Debarking machine - spare part

Valon Kone VK 26

Condition: reconditioned (used), B., VK26M (1974 series) with motorized discharge table: - Main engine - Feeding table ( driven ) - Output table - Control cabinet Including infeed and outfeed table, workshop inspected * - debarking capacity: 10cm - 61cm diameter - 4 main decision makers - 4 cutting blades - Rotor speed =235 rpm / min - Rotor öppning=65cm - 30 KW motor, speed 1500/ min - Speed: 17-42m / min - 3m or longer ( length of wood ) Dimension ( without infeed and outfeed table ) L= 9840mm Entry table: 3540mm x 1000mm x 1900 Main engine VK26M : 2530mm x 2200mm x 2350 Outfeed table ( motorized table ) : 3170mm x 1000mm x 1300 RENOVATION: Item 1 1 Content: Disassembly of machinery, washing, sandblasting, priming and painting, repair, assembly Pos 2 1 Material of blade shafts on rotor new bearings and sealing (if necessary) Item 3 5 5 Other material: Piece V-belt for rotor drive Pos 4 1 Gear oil Pos 5 1 Material: Abrasive + Colours Pos 6 4 Valonkone piece peeling knife Pos 7 4 Valonkone piece Pre-separator Kodpfxofn Iu Ie Aayslr Pos 8 1 Switch cabinet : with 3-phase delta-start for 30 kw main motor with 3-phase delta start for 11 kW geared motor with start for 4 kw gear motor supply with start for 4 kw gear motor output Main Starter Emergency STOP

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Klsdpfjwp Rqfjx Aayor Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: reconditioned (used), Year of construction: 1974, Valonkone VK26M (1974 series) with outfeed table: - Main machine - Feeding table ( driven ) - outfeed table - switch cabinet IMMEDIATELY available from stock Including infeed and outfeed table, workshop inspected * - Debarking capacity: 10cm - 61cm diameter - 4 main cutters - 4 cutting knives - Rotor speed =235 rpm / min - Rotor opening = 65cm - 30 KW motor, speed 1500/ min - Speed: 17-42m / min - 3m or longer ( wood length ) Dimension ( without infeed and outfeed table ) L= 9840mm infeed table: 3540mm x 1000mm x 1900 Main machine VK26M : 2530mm x 2200mm x 2350 Outfeed table ( motorized table ) : 3170mm x 1000mm x 1300 RENOVATION: Pos 1 1 Content: Machine disassembly, washing, sandblasting, priming and painting, repair, assembly Pos 2 1 Material blade axles on rotor new bearings and sealing (if necessary) Item 3 5 5 Other material: piece of V-belt for rotor drive Item 4 1 Gear oil Item 5 1 Material: Abrasive + paints Item 6 4 Valonkone piece peeling blade Item 7 4 Valonkone piece Pre-separator Pos 8 1 Switch cabinet : Klsdetwrp Dspfx Aayor with 3-phase delta start for 30 kw main motor with 3-phase delta start for 11 kw geared motor with start for 4 kw geared motor infeed with start for 4 kw geared motor output Main starter Emergency STOP

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Ksdpfsu Hmacjx Aayolr Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted

Condition: good (used), Year of construction: 1994, functionality: fully functional, power: 75 kW (101.97 HP), Low-speed rotor with push floor Rotor width 2500 mm Kledetgqlyjpfx Aaysr Rotor diameter approx. 400 mm Motor 75 kw Discharge via conveyor belt with magnetic roller

Condition: used, Valon Kone VK26M With infeed and outfeed conveyors. Kljdevgtz Nepfx Aaysr

Condition: ready for operation (used), Slab recovery line with below machines: Kledpfx Aogwqk Ssayer One 2-blade board edger One single blade horisontal resaw Conveyors system between the machines included.

Condition: good (used), Year of construction: 1994, 2 side planer top - bottom constant table ( always same infeed height ) max. planing width 600 mm max. planing height 280 mm Ksdpfxehuthyo Aayslr planing shafts with strip knives immediately ready for use

Year of construction: 2006, condition: like new (used), Pneumatic crushing and sizing machine for band saw blades. Kodpsdy A A Nsfx Aayjlr

Condition: used, Speed: 0 - 80 m/min, Heads: 7, Kedpogrizvjfx Aayolr Planing height: 100 mm, Description: With electric box and hydraulic station. Planer Waco HM200X is used for longitudinal processing of solid wood, which results in such products as MDF panels, plastics or similar types of materials. The Waco HM200X has thirteen different stations that can be adapted to different planing modes. In addition to standard equipment such as feeders, top and bottom cutters, side cutters, the machine also has starting blocks, auxiliary feeders, flat cutters, a bevel side cutter, a cutter block and a universal cutter. The maximum working width is 200 mm and the working height is 100 mm. The feed speed can be set in a stepless range from 0-40 or 0-80 m / min. The feeder is equipped with three upper and three lower drive rollers.