LP 60 VH1

Presona AB, Schweden Ballenpresse, LP 60 VH1

Condition: used, bore capacity in steel (diameter) 35 mm throat 280 mm bore stroke 180 mm 3 speeds 65 - 1750 U/min table-size 600 x 470 mm total power requirement 1,6 kW weight 450 kg dimensions 1200 x 800 x 2200 mm Features: - Automatic feed - Coolant device - Infinitely variable speed control - Adjustable fixed depth stop - Machine light Lrjdpfxswzmt To Afzsw - Drill chuck

Condition: reconditioned (used), Year of construction: 2013, Press container with 20 cubic meters of usable volume for roll-off tipper Aventek RM20 Built in 2013 Several available Ljdpfewifivjx Afzjrw Repaired, inspected, and serviced Large filling opening Split lid opens left/right Double-sided loading Side-hinged discharge door Ramp operation possible These machines are offered repaired, inspected, serviced, and repainted in the desired standard RAL color. We would be happy to provide a quote including delivery.

Year of construction: 1994, condition: ready for operation (used), Motor power: 15.5kW/19.5kW, pressing force: 320kN, spec. pressure: 425kN/m², machine dimensions X/Y/Z: approx. 5700mm/1900mm/1800mm, weight: approx. 6000kg. The machine has a defect due to moisture and should be checked. Ljdpjip D Rpsfx Afzerw

Condition: new, Year of construction: 2025, machine/vehicle number: 2022042210, Aluminum angled conveyor belt with substructure Conveyor belt length: 1,500mm flat + 3,000mm rising Pitch angle in bend 45°C Height of the horizontal top edge approx. 200mm PVC conveyor belt Conveyor belt EM 15/2 0+17 PVC green Belt width 500mm 31 pcs. T40 studs welded - pitch 300mm * antistatic due to threads in the fabric on the underside endlessly welded with stepped finger connection 40mm sidewall high-frequency welded on both sides * edge-free zone on both sides for tape guidance in the incline Lateral arrangement: -70+35-5+280-5+35+70 Full-surface underlay sheet Drive: Motor approx. 1.1KW Belt speed approx. 0.3m/sec * optionally controllable with frequency converter Lrodpfxsh Ellzo Afzew Connection 220/400V, 50Hz protection class IP54

Condition: used, overall weight: 24,000 kg, rotor diameter: 640 mm, number of blades: 114, rotor length: 2,500 mm, power: 247 kW (335.83 HP), No. 10023 Single-shaft shredder Vecoplan VAZ 2500 Used, year of construction approx. 2006 2022 general overhaul Since overhaul approx. 700 operating hours Areas of application: Residual wood, waste wood, packaging material, film, plastic, paper, textiles, domestic waste, commercial waste, production residues as bulk material, production residues in bales 247 kW Rotor length 2500 mm Rotor diameter 640 mm 114 pieces 60x60 cube knives, 4-row Shredding optionally to a grain size of approx. 10 - 250 mm Screen basket 50 mm Throughput capacity up to 25 tons per hour / throughput waste wood approx. 30 tons per hour Material feed with hydraulic pusher Scope of delivery: machine, hopper, control cabinet, refrigerator Mechanization optionally available Transport dimensions approx. 4750 x 4640 x 2340 mm LWH Weight approx. 24000 kg Sale on behalf of customer, ex location near 85456 Wartenberg, without dismantling, without transport and assembly Errors in description and price excepted Dismantling, transport and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale Any warranty is excluded for used machines, the following applies: “purchased as viewed” Pictures and videos serve as examples and do not represent the actual scope of delivery Lrodpfx Afowh T N Ujzow Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: good (used), Year of construction: 2011, operating hours: 20,580 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 450 kg, input current: 59 A, overall weight: 12,000 kg, transport height: 2,750 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), transport width: 2,300 mm, transport length: 8,500 mm, tank capacity: 300 l, Good day, Lsdpfxst H Rcae Afzerw We hereby offer you a used baler from the manufacturer HSM, type VK 4812. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer HSM Type VK 4812 Year of manufacture 2011 Operating hours 20,580 hours Main press force 48 tonnes Drive power 30 kW Machine weight press 12 tonnes The machine documentation is available in German. A viewing is possible by appointment in our workshop. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: refurbished (used), Year of construction: 2018, Mobile hammer mill Mobil Flex 1000 with drum magnet and discharge belt Drive: 250 Kw electric 4-hydraulic supports for lifting the machine for transportation Total weight: 33,000 kg Rotor weight: 3,000 kg Production: up to 11 to/h (depending on material size, grid size, parameter settings) With soundproof housing Dimensions: 11,750 x 2,500 x 4,380 mm Lrsdpfjph Uy Tsx Afzow Number of hammers: 24 pcs. Hammer weight: 22 kg System is being overhauled

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Lsdpfxou Thbxs Afzerw Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2008, operating hours: 40,000 h, condition: good (used), machine/vehicle number: HBC 140 2x75kW 2008 (00191), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap Ledpekcgf Hofx Afzorw After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Year of construction: 2024, condition: new, ♻ Universal use (various wood, pallets with nails, chipboard boards, waste and scrap, veneer, MDF boards, cardboard boxes, Lredpfx Aon Nwxfjfzjw plastics, textiles, tires, etc.). ✔ Power: 55/75/90/110 kW ✔ Shaft length: 1400 mm ✔ Shaft diameter: 315 mm ✔ Shaft RPM: adjustable ✔ Number of cutting knives: 60 ✔ Granulation: 15-90 mm ✔ Capacity: up to 17 m3/h* ✔ Filling opening: 1400 x 1800 mm ✔ Dimensions L/W/H: 2,20/3,10/2,80 m ✔ Weight: 7000 kg 2 years warranty or 2000 working hours