Press container

Avermann MPC 20 PEL

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Iajdpfovwlqqex Adwel Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, machine/vehicle number: wtcs750s, Westtech Woodcracker CS750 Smart - available immediately Equipment: - Tiltator can be rotated continuously - Cutting diameter: 750 mm - Grab opening width: 1,280 mm - Own weight (basic - fully equipped): 820 - 980 kg - Recommended liter output: 65 - 110 l/min - Recommended operating pressure: 230 -280 bar - Service weight of carrier vehicle: 15 - 30 t - Saw box: actively suspended - Chain lubrication of saw: grease - Optional: Power tiltator can be rotated continuously Available in multiples / fits perfectly with Magni RTH 6.30 SH & Magni RTH 6.35 SH. Can also be offered in conjunction with a Magni. Also fits Merlo. We are an official Westtech Woodcracker sales and service partner, Magni telehandler sales and service partner, JCB construction machinery sales and service partner, Mercedes-Benz service partner, Iveco service partner and, with 800 used vehicles, one of the largest commercial vehicle dealers in Germany. Iedpfx Ajiady Eedwoal We supply the complete Westtech Woodcracker range for you!

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Iaodpfsvgrh Ujx Adwsl Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: used, Year of construction: 1988, operating hours: 1 h, machine/vehicle number: V 516, total width: 2,000 mm, total length: 7,000 mm, total height: 1,800 mm, operating pressure: 300 bar, pressing force: 90 t, sheet thickness aluminum (max.): 5 mm, power: 11 kW (14.96 HP), empty load weight: 16,000 kg, cutting force: 90 t, year of last overhaul: 2025, Bale size 400x400 mm Force 1 Step 900 KN Force 2 Step 900 KN Iajdpolhqd Rsfx Adwsl Steel max. 2500-3500 Kg/Std. Aluminium max. 2000 - 3000 Kg/Std. Driving Power 11 KW Arrangement Surface 7x2x2,5 m x m Machine weight 16 to Place: Austria Aviable: 30.01.2025

Condition: reconditioned (used), Year of construction: 2005, Coupling containers, 30–32 m³, suitable for screw compactors, available for right or left configuration. Used, fully functional coupling containers from €4,000, depending on condition, excluding VAT. Delivery possible. Ijdpfx Ajgypd Hsdweal

Condition: ready for operation (used), Hsm HL 4809 LI baler - Large filling opening, ideal for big boxes - Container tipper for convenient filling Pressing force in kN: 480 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 400 kg - Bale dimensions (length x width x height in mm): 1200 x 1100 x 750 - Machine dimensions (length x width x height in mm): 5648 x 1849 x 2515 Idle cycle time in seconds: 53 Iajdera Dddopfx Adwol - Manual tying: 4 times with wire

Condition: new, Year of construction: 2025, Klanke roll slitter for efficient shredding of reject rolls. Features: - Automatic safety lock - Knife guard - Emergency stop ripcord - Siemens PLC Isdpfxon Hy H Ns Adwoal Technical Data: Blade length: 1500 mm Cutting channel opening: 800 mm Motor power: 7.5 kW Cutting force: 30 tons Made to order Price and further information on request. We are happy to provide you with a non-binding offer.

Condition: new, Year of construction: 2025, Engine power 7,5kW - Cutting force 30to Cutting channel designed for - max. roll length 1500mm - max. roll diameter 850mm - machine weight approx. 3500kg - tank capacity approx.110liter - hand guard in the area of the control panel and opposite to it Isdpfsgl Adzsx Adweal -knife lock -splitter table straight execution -documentation 2-fold German ( 1x text form, 1x CD ) -color RAL 5012 - light blue protective grid/knife bar RAL 1028 melon yellow machine in stock and immediately available Price and further info on request

Condition: excellent (used), Year of construction: 2021, Coated web width 1315 mm Max. web width 1330 mm Max Core width with expanding chucks 1300 mm Max Core width with Standard cones. 1340 mm Minimum web width 650 mm Unwinder reel diameter 1000 mm Iodowqdikopfx Adwsal Rewinder reel diameter. 1000 mm Core size - unwinder: 3”= 76 mm & 6”= 152 mm - rewinder 6”= 152 mm Max. web tension - unwinder 40 kg (400 N) - rewinder 55 kg (550 N) Taper tension on rewinder up to 60% of the set value. Min. web tension - unwinder: 2 kg (20 N) - rewinder: 4 kg (40 N) Max reel weight: 1.000 kg Max mechanical speed: 450 m/min

Condition: good (used), Year of construction: 2009, functionality: fully functional, Weight 4950 kg, total weight 12000 kg 5.5 kW Isdowpmckspfx Adwoal