Guide rail arc guide

THK HCR35A2RR+60/800R

Year of construction: 2002, condition: like new (used), machine/vehicle number: 16.34.02, 6 Die 6 Blow Header MULTIPRESS MP610LS Maximum Cutoff diam. (500/Nmm2): 12 mm Max. Cutoff length : 105 mm Max. KO length (die side): 80 mm Csdpsh Tkraefx Addohf Max. PKO length: 23 mm Max. Speed: 180 ppm

Year of construction: 2019, condition: ready for operation (used), Connected load: 84kVA, length: 5065mm, width: 1100mm, height: 1530mm. Csdpfx Aeg A Trgsddehf

Year of construction: 1996, condition: used, Schütte SF 26S DNT YOM 1996 Number of spindles: 6 Max bar diameter [mm]: 26 Auto bar loader: Cucchi BLT Multi-6 - (YOM 2015) Cross slide pos. 1, 3, 4, 6 CN slide pos 2, 5 Codpfxji Hb Szj Addjhf Spindle stop attachment for main spindles Bar feeding pos. 6 Pickup spindle pos. 6 High pressure coolant system Chip conveyor, hinged belt type Oil mist filter ISI RON/A 2500A, ID 26295

Year of construction: 2008, condition: used, pressure 315 t stroke 40-200 mm no. of strokes 20-100 Hub/min ram - range of adjustment 120 mm ram surface 2000x1100 mm table surface area 2000x1200 mm hole in the table 1700x250 mm 500 mm Csdpfx Adordi Dlsdjhf column travel -side 820x650 mm total power requirement 45 kW weight of the machine ca. 44 t

Condition: reconditioned (used), Year of construction: 1983, Power: 2.000 kN Frequency: 60 rpm Codpfx Adogpxc Sodohf Stroke, adjustable: 20 - 120 mm Daylight: 450mm (max. stroke up) Ram adjustement: 100mm Size of bolster: 850 x 810mm Opening in bolster: 00 x 50mm Ram area: 750 x 810mm Motor power: 22 kW equipped by: - 1pc. con rod - 6pc. guideways - hydraulic overload - motorized oil lubrication - motorized ram adjustment - manuel stroke adjustment - pneumatic ram balancing cylinder - anti vibration machine feet

Year of construction: 1977, condition: used, Weiler Matador VS2 lathe year ca.1977 with collets , collet tube , three-jaw chuck , Multifix. Guide in the front area shrunk. Machine in a ready to use condition , After consultation under power ready for demonstration. Chjdpsmdn Dxjfx Addof

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz Chjdpfxohlnzko Addsf - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: excellent (used), Year of construction: 1983, Force: 45 tons Daylight: 205/305mm Table: 700x450mm Codpegfvnnofx Addohf Ram: 700x360mm Ram adjustment: 50mm Stroke: 10 - 50mm Strokes per minute: 80-400 Requested power: 11 kW Weight: 7.200 kos. Height: 3.100mm

Condition: excellent (used), Year of construction: 2005, operating hours: 3,320 h, functionality: fully functional, machine/vehicle number: 013, pressing force: 115 t, metric thread diameter (min.): 6 mm, metric thread diameter (max.): 10 mm, The machine is minimally used (3320 hrs) and in very good used condition. It has only been used to produce a small amount of stainless-steel flange nuts and washers. A wire heating device in front of the machine is also available. For full specification please send e-mail. Chjdpfx Aswbq Ihjddef SPECIFICATIONS: NO. OF FORGING STATIONS:5 CUT-OFF DIAMETER (MAX.): 17mm CUT-OFF LENGTH (MAX.): 17mm KICK-OUT LENGTH (MAX.): 20mm PUNCH KICK-OUT LENGTH (MAX.): 10 CUT-OFF QUILL (DIA X LENGTH): 55x68mm MAIN DIE (DIA X LENGTH): 75x80 DIE PITCH: 87mm PUNCH HOLE (DIA X LENGTH):55x120 RAM STROKE:110mm FORGING POWER:115 tons PRODUCT SIZE:3/8", 10mm OUTPUT (MAX.): 180 pcs/min POWER: 380V 3-PHASE, 50Hz, 125A WEIGHT: ~16 tons

Condition: good (used), Year of construction: 1993, - TRAUB control TX 8F - spindle passage 42 mm - Working spindle speed: 40 - 4.000 1/min - 4 grooving slides: stroke 60 mm - 8-fold turret - high pressure pump 25 bar - backworking (2 spindles) - bar feeder (3 m) - chip conveyor Chedpfx Aeldd Iqsddof