silo spreader with 320l volume and control panel - KUGELMANN Wedge-Vario snow plow with 140cm max. clearing width This KÄRCHER MIC 34C was built in 2018, has only 714 total operating hours and 261 hydraulic hours according to the counter and is in a well-kept overall condition with normal signs of use and wear, fresh from the major customer service, ready for immediate use, cf. NP € 80,000! - Net price 31.900,-€ // Gross price 37.9611,-€ ) - Viewing / test drive possible - Shipping can be organized nationwide, the costs depend on the distance! - Our leasing partner will be happy to provide you with an attractive leasing / financing offer!

Condition: new, Year of construction: 2025, Device description Bodjwnxcmopfx Abzeww The splitter has an overload valve that drains oil to the tank and an efficient, failure-free gear pump. The tree lifting system makes it easier to place heavy materials directly under the splitting wedge 5-pin power connection The wedge set at an angle makes it easier for the wedge to sink into the material. FAILURE-FREE HYDRAULIC PUMP 24l! Technical parameters Pressure force 22 TON Minimum wood diameter 80 mm Maximum wood diameter 700 mm Minimum wood length 350 mm Maximum wood length 1100 mm Splitting speed (continuously adjustable) 10.5 cm/s Return speed 7.5 cm/s Wedge stroke length 948 mm Total engine power (S1;S6) S1:5.1 kW S6: 6.6 kW Voltage 400 V Hydraulic tank capacity 24 l Hydraulic system pressure 27.7 Mpa Dimensions 1050 x 1550 x 2500 mm Weight approx. 320 kg

Condition: excellent (used), Year of construction: 1972, Precision lathe, turning machine, lathe, center and feed lathe, center and feed lathe -Manufacturer: VDF Heidenreich & Harbeck, lead screw and feed screw lathe type 24R0 -Machine bed: hardened Bwedpfow Sxgxjx Abzew -Turning length: 1230 mm -Turning Ø over bed: 500 -Turning Ø over recess: 355 mm -Turning Ø over support: 290 mm -Spindle bore: Ø 56 mm -Spindle speeds: 19 - 2000 rpm -Wedge bar chuck: Forkardt Ø 250 mm -Tailstock mount: MK4 -Drive: 5.5 kW -Accessories: 1x steady rest, 7x Multifix tool holder, see photos -Dimensions: 1180/3050/H1345 mm -Weight: 1907 kg

Condition: used, functionality: unexamined, Year of construction: 1999, machine/vehicle number: 201805015, pressing force: 220 t, working length: 3,050 mm, Used press brake. 220 ton 3 meters 6 axes Technical specifications Voltage: 400 V Type: PPEB 220/30 Force: 2200 kN Working length: 3050 mm Distance between uprights: 2600 mm Stroke: 250 mm Table/ram opening: 485 mm Throat depth: 400 mm Approach speed: 100 mm/s Working speed: 9.6 mm/s Return speed: 113 mm/s Motor power: 22 kW Oil capacity: 350 l Machine weight: 14,500 kg Control: CADMAN CNC Table width: 150 mm Noise level: 80 dBA Pump flow: 48 l/min Pump model: Voith IPV 4-32 High precision and high flexibility. The PPEB press brake is a robust, highly technological machine. PPEB gives you the freedom to configure a press brake to suit your production requirements. Automatic crowning The crowning system counteracts machine deflection to ensure precise and repeatable bending. Our wedge system is custom-built for each machine and provides crowning along the entire table length. Robust structure A single-piece welded frame guarantees the machine’s precision. Bedpfxswzw Smj Abzjww

Condition: good (used), Year of construction: 1981, Ref. -No.: 10447 Manufacturer: SKODA Type: WD 200 Year of construction: 1981 Retrofit: 2010 Type of control: CNC Control: SIEMENS SINUMERIK 840D Storage location: Halberstadt Country of origin: Germany X-Travel: 9000 mm Y-Travel: 4000 mm Z-Travel: 1450 mm W-Axis: 2000 mm Bed width: 2000 mm Bed height: 550 mm Spindle Diameter: 200 mm Quill Stroke: 1600 mm Rotary Table (Lxw): 4000 x 4000 mm Table Load: 80000 kg Clamping Area: 3000 x 3000 mm Turning Speeds: 257 - 2570 RPM Spindle taper: 120 Automatic feeds: 342 mm / rev Spindle Turning Speed - Stepless: 1,5 - 630 RPM Max. Torque On The Boring Spindle: 20000 Nm Rapid Traverse: 16000 m / min Drive Capacity - Spindle Motor: 9,8 - 35,5 kW Total Power Requirement: 75 kW Bore Depth: 2000 mm Bedpfx Aow Upfdebzeww Vertical headstock movement on the column: 3150 mm transverse movement of the stand on the bed: 4000 mm Lowest position of the spindle axis above the bed: 1100 mm Spindle speed when moving the quill forward: 1,6 - 300 max. rpm Drill feeds (spindle, quill) continuously variable in the range: 1,6 - 1600 mm / min Milling feeds (headstock vertical, column horizontal) infinitely variable: 1,6 - 1600 mm / min Machine length: 11350 mm Machine width: 5450 mm Machine Height: 7350 mm Weight Of The Machine Ca.: 65 t Further information: Threading: 22 metric threads, pitch range 0.5 - 12mm 32 Whitworth threads, pitch range 28 - 1 (gears) Accessories: - console for tools - 1 set of operating tools - ejector and fastening wedges for spindle - lubricating press - 1 set of spare parts for electrical equipment - clamping base plate - setting stick with electrical equipment Machine can be inspected under power by appointment.

Condition: new, machine/vehicle number: a203d9a559ff6484cf2a14c1f, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, fifth-wheel plate with replaceable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with guide wedges on both sides, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 20 foot or 1 x 30 foot container. (Note! low fifth wheel load for 20 foot containers) Adjustment via central telescope as an interlocking central tubular frame with pin lock. 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Free support foot corner dimension or free swing radius to the rear approx. 1850 mm 2 wheel chocks with holder Half-shell mudguard with anti-spray flaps according to EG Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/65 R22.5 Manufacturer's choice Steel rims, factory silver Incl. Electrics 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Bwjdpoi Ri Avefx Abzew Additional LED work light(s) at the rear, switched via reversing light Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Support legs coated black Attention: Archive pictures!

Condition: like new (used), functionality: fully functional, mileage: 6,57,810 km, power: 228 kW (309.99 HP), first registration: 07/2001, Year of construction: 2001, New engine, 3rd steering axle, Cofaral superstructure, Mechanical transmission, Total tank capacity 12,850 L, Water capacity 4,500 L in side compartments, Automatic rear tank bottom closure with wedges, Jurop PR150 decompressor 15,000 L/min, Spaggiari high-pressure water pump 190 bar 171 L/min, Main hydraulic reel Bandiera 3/4, Side hydraulic reel 1/2. Bwodpfx Ajxpnbxebzsw

Condition: refurbished (used), Year of construction: 2010, HOLTEC log infeed LINCK infeed EV40 LINCK V40 LINCK turning device DV55 LINCK infeed EV30 LINCK V25 LINCK double profiling unit VPP34 LINCK circular saw VS66 LINCK board separator SEA LINCK turning device DV35 LINCK centering device ZZP LINCK double profiling unit VP34 LINCK circular saw MKV Bwjdpfxoxpt Hge Abzjw LINCK SEK splitter wedge

Condition: good (used), Technical Data for Pallet Racking System: Racking System: SSI Schäfer Type: PR600 Technical Data for Installation: Number of rack rows: 01 pc. Length per rack row: approx. 40,680 mm Number of bays per rack row: 01 pc. at 3,600 mm Number of levels plus ground level: 02 pcs. Volume Data: Pallet spaces per bay: 12 pcs. Pallet spaces per rack row: 132 pcs. Total pallet spaces: 132 pcs. Based on: Load carrier: Euro pallet EN 13698-1 Dimensions: 1,200 x 800 x 150 mm Overall height incl. pallet: n.d. Max. weight per pallet: n/a. Scope of Delivery Includes: 12x pallet rack uprights, used Material finish: Sendzimir galvanized Frame type: P95 Profile dimensions: 90 x 75 x 2.5 mm Including horizontal and diagonal braces, base plates Uprights are pre-assembled (bolted truss design) 3,000 mm height 1,050 mm depth 44x pallet rack beams, used Material color: RAL 5010 gentian blue INP profile: 120 x 58 mm Beam type: TRV1-360-12-l Connector: 4 HK (hooks) Clear span: approx. 3,600 mm 12x rack protectors, used Height: approx. 750 mm External width: approx. 98 mm Internal width: approx. 92 mm Material thickness: approx. 3 mm Material color: RAL 1021 yellow 88x locking pins, used Material finish: Sendzimir galvanized For securing the longitudinal beams against unintentional lifting 48x wedge anchors, new Manufacturer: Hilti Model: HST2 M12x105/10 Material: Carbon steel, galvanized Approved for: cracked concrete 24x shim plates, used Finish: completely galvanized For leveling uprights on uneven floors 01x load sign With field and compartment load specifications, manufacturer and commission number Dimensions: 420 x 297 x 3 mm Your contacts in our company: Mr. Andre Evering Mr. Mario Klöver Bedpfow Davmox Abzsww Mr. Falk Deutsch General Information about the Item: This item is only offered for collection. Any further transport or shipment is associated with additional costs, which can be requested from us separately depending on the delivery location and scope.

Condition: used, functionality: unexamined, Year of construction: 1999, machine/vehicle number: 26579, control type: PLC-controlled, bending force (max.): 110 t, working width: 3,050 mm, pressing force: 110 t, working length: 3,050 mm, Used press brake 110 tons 3 meters 6 axes Technical specifications Voltage: 400 V Model: PPEB 110/30 Pressing force: 1100 kN Working length: 3050 mm Distance between uprights: 2600 mm Bodpjw Afccjfx Abzjww Stroke: 200 mm Table/ram gap: 400 mm Throat depth: 400 mm Approach speed: 130 mm/s Working speed: 12.4 mm/s Return speed: 115 mm/s Motor: 15 kW Oil capacity: 250 liters Machine weight: 9500 kg CNC control: CADMAN Table width: 150 mm Noise level: 80 dBA Pump flow rate: 38 l/min Pump type: Voith IPV 4-25 High precision and flexibility. The PPEB press brake is a robust, highly technological machine. PPEB gives you the freedom to configure your press brake according to your production requirements. Automatic crowning The crowning system compensates for machine deflection to ensure accurate and repeatable bends. Our wedge system is custom-made for every machine, representing crowning across the entire table length. Robust structure A single-piece welded frame ensures machine accuracy.

Condition: new, Year of construction: 2025, The CORMAK WS32 table drill is a solid tool with high spindle stiffness. It has automatic left-hand rotation, large spindle stroke and a clear control panel. Constructed from the highest quality seasoned castings, it offers a powerful engine and CE certification. The maximum drilling diameter in steel is 32 mm and the maximum threading diameter is M24. Equipped with an MK3 spindle mount, it ensures stability and easy tool replacement. Perfect for professional and hobby use. Characteristics of the WS32 bench drill: High spindle stiffness Threading by automatic switching of left-hand rotation Left rotation switch The headstock, column, table and column base are made of the highest quality seasoned castings Spindle and gear shafts made of hardened and heat-treated steel High engine power Large spindle stroke Clear control panel U-type spindle cover with limit switch, CE compliant Manually lifted work table with 360° rotation and mounting grooves The belt transmission cover is equipped with a safety limit switch CE certificate Adjustable drill chuck with key and Morse cone mounting A wedge for knocking out a cone Technical data MAX. DRILLING DIAMETER IN STEEL 32mm MAX. THREADING DIAMETER IN STEEL M24 COLUMN DIAMETER 100mm SPINDLE TRAVEL 150mm SPINDLE-COLUMN DISTANCE 265mm MAX. SPINDLE-TABLE DISTANCE 390mm MAX. SPINDLE-BASE DISTANCE 745mm SPINDLE MOUNTING MK3 ROTATION SPEED RANGE 280, 400, 675, 1140, 1875 rpm NUMBER OF ROTATIONAL SPEEDS 5 TABLE DIMENSIONS 380 x 400 mm BASE DIMENSIONS 645 x 470 mm MACHINE HEIGHT 1370mm ENGINE POWER 1.1 kW POWER 400V NET WEIGHT 230 kg DIMENSIONS 900 x 500 x 1400 mm Bodpfx Aerif Udebzsww Optional equipment cooling system

Condition: new, machine/vehicle number: 28b2dda4ac4da850b1010673a, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, fifth-wheel plate with replaceable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with guide wedges on both sides, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 20 foot container (Note! low fifth wheel load for 20 foot containers) 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Free support foot corner dimension or free swing radius to the rear approx. 1850 mm 2 wheel chocks with holder Half-shell mudguard with anti-spray flaps according to EG Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK Screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension 3 SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons Gross train weight Air suspension. Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck instal. calibrated scales) Wheels and tires 6 385/65 R22.5 tires of the manufacturer's choice 6 steel rims, factory silver Bwedpfx Absi Ri Euezew Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Country of registration/ plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Support legs coated black Attention: Archive pictures!

Condition: excellent (used), Year of construction: 1968, Precision lathe, turning machine, lathe, center lathe, center lathe -Manufacturer: Schaublin, lead screw and feed screw lathe type 135 -Machine bed: hardened -Turning length: 750 mm -Turning Ø over bed: 315 -Turning Ø over recess: 355 mm -Turning Ø over support: 150 mm -Spindle bore: Ø 34 mm -Spindle speeds: 45 - 3000 rpm -Wedge bar chuck: Forkardt Ø 160 mm -Tailstock mount: MK3 -Drive: 1.5/3.0 kW -Accessories: Drawer cabinet with 2x steady rests, 28x Multifix tool holders, collets, see photos -Lathe dimensions: 960/1700/H1290 mm -Weight of lathe: 1230 kg -Dimensions cabinet: 480/725/H1000 mm Bsdjw Rd Hbopfx Abzsww -Cabinet weight: 222 kg

Condition: good (used), Year of construction: 1970, functionality: fully functional, Thickness planer type DM 63, year of manufacture 1970, with 4 knives, planing width 630 mm, planing height 220 mm, cutterhead speed 5500 rpm, 4-knife cutterhead (wedge knives), 7.5 HP motor, weight approx. 1150 kg. Machine subject to differential taxation! Bodpfoxf H Amex Abzsww

Condition: good (used), Technical Data for the Pallet Racking System: Racking System: SSI Schäfer Type: PR 400 Technical Data for Installation: Number of Racking Runs: 1 unit Length per Racking Run: 108,100 mm Number of Bays per Racking Run: 39 units Scope of Delivery Includes: 40x Pallet Rack Frames, used Colour: green Profile dimensions: U 70 x 50 x 3 mm Including horizontal and diagonal bracing, frame protectors, and base plates The frames are pre-assembled (welded lattice structure) Height: 3,620 mm Depth: 1,050 mm 144x Pallet Rack Beams, used Colour: green Beam type: TRN1-270-08-I INP profile: 80 x 42 mm Connector: 5 HK Clear span: 2,700 mm Max. load per beam pair: 2,100 kg, with evenly distributed load. 288x Safety Pins, used Finish: Sendzimir-galvanised For securing longitudinal beams against unintentional lifting 160x Wedge Anchors, new Manufacturer: Hilti Type: HST2 M12x105/10 Design: Carbon steel, galvanised Approved for: cracked concrete 80x Levelling Plates, used Finish: fully galvanised For levelling frames installed on uneven floors 1x Load Sign with field and compartment load ratings, manufacturer and order number Dimensions: 420 x 297 x 3 mm Bedpfow Sr Rkex Abzoww

Condition: new, Year of construction: 2025, The WS16 table drill with a reinforced structure is a general-purpose drill for performing operations such as drilling, reaming, countersinking, threading (using special holders for tapping tools). Drills enable drilling and threading with multi-spindle holders. The drill is characterized by high efficiency, precision of operations, low noise level, wide range of rotational speeds, centralized control panel facilitating work on the machine and ease of use. Machine characteristics High spindle stiffness Threading by automatic switching of left-hand rotation Left rotation switch The headstock, column, table and column base are made of the highest quality seasoned castings Spindle and gear shafts made of hardened and heat-treated steel High engine power Large spindle stroke Clear control panel U-type spindle cover with limit switch, CE compliant Manually lifted work table with 360° rotation and mounting grooves The belt transmission cover is equipped with a safety limit switch CE certificate Adjustable drill chuck with key and Morse cone mounting A wedge for knocking out a cone Technical data MAX. DRILLING DIAMETER IN STEEL 16mm MAX. THREADING DIAMETER IN STEEL M10 COLUMN DIAMETER 70mm SPINDLE TRAVEL 100mm SPINDLE-COLUMN DISTANCE 193mm MAX. SPINDLE-TABLE DISTANCE 330mm MAX. SPINDLE-BASE DISTANCE 613mm SPINDLE MOUNTING MK2 ROTATION SPEED RANGE 480-1875 rpm NUMBER OF ROTATIONAL SPEEDS 5 TABLE DIMENSIONS 265 x 285 mm BASE DIMENSIONS 360 x 480 mm MACHINE HEIGHT 1130mm ENGINE POWER 1.1 kW POWER 400V NET WEIGHT 131.5 kg DIMENSIONS 600 x 400 x 1150 mm Optional equipment cooling system Bjdpfx Aerif S Rjbzeww

Condition: used, machine/vehicle number: d25bedc76ae946ce00df59d5c, empty load weight: 11,600 kg, maximum load weight: 35,900 kg, overall weight: 47,500 kg, axle configuration: 3 axles, first registration: 06/1982, tire size: 9,5 r17,5 zwilling, Further information 1st axle rigid, 2nd + 3rd axle hydr. positively steered with saddle deflection wedge, 1 pair of hydr. support legs incl. hand pump for emergency operation, leaf suspension, 6 storage compartments, steel riffle plate complete, air: red-yellow + electrics: 1x 7-pin Length of gooseneck approx.: 4,380 mm Length drop deck approx.: 11,300 mm Saddle height approx.: 1,200 mm Bwjdpfx Aei Riyzjbzow

Condition: good (used), Technical Data for Pallet Rack System: Racking System: Jung Heinrich Type: Esmena Installation Data: Bedpfewk I N Uox Abzoww Number of rack rows: 1 unit Length per rack row: 33,450 mm Number of bays per rack row: 12 units Number of levels (plus floor level): 2 units Volume Data: Pallet spaces per bay: 9 units Number of pallet spaces per row: 108 units Total number of pallet spaces: 108 units Based on: Load carrier: Euro pallet EN 13698-1 Dimensions: 1,200 x 800 x 150 mm Total height including pallet: n.s. Max. weight per pallet: approx. 800 kg Scope of delivery includes: 13x pallet rack frames, used Material colour: blue Frame profile: MX610 Profile dimensions: 76.2 x 63.2 x 1.8 mm Including horizontal and diagonal braces, base plates Frames are pre-assembled (bolted truss construction) Height: 2,100 mm Depth: 1,050 mm 48x pallet rack beams, used Material colour: yellow Box profile: 140 x 40 mm Beam type: N140x40 SEG Connector: 5 hooks Clear span: 2,705 mm Max. load per pair of beams: 2,400 kg with evenly distributed load 96x locking pins, used Material finish: Sendzimir galvanized For securing the beams against unintentional lifting 52x wedge anchors, new Manufacturer: Hilti Model designation: HST2 M12x105/10 Version: Carbon steel, galvanized Approved for: cracked concrete 26x leveling plates, used Finish: fully galvanized For leveling frames installed on uneven floors 1x load capacity sign With details of bay and compartment loads, manufacturer, and order number Dimensions: 420 x 297 x 3 mm Your contact persons in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information on this item: This item is available for collection only. Any transport or shipping beyond this must be requested separately and will incur additional costs, which depend on delivery location and scope of delivery and can be requested from us.