Clamping plate with T slot

unbekannt 2545/1515/H835 mm

Condition: used, length:1800 mm Bedpjcxxu Defx Ak Howl width:1200 mm weight of the machine ca.:1,6 t dimensions of the machine ca.:1,8 x 1,2 x 0,4 m

Condition: used, Clamping plate, marking-out plate, measuring plate, measuring table, welding table, welding table, straightening plate -Clamping plate comes: from a measuring machine -Width: 1335mm -Length: 3000mm -Height: 250mm Bwsdpfxjfc T Tqe Ak Hel -Plate thickness: 40 mm -Plate is with: support ribs -with: 4x adjustable feet -Number: 1 piece available -Transport dimensions: 3000/1335/H750 mm -Weight: 2749 kg

Condition: used, Miter cold circular saw KALTENBACH type KKS 400 NA Machine. No. 101701 Year of construction 1983 saw blade diameter 400 mm cutting range at 90° round Ø 130 mm sawing range at 90° square 120 x 120 mm sawing range at 90° rectangle 305 x 20 mm Cutting range at 45° round Ø 130 mm Sawing area at 45° square 110 x 110 mm Cutting range at 45° rectangle 245 x 30 mm Clamping range of collet feed 30 to 140 mm Working height 1000 mm miter cut 0 - 180 feed path 600 mm Saw blade speed 10 + 20 m/min. 2 steps Bodped N H A Nefx Ak Hewl motor power 1,7 and 2,6 kW hydraulic motor 1,5 kW Mains connection 380 Volt, 50 Hz - Hydraulic material clamp feed with infeed roller conveyor left 1500 mm - Feed path via double feed up to 1200 mm (2x feed, then sawing) - Hydraulic material clamping with vertical clamping cylinder - miter cut - saw angle with manual adjustment - hydraulic feed control, cutting speed manually adjustable - 2 motor speeds for the saw blade speed - saw blade stroke steplessly adjustable - coolant unit with electric pump in the machine base - Hydraulic unit fixed to the basic machine - Parts counter with zero cut-off space requirement of the saw 2600 x 1200 x 1900 mm weight of the saw approx. 1400 kg good condition

Condition: used, Aufspannplatte - Tisch einer Langhobelmaschine - Tischbreite/Aufspannbreite: 1845 Tischlaenge/Aufspannlaenge: 5505 mm 7 T-Nuten laengs fuer T-Nutensteine: M 30 T-Nutenabstaende zueinander: 263 mm Gesamtlaenge: 6230 mm Bwodpfxobn Amfs Ak Hol Plattenhoehe insgesamt: 350 mm Gewicht: 11 t

Year of construction: 1993, condition: good (used), machine/vehicle number: 03.2370, Arthur Klink - internal broaching machine (WAG 748) machine type: internal vertical hydraulic broaching machine manufacturer: Arthur Klink type: RISZ 10 x 1000 built in: 1993 stroke: 1000mm pulling force: 10.000KG working stations: 3 PCs drive: hydraulic system equipment: coolant system, magnetic chip conveyer remark: machine under power in stock the machine has an automatic workpiece loading system for 2 workpieces, ideal useable for high production Bwodpfx Aocc D Ddok Hel Optional accessories available on request: tools, workpiece holder Information about us: we are specialized for second hand broaching machine and still have anytime about 80 pcs of used broaching machines in our stock, vertical and horizontal machines from 3000kg up 63.000kg pulling force and from 1000mm stroke up to 3500mm stroke.

Year of construction: 1999, condition: used, CAPACITY 2000kgr Bwodpfowa I A Tjx Ak Hel HEIGHT 4.7M & 5M ARM LENGTH 3.2M 2 PIECES

Condition: new, functionality: fully functional, power: 18.5 kW (25.15 HP), fuel type: diesel, color: blue, operation weight: 3,375 kg, Year of construction: 2025, New RIPPA R 32 Pro mini excavator, Japanese Kubota engine, 4 cylinders, 18.5 kw, Euro 5 emission, Tier 4 Stage V, picker installation, air conditioning, mansalier camera, year of manufacture 2025, quick coupler, 1000 mm slope bucket, warranty. Bwodpfxowlvzuj Ak Hsl

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. Bjdpfx Aovf E Avok Hswl All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Year of construction: 1996, condition: good (used), machine/vehicle number: xxxx, High performance - bench tapping machines on T-slot plate Technical data: - Tapping capacity approx. M 3 - M 16 - Speed range up to 500 rpm Bjdpfxef Tcy Ds Ak Hjwl - Working range ( swivel radius ) 2500 mm - Quick-change tool holder size 2 diam.31 - various inserts for quick-change tool holder - Table surface with 5 T-slots 2050 x 900 mm . table height 910 mm - Machine vice with jaw width 200 mm - 3 jaw chucks 250 mm - pneumatic connection with pressure reducer - mobile underframe - space requirement approx. W 2400 x H 2000 x D 1000 mm - weight approx. 1100 kg

Condition: like new (used), Year of construction: 2000, operating hours: 25,000 h, travel distance X-axis: 10,300 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 1,800 mm, feed rate X-axis: 10 m/min, feed rate Y-axis: 10 m/min, feed rate Z-axis: 10 m/min, position of the milling head: 2.5 x 2.5 °, spindle speed (max.): 3,000 rpm, spindle speed (min.): 60 rpm, table width: 3,300 mm, table length: 12,000 mm, mount diameter: 50 mm, total height: 48,750 mm, total width: 1,00,000 mm, total length: 2,12,000 mm, overall weight: 1,00,000 kg, Duplex milling are two machines located one opposite the other which can work seperately or as single machine, workpiece can be machined with 2 simultaneous spindles. Production increase of up to 50% in relation to conventional solutions, i.e. individual milling machines Improvements in part precision, by managing to do the machining of the part in one single setup, in most of the cases One sole operator can control the DUPLEX milling machines Reduced space and investment requirement comparing with two single machines Fast investment amortization due to the high productivity Duplex solution admits different configurations: single working area, pendulum working areas For machining excavator arms / boom like, CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo X-Axis: 10300mm Y-Axis: 2000mm Z-Axis: 1800mm Table Length: 12000mm Table Width: 3300mm Table load: 100000 Power on spindle: 22/30kW Bsdpfx Akjrx Rxts Howl Spindle speeds: 60 - 3000Rpm Spindle Taper: 50ISO/Bt/Mk Feed rate X-Axis: 10000mm/min. Feed rate Y-Axis: 10000mm/min. Feed rate Z-Axis: 10000mm/min. Millinghead auto-index:2.5 x 2.5° Working hours: 25000H Length: 21200mm Width: 10000mm Height: 4875mm Weight: 100000kg