Bale press

Presona AB LP 100 CH2 S

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm Kdedpfsfx Hv Hex Ac Nsl clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Kjdpfx Acsvf E Avo Nedl Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, - Adhesive application with 1 profiled roller for Packaging height 300mm Kdodecht Nyopfx Ac Nol over 1 application roller - The drive via worm gear motor 0.37 kW - 1 ST left - 1 ST right - Fits DIMTER HK 200 and HK 400 spare parts dimter in stock equipment in stock accessories in stock

Condition: good (used), Year of construction: 2014, operating hours: 18,520 h, Single-shaft shredder, especially suitable for secondary shredding and granulation of pre-shredded material. Application: Commercial waste for thermal or material recovery, e.g. paper, cardboard, plastics and foams, rubber, leather, textiles, floor coverings, etc. Lindner Power Komet 1800 Year of manufacture: 2014 Control cabinet; complete with ABB frequency converter, Recooler Operator panel Hopper Drive motors: 200 kW Hydraulic unit: complete Ksdpswxmb Esfx Ac Nsdl Total weight approx. 21 t Dimensions approx. LxWxH mm: 5000 x 2800 x 3000 mm Inspection: possible upon arrangement. Delivery time: immediate.

Condition: excellent (used), Year of construction: 2014, operating hours: 37,656 h, functionality: fully functional, pressing force: 85 t, filling opening width: 1,500 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 650 kg, overall weight: 25,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2024, volume flow: 410 m³/h, transport width: 2,400 mm, transport length: 9,300 mm, Hello, We are offering you a used baler from the manufacturer Presona AB, type LP 85 VH1, subject to availability. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours, as of March 2025 Main press force: 85 t Specific press force: 100 N/cm² Kjdev T I Evjpfx Ac Nodl Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying system: 5-fold vertical Hydraulic oil tank volume: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Press weight: approx. 25 t Note: The machine was used for compaction at a recycling plant. Used for the production of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have been replaced over the past three years. The machine has been regularly serviced. We would be pleased if this press is of interest to you. Your service team at Mertens & Frowein GmbH

Condition: used, Year of construction: 2022,

Year of construction: 2012, operating hours: 1 h, condition: used, Transmission: Automatic Power: 1 kW (1 HP) Empty weight: 20.000 kg Please contact Emal Jaweed for more information Ksdpfx Aex R T D Dec Nsdl

Condition: good (used), Year of construction: 1981, functionality: fully functional, Equipment: documentation/manual, Automatic channel baler BOA Continu 25 LB + conveyor belt. The baler is in good condition and has been regularly serviced. Recently, the Denison pump underwent a complete overhaul. Fully functional and in continuous operation. Please contact us for further information. Kdsdpow S Tv Uofx Ac Nsl

Condition: used, functionality: fully functional, Year of construction: 2008, - Machine in very good technical and visual condition - Immediately available - Sale includes: - Scrap shear: Zato FCE40 or Genesis GXP400R Kodpsy Dc Nvsfx Ac Nodl - Boom - Additional attachments available at extra cost

Condition: excellent (used), Year of construction: 2014, operating hours: 8,900 h, machine/vehicle number: LP50VH2, 1) Technical specifications Press with conveyor Technical data baler: Manufacturer Presona Typ LP 50 VH2 Year of construction 2014 Press power main press 50 tons Specific press force 63 N/cm2 Feed channel 1,500 x 1,100 mm Filling volume 2,7 m3 Theoretic throughput capacity 730 m3/hour Throughput capacity under operating conditions 340 m3/hour Bale size 1,100 x 720 mm, lenght variable Drive power 45 kW Ksdpjyrhi Nefx Ac Nedl Tying system 5-fold, vertical, fully automatic Throughput capacity at a • bulk weight of 30 kg/cbm 8 up to 10 tons/hour • bulk weight of 50 kg/cbm 11 up to 13 tons/hour • bulk weight of 100 kg/cbm 15 up to 22 tons/hour Bale density (paper, newspaper) 400 up to 550 kg/m3 Filling volume hydraulic oil tank 600 l Weight baler 16 tons netto Scope of delivery: Press, electrical cabinet, control panel, chain conveyor The documentation (operating manual, CE declaration, electrical/hydraulic diagram) is complete. Visiting is possible by appointment. We are not responsible for technical information or any errors. Upon request, we can send video materials of the working press