Gas-heated bogie hearth drying oven

VEI-Engineering VEI_HO_GB

Condition: used, functionality: fully functional, Used Schenck Balancing Machine H 50 V/B with used CAB 690 H measuring unit. (Can be upgraded to a new CAB 920 unit for an additional (18 000–20 000€) The machine comes with original foundation drawings, documentation and manuals. The machine can be test run in Kerava. Rotor Capacity - Rotor weight range: 20 – 6 000 kg Kodpex Ein Sefx Aayodk - Maximum symmetrical load on pedestal bearing: 7 500 kg - Maximum symmetrical load on stand bearing: 3 750 kg - The machine can be loaded freely with lower weights when following recommended procedures. - Maximum rotor length between pedestals:1 600 mm (belt drive) - Maximum diameter over machine base: 2 100 mm - Clamped rotor diameter ranges: 25–180 mm, 180–380 mm - Machine bed length: 3 500 mm - Balancing speed n depends on the rotor’s moment and must be selected to avoid overloading the drive. - Maximum permissible G·n² value: 1400 × 10⁶ kg/min² - Applies to a rigid symmetrical rotor mounted on pedestal bearings. - May be exceeded during dynamic tests on flexible rotors and strength tests. - End drive / FU motor: 7,5 kW - 4-speed gearbox: 120–2520 rpm - Belt drive BU 5 / FU: 7,5 kW - Unbalance Umar 0,5 gmm/kg: 0 gmm/plane

Condition: good (used), Plant: REWA Chamber Filter Press used Type: 470-15-25K-HP Design: side rail guided Filter plate format: 470x470 mm Number of plates: 15 Filter plates: PP Filter cloths: optionally available in coordination with the medium Press capacity: approx. 57 dm3 Kodpfx Aeqakbrjaysdk Filter pressure: approx. 15 bar Material of parts in contact with the product: Flange, feed-throughs stainless steel, PP or rubberized Material of parts not in contact with the product: Stainless steel Purchase or hire: Inspections of the systems by arrangement at our factory. Other: We can supply you with used equipment ready for operation or refurbished according to your wishes and requirements. Would you like to rent or buy this system? Please contact us, we are at your disposal.

Condition: new, TECHNICAL DATA Kdodpfsg Dgymjx Aaysk type: gas-heated drive-through chamber furnace internal dimensions: (w x h x d): 2200 x 2350 x 3000 mm number of control areas: 2 Max. loading weight: approx. 2,5 t PLC: Siemens S7

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm 650x450 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,9 x 2,87 x 1,3 m PROMOTIONAL PRICE!!! Kedpfsd Iipmex Aayodk 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off 5. Raise the frame until it is just above the material 6. Vice opens

Condition: good (used), functionality: fully functional, Year of construction: 1990, machine/vehicle number: 4ROLL, roller (bottom) diameter: 470 mm, roller (top) diameter: 470 mm, side roll diameter: 420 mm, roller diameter: 470 mm, roller length: 3,050 mm, working width: 3,050 mm, working height: 1,800 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 45 mm, sheet thickness aluminum (max.): 45 mm, sheet thickness copper (max.): 45 mm, overall weight: 43,000 kg, total length: 7,700 mm, total width: 2,410 mm, total height: 2,470 mm, power: 37 kW (50.31 HP), input voltage: 380 V, type of input current: three-phase, working length: 3,050 mm, Equipment: documentation/manual, emergency stop, PLATE BENDING MACHINE FACCIN - 4 ROLL HYDRAULIC 3000 X 40 MM MODEL 4HCI3-35/30 YEAR 1990 PLATE BENDING ROLL LINEAR GUIDEWAYS DOUBLE PINCH PRE-BENDING Machine in good working condition Bending capacity -Plate width : 3000 mm -Rolling plate thickness 40 mm - Prebend thickness 35 mm Rolls dimensions: -Useful length 3050 mm -central rolls upper/lower 470 mm -side rolls left/right 420 mm • Hardening of the 4 rolls high strength surface • 3 rolls driven powered with gear unit with hydraulic motor • Conical bending attachment side rolls tiltable to form cones, contrast pad roller type. • Opening front hydraulic drop-end to unload the closed shell. Kjdpfx Aowb Scmeayodk • Variable speed working roll bending rotation hydraulic speed fast/slow. • Console electric on wheels with centralized commands joysticks and 3 digital readout. • Digital readouts of the rolls position bending and pre-bending repeatability. • Hydraulic tank capacity oil 350 liters – power electric 37 Kw voltage 380 /50 • Dimension 7700 x2410 x H 2470 mm - weight 43000kgs

Condition: refurbished (used), functionality: fully functional, Löser centerless tube grinding machine - belt grinding machine - polishing machine - Cylindrical grinding machine Centerless tube grinding / polishing machine for workpieces with a minimum length of 1100mm. The machine was built in 1988 and was completely overhauled in 2012. The machine was converted for polishing and then only polished around 10,000 parts. The machine was no longer used after that. During the general overhaul, the motors, bearings and the entire control cabinet with the frequency converters were completely replaced. The machine can be used for both wet grinding and polishing. Wastewater treatment including pumps is not yet available. We can retrofit these for you free of charge according to customer requirements. The transport systems (roller conveyors) between the grinding stations must also be retrofitted to suit your workpieces. The machine can process pipe diameters from 10mm to 160mm. The grinding motors / polishing motors have an output of 7,5kW per station. Kdedpfxopugwie Aayek The system can be viewed by appointment in our warehouse in D-63128 Dietzenbach.

Year of construction: 2006, condition: refurbished (used), HYDRAULIC PRESS MECAMAQ PRESSURE 350t STROKE 350mm TABLE LEFT RIGHT 600mm TABLE FRONT BACK 750mm POWER 15kw Dimensions: Height: 2,9m Width: 1,9m Length: 1,3m Weight: 5.700 kgr Kedpfefmqqlex Aaysdk

Condition: new, Year of construction: 2026, table length 4000 mm table width 2000 mm burner heads 1 Control CNC workpiece weight 2510 kg traversing speed 200 m/min dimensions of the machine ca. 11599 x 3380 x 2718 mm Laser cutting machine with automatic shuttle table Configuration 1. BodorPower laser source 12 kW 2. BodorGenius laser cutting head with autofocus 3. BodorThinker 3.0 control system 4. Bed made of tenon and mortise structure 5. Stretched aluminum portal 6. One-click fully automatic processing 7. Automatic layout of residual material 8. Edge detection and automatic zeroing of the focal length through intelligent detection 9. Bodor Lightning perforation technology 10. 21.5-inch monitor with touch function 11. Intelligent control of gas pressure 12. Automatic adjustment of cutting gas pressure 13. Bodor Mango® ergonomic remote control 14. Active anti-collision function 15. Intelligent vibration protection 16. Intelligent adjustment to overheating 17. Gas-saving nozzles with stable flow 18. Intelligent maintenance reminder 19. WIFI internet connection 20. Water cooling 21. Dust removal function 22. Safety light curtains 23. Extraction 24. Wear parts set CUTTING CAPACITY: STRUCTURAL STEEL 35 mm STAINLESS STEEL 35 mm Kdjdewh Ukyepfx Aayok ALUMINUM 20 mm

Condition: good (used), functionality: fully functional, Characteristics: Distance between centers: 4500 mm Turning diameter: max. 750 mm Spindl bore diameter: 105 mm Kdjdpsvy Adgofx Aayjk Control: Heidenhain Including 2 x chuck diameter 500 mm and 315 mm Including 2 x steady rest

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61037337, clamping force: 800 kN, screw diameter: 30 mm, displacement volume: 113 cm³, injection pressure: 2,500 bar, injection weight: 103 g, mold height (min.): 400 mm, ejector force: 22,600 N, ejector stroke: 150 mm, opening stroke: 900 mm, total length: 3,960 mm, total width: 1,480 mm, total height: 2,020 mm, overall weight: 3,550 kg, heating capacity: 10.9 kW (14.82 HP), drive type: Hadraulisch, clear span: 470 mm, tool weight: 10,00,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The fully hydraulic CX series offers a particularly compact, efficient and flexible two-platen machine. The very compact two-platen concept with cantilevered clamp offers generous space for peripheral equipment and excellent accessibility. Efficient and intelligent energy management with BluePower servo drive continues to provide a powerful basis for the highest demands and the right solution for every application. TECHNICAL DATA: KM 80 / 380 CX G06 (order 38655610) CONTROL  MC 6 with 21.5" TFT color screen with multi-touch functions CLAMPING UNIT  Clamping force kN 800  Mold opening force, max kN 55  Clear width (h x v) mm 470 x 420  Clamping platen (h x v) mm 670 x 670  Tool installation height min. - max. mm 400 (increased by 150 mm)  Opening width mm 900 (increased by 150 mm)  Mold opening stroke max. mm 500  Hydraulic ejector drive  Ejector stroke mm 150  Ejector force forwards/backwards kN 22.6 / 9.8  Ejector speed forwards/backwards mm/s 760 / 800  Max. Mold weight kg 1000 SPRING UNIT  Screw diameter / type mm 30 / standard (customization possible)  Effective Ls/D ratio 26.7  Injection pressure bar 2500  Stroke volume cm³ 113  Shot weight at max. stroke for PS g 103  Injection speed mm/s 100  Injection flow rate cm³/s 71  Screw drive/speed 1/min 295  Plasticizing flow (standard) g/s 12.3  Nozzle contact force kN 50 ELECTRICAL PARAMETERS Connected load kW 15.0  Installed heating capacity kW 10.9  Power supply V / Hz 380 / 50 3 phases with neutral conductor WEIGHT AND DIMENSIONS Ksdpfxjud N Hdj Aaysdk  Net weight with switch cabinet t 3.55  Length x width x height m 3.96 x 1.48 x 2.02 ADDITIONAL EQUIPMENT  Low-wear plasticizing  BluePower fully insulated plasticizing cylinder  Open nozzle  1 additional temperature control point for nozzle heating  Air valve 1 - compartment (BWAP)  Pneum. Control hot runner valve gate 1 - compartment  Hydraulic core pull 1 - compartment (BWAP)  Euromap interface handling E18, E63  Euromap interface (central computer) E67, E77  Adaptive Process Control (APC)  Injection stamping circuit  Graphic analysis package The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your inquiry.