TOMRA TITECH X-ray sorting machine

TOMRA X-TRACT

Condition: excellent (used), X-ray sorting system. Manufacturer: TITECH TOMRA Model: X-TRACT 1200 Year: 2012 The machine is in very good condition. Complete machine overhaul carried out. Source renewed: €35,000 All sensors replaced: €29,000 Belt replaced. Areas of application: - Metal sorting - Sorting of wood, production of refuse-derived fuels (RDF) - Sorting of organic waste Csdpfxey Ra D Ro Aiaegu

Condition: good (used), functionality: fully functional, “Steinert NES 100 220 E 5009” for Sale Manufacturer: Steinert Cgodpfx Ajxb S Srsiasu Type: NES 100 220 E 5009 Belt widthness: 1.000 mm (New belt) With new control-unit. Overhauled, balanced, sandblasted and painted.

Condition: new, Year of construction: 2025, Features: - Overband Neodymium Magnetic Separator - HP - Dust suppression - Conveyor belt speed control - Self-propelled chassis for semi-trailer Cjdpjw Elbdsfx Aiasgu

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Cjdovf E Avepfx Aiaegu Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 2010, condition: good (used), 2 SICON shredders Csdjiz Tm Iepfx Aiasgu Year 2010 The electrical cabinet is missing Price 15 000€ each 4 densimetric tables : 8 000€ each

Condition: good (used), Technical condition: good Visual appearance: good Cedpfx Aot Dlursiajgu Please contact Ferdinand Pater for more information

Condition: refurbished (used), Year of construction: 2023, operating hours: 800 h, functionality: fully functional, Features: - Cutting unit Cgjdpfx Aew Elm Tsiaeu - Side wall extension in cutting area +300mm (one-piece) - Flat base plate on crawler chassis - Dust suppression - Engine compartment fire extinguishing unit

Condition: excellent (used), Year of construction: 2010, operating hours: 2,000 h, functionality: fully functional, machine/vehicle number: 093, overall weight: 30,000 kg, transport width: 2,500 mm, Doppstadt AK630 with very few operating hours. Used as a demonstration machine. Cgjdpfjwx Schox Aiaju

Condition: ready for operation (used), Drum Screen Terra Select. 50 mm screen perforation Cgodpevnmcvjfx Aiaju

Condition: good (used), functionality: fully functional, overall weight: 4,250 kg, “Steinert UME 110 120 P” for Sale Manufacturer: Steinert Type: UME 110 120 P Csdpou S R Ekefx Aiaegu 6,3 kW / 66,9 A. / 94 V. 100% ED Magnet L x W: 1.206 x 1.150mm Conveyor Belt: 1.200mm (new) AA.: Ca. 2.100mm Weight: 4,25 Tons With new transformer rectifier of 380V. Primary.