T-slot clamping plate STOLLE - SDT

Stolle SDT

Condition: excellent (used), overall weight: 10,000 kg, total height: 400 mm, total length: 6,280 mm, total width: 2,100 mm, T slotted bed plate STOLLE - SDT MACH-ID 9775 Make: STOLLE Type: SDT Floorplate Length: 6280mm Floorplate Width: 2100mm Hjdpfx Aajzrl A Sshju Height: 400mm No. Of T-slots: 7 Distance from T to T-slot / Jump:300mm T -slot size: 35mm Weight a plate approx.: 10000kg Number of matching pieces: 1 Length: 6280mm Width: 2100mm Height: 400mm Weight: 10000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2008, operating hours: 82,500 h, functionality: fully functional, travel distance X-axis: 5,000 mm, travel distance Y-axis: 3,000 mm, travel distance Z-axis: 1,750 mm, feed rate X-axis: 65 m/min, feed rate Y-axis: 65 m/min, feed rate Z-axis: 65 m/min, spindle speed (max.): 20,000 rpm, rapid traverse X-axis: 65 m/min, rapid traverse Y-axis: 65 m/min, rapid traverse Z-axis: 65 m/min, torque: 63 Nm, overall weight: 90,000 kg, Equipment: rotational speed infinitely variable, First commissioning: 2008 Control system: Heidenhain iTNC 530 incl. handwheel HR420 X-axis: approx. 5,000 mm Y-axis: approx. 3,000 mm Z-axis: approx. 1,750 mm A-axis: -120 / +95° C-axis: ± 360° Maximum workpiece size 3,800 mm (X-direction) 1,800 mm (Y-direction) 1,150 mm (Z-direction) Can be machined in 5 axes (90° free A-axis) in a single setup using a 300 mm long tool. Hedpfx Aozkuireaheu Machine operating hours: approx. 83,000 h Total spindle hours: approx. 37,000 h Machine bed (can be installed flush or above ground!) Dimensions: 5,000 x 2,250 x 300 mm - manufactured from EN-GJL-250 9 T-slots according to DIN 650-28H12 with a spacing of 250 mm and 125 mm from the edge 2-axis milling head, inspected by the manufacturer! Spindle power: 20 kW Spindle speed: max. 20,000 min-1 Torque: max. 63 Nm Tool holder: HSK 63A Tool clamping: hydraulic Holding torque (clamped) A & C axis: 2,000 Nm Drive system for linear axes Feed rate X, Y, and Z axes: up to 65 m/min Axis acceleration X, Y, and Z axes: up to 5 m/s2 Connection data Voltage: 400 V Frequency: 50 Hz Power consumption: 130 kW Dimensions, weights Machine footprint without peripherals: approx. 7,500 x 8,500 x 6,600 mm Total weight: approx. 90,000 kg Color Enclosure, portal, control cabinet: RAL 7035 light gray Milling head and applications: RAL color 5002 aquamarine blue Additional equipment - Minimum quantity lubrication - 50-position tool changer - Work area cover Condition of the machine The milling head has been freshly inspected by the machine manufacturer, thus partially overhauled and fully functional. Completely new machine bed from Stolle! The additional modules shown on the machine bed are not included in the scope of delivery. The extraction systems and ducts shown are also not included in the scope of delivery. The previous owner was an established Formula 1 team from Central Europe. The machine was always under a maintenance contract with the manufacturer. Currently, the machine is disassembled and stored. However, an inspection is still possible at any time by arrangement.

Condition: excellent (used), Year of construction: 2000, overall weight: 6,000 kg, total height: 300 mm, total length: 4,000 mm, total width: 2,000 mm, plate height: 300 mm, plate width: 2,000 mm, 8 units Precision Leveling wedges BILZ PK4/72 Size 200 x 200; x 80 mm Load 38.000 N/pc Levelling +5 to - 7 mm Floorplate Length: 4000mm Floorplate Width: 2000mm Height: 300mm No. Of T-slots: 6 Distance from T to T-slot / Jump:320mm T -slot size: 36mm Weight a plate approx.: 6000kg Hjdpfoy Efqxex Aahou Number of matching pieces: 1 Length: 4000mm Width: 2000mm Height: 300mm Weight: 6000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Clamping plate with T-slots and cross table, plate field, welding table, welding table, plate boring mill, T-slot plate, pallet changer -Mounting plate: with a carriage with clamping device -Quantity: 1 piece (a second plate is still available ID 21154) -Wagon dimensions: 1450/810/H1120 mm -Weight: 490 kg -Width: 1465 mm -Length: 4930 mm -Working height: 850 mm -Sheet thickness: 35 mm -Plate height: 300 mm -Plate with: supporting ribs -Groove width: 52 mm Hsdpsd Ehfmefx Aaheu -Slot spacing: 292 mm -Transport dimensions: 4930/1670/H850 mm -Weight: 5900 kg

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, feed length X-axis: 3,048 mm, feed length Y-axis: 813 mm, feed length Z-axis: 762 mm, controller model: NGC, spindle speed (max.): 7,500 rpm, number of slots in tool magazine: 30, Equipment: chip conveyor, documentation/manual, 50-taper spindle with a 2-speed gearbox. Customizable to meet your specific requirements. Ideal for working with tougher materials and larger-diameter cutting tools. Hodpfxozr U S Ne Aahou

Condition: ready for operation (used), Year of construction: 2022, operating hours: 1,936 h, travel distance X-axis: 3,048 mm, travel distance Y-axis: 813 mm, travel distance Z-axis: 762 mm, overall weight: 14,334 kg, spindle speed (max.): 7,500 rpm, spindle motor power: 22,400 W, number of axes: 4, This 4-axis HAAS VF-10/50 was manufactured in 2022. It features an impressive X-axis travel of 3048 mm, Y-axis travel of 813 mm, and Z-axis travel of 762 mm. The machine includes a robust table size of 3048 x 711 mm and a maximum table load of 1814 kg. If you are looking to get high-quality machining capabilities, consider the HAAS VF-10/50 vertical machining centre we have for sale. Contact us for further details. • Spindle nose to table (max): 35.0 in (889 mm) • Spindle nose to table (min): 5.0 in (127 mm) • Spindle • Max torque: 340 ft‑lbf @ 700 rpm (460 Nm @ 700 rpm) • Drive system: 2‑speed gearbox • Bearing lubrication: Air/oil injection • Cooling: Liquid cooled • Table • Length: 120.0 in (3048 mm) • Width: 28.0 in (711 mm) • T‑slot width: 0.626–0.630 in (15.90–16.00 mm) • T‑slot center distance: 4.92 in (125 mm) • Number of T‑slots: 5 • Max table load (evenly distributed): 4000 lb (1814 kg) • Feedrates • Max cutting feed: 360 ipm (9.1 m/min) • Rapids: X 360 ipm (9.1 m/min), Y 600 ipm (15.2 m/min), Z 600 ipm (15.2 m/min) • Axis motors (max thrust) • X: 3400 lbf (15,124 N) • Y: 4100 lbf (18,238 N) • Z: 5600 lbf (24,910 N) • Tool changer • Type: SMTC • Capacity: 30+1 • Max tool diameter (all pockets full): 4.0 in (102 mm) • Max tool diameter (adjacent pocket empty): 10.0 in (254 mm) • Max tool length (from gage line): 16 in (406 mm) • Max tool weight: 30 lb (13.6 kg) • Tool‑to‑tool (avg): 4.2 s • Chip‑to‑chip (avg): 6.3 s • General • Coolant capacity: 95 gal (360 L) • Air requirements • Air required: 4 scfm @ 100 psi (113 L/min @ 6.9 bar) • Inline air hose: 3/8 in Hsdpfxezh Hlao Aahou • Coupler (air): 3/8 in • Minimum air pressure: 80 psi (5.5 bar) • Electrical • Drive system: 2‑speed gearbox • Input AC voltage (3‑phase) low: 220 VAC, 70 A (FLA) • Input AC voltage (3‑phase) high: 440 VAC, 35 A (FLA) • Dimensions – shipping • Domestic pallet: 288 in x 102 in x 132 in (732 cm x 260 cm x 336 cm) • Export crate: 288 in x 105 in x 134 in (732 cm x 267 cm x 339 cm) • Domestic pallet with EC option: 288 in x 102 in x 140 in (732 cm x 260 cm x 356 cm) • Export crate with EC option: 288 in x 105 in x 141 in (732 cm x 267 cm x 359 cm)

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, MAZAK vertical machining center VTC 530 Year 2019 Control unit: SMOOTH G X-axis travel: 1740 Y-axis travel: 760 Z-axis travel: 660 Table length: 2300 Table width: 760 Distance between top of table and spindle nose: 180 Maximum workpiece dimensions (length x width x height): 4100x905x790 Table surface: T-slot Maximum workpiece weight: 1400 Spindle speed: 12,000 rpm Spindle connection: ISO 40 Din Rapid traverse rate, X-axis: 42000 Rapid traverse rate, Y-axis: 42000 Rapid traverse rate, Z-axis: 42000 Number of tools: 30 Coolant pressure: 15 Bar through the spindle Mayfran chip conveyor Air blow for dry machining Hedpezz Sutjfx Aahsu Synchronized tapping Center partition for tandem machining Additional pre-setter Additional light Handwheel on remote cable

Condition: ready for operation (used), Year of construction: 1999, travel distance X-axis: 5,500 mm, travel distance Y-axis: 3,000 mm, travel distance Z-axis: 1,500 mm, spindle speed (max.): 3,000 rpm, spindle motor power: 22,000 W, number of slots in tool magazine: 24, number of axes: 5, This 5-axis MECOF DYNAMILL 3000L was manufactured in 1999. It features an impressive X-axis travel of 5,500 mm, Y-axis travel of 3,000 mm, and Z-axis travel of 1,500 mm. The machine is equipped with a powerful spindle taper of ISO 50 and a tool magazine capacity of 24 tools. If you are looking to get high-quality milling capabilities, consider the MECOF DYNAMILL 3000L gantry milling machine we have for sale. Contact us for further details. • Orthogonal head: 10–3,000 rpm speed range; 22 kW power; automatic tool clamping (20,000 N clamping force) • PDFTwin 15 head (GAMFIOR electrospindle): 600–24,000 rpm speed range; 17.5 kW motor power; E18 electrospindle • Indexed positioning platform: 360 positions; ±180° rotation range; ±0.02/300 mm positioning accuracy; 45,000 Nm axial clamping force • PDFContinuous positioning platform: 360,000 positions; ±185° C-axis rotation range; 0–2,400°/min C-axis rotation speed; 2,000 Nm clamping torque Additional equipment Hedpfjznv Tgjx Aahsu • Tool profile measurement device • Cart-type head magazine • BLUM radio-transmitted laser probe • Air/oil tool cooling system • MECOF High-Speed Milling system Technical Specification Taper Size ISO 50

Condition: good (used), Year of construction: 1990, total height: 350 mm, total length: 5,100 mm, total width: 1,500 mm, T slotted bed plate STOLLE - Cast iron Floorplate Length: 5100mm Floorplate Width: 1500mm Height: 350mm No. Of T-slots: 5 Distance from T to T-slot / Jump:300mm T -slot size: 28mm Hodpfxexdwwfs Aahju Weight a plate approx.: 5800kg Number of matching pieces: 1 Length: 5100mm Width: 1500mm Height: 350mm

Condition: new, Year of construction: 2026, Technical Data Control System: Multi-axis real-time interpolator with active trajectory prediction, LAN and EtherCat communication, sampling time below 1 ms, RTCP, remote service access. Working Area: X: 2000-4700 mm; Y: 3000-30000 mm Z-Axis Clearance: up to 3000 mm Drive System: Servo drives with EtherCat protocol; X, Y, Z axes equipped with hardened, ground, helical racks accuracy class 6 Linear Bearings: Trapezoidal rails; quadruple guideway size 35 for Y axis, triple guideway size 35 for X and Z axes Traverse Speed: X, Y up to 25 m/min; C, A up to 6000 degrees/min Program Resolution: 0.0005 mm Positioning Accuracy: 0.01 mm Gantry Drive: Dual-sided master/slave with gantry angle correction Electrospindles: up to 50 kW Electrospindle Inverter: Yes Maximum Electrospindle Speed: 24,000 rpm (optionally 6,000 – 40,000) Construction: Welded steel, stress-relieved, precision-machined gantry design Table Type: Modular T-slot (steel or aluminum), separated from the main construction Available Additional Options: 3D printing head Tool cooling Tool changer: linear, mobile linear, turret, or chain type Cutting saws Laser scanner Wireless measurement probe Machining area separators Compensation map Roll-up roof Vacuum table Suction foot for 5-axis heads Dedicated CAD/CAM software 3D granulate printers can process a variety of plastics such as PLA, ABS, PETG, polyamides, or polypropylene. Hedpjwhxcgjfx Aahju #router #CNC #millingmachine #millingrouter #machiningcenter #3axis #4axis #5axis #3D #3Dprint #MDF #HPL #Plywood #chipboard #steel #aluminum #brass #stainlesssteel #castiron #polypropylene #polycarbonate #acrylic #fermacell