Dividing head

Walter TANIH320EVO

Year of construction: 2002, condition: not inspected (used), Robot no control panel + connection cables Used, untested robot. No technical documentation available. Not tested. Fpjdpfx Asgu U Itep Djn

Condition: used, Year of construction: 2004, Technical details: x-travel: 1500 mm y-travel: 1000 mm z-travel: 1000 mm control for program: TNC 530 spindle hours: noch nicht bekannt h milling head speed: 1: 30 bis 930 und 2: 930 bis 4000 / steples U/min Fpjdpfsu Nc Riex Ap Den tool taper: horiz./vertical: SK 50 (DIN 69871/Din 69872 Form A) max. torque on the spindle: 1000 Nm spindle head swivable left - right: 90 ° feed: 1 - 6000 mm/min feed power: 30 kN kN rapid traverse: 15 m/min Number of tools: 1 St. table clamping surface LxW: 1600 x 800 mm table load: 40 kN kN voltage: 400 V / 50 HZ V total power requirement: 42 kW Weight approx.: 15,2 t compressed air: 6,3 bar dimension machine xH: 3,1 x 4,7 x 2,6 m dimensions: Kühlfilter: 1,9 x 1,6 x 1,4 mm space requirements approx. LxWxH: ca. 38,5 m² m² Applications: Milling, drilling; tapping, boring. with direct coded length measuring systems the guideways of the 3 axes are on flat guideways CTS and external cooling Milling head position controlled +/-90° milling spindle nominal drive power 22 kW with integrated hydraulic power unit up to 100bar operating pressure with coolant unit with filtration, with high pressure pump 60 bar (internal cooling), nominal delivery 20 l/min. and low pressure pump 4 bar (external cooling) as well as spray gun Hinged belt chip conveyor DGS, type SSF 600 P50 Accessories: Measuring probe SK40 Reference tool SK40 Milling head SEMPUCO *

Condition: excellent (used), Year of construction: 2006, • Configuration: 3 linear axes (X/Y/Z) + B-axis tilting head • Travels (X/Y/Z): 2,500 / 920 / 820 mm • Table: 3.100 × 900 mm · max load 3.000 kg • Spindle: 20–18.000 rpm · HSK-A63 · 35/25 kW • Rapids: X 100 m/min · Y/Z 60 m/min • Tool magazine: 120 tools Fpodpfxjy Skmrj Ap Den • Control: HEIDENHAIN iTNC 530 Brand new Spindle installed as end of April 2026

Condition: excellent (used), Year of construction: 2012, Control: Fanuc 0i-TD Equipment: Fpjdpfx Aey Dqb Tjp Don - various tool holders - various driven tools - C-axis, driven tools Max. turning diameter: Ø 500 mm Max. turning length: 600 mm Bar capacity: Ø 75.5 mm Spindle speed: 3500 rpm Spindle nose: A2 - 8 Machine weight: 6,700 kg

Condition: good (used), Year of construction: 1970, functionality: fully functional, Single Column Vertical Turning Lathe | Froriep DS 14 NC The machine was overhauled in 2009, recently cleaned, and is in good condition. Fpjdpfx Apoyft S Ae Djn - Table diameter: 1,400 mm - Swing diameter: 1,600 mm - Turning height: 1,500 mm - Siemens control type 840 D - Automatic tool changer - Workpiece weight: 6,500 kg - Vertical slide travel: 1,000 mm - Spindle speed: 10–315 rpm - Feed rate: 3,600 mm/min Inspection is possible at any time by prior arrangement. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: Froriep | DS14 | DS14NC

Condition: used, Technical details: turning diameter over bed: 3800 mm turning diameter over slide rest: 3200 mm turning length: 12000 mm Fpsdpfxox Ngzyj Ap Den faceplate turning speed range -stepless-: 2 - 200 U/min max. workpiece weight: 90.000 kg bed width: 4000 mm 2 steadies *

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Fpjdpjuz If Nefx Ap Den Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Year of construction: 1968, roll diameter 500 mm throat 1050 / 485 mm workpiece height 300 mm saw band length 3920 - 4050 mm cutting speed 15 - 940 m/min table height 1040 mm table surface area 750 x 800 mm Table tiltable 15 Grad total power requirement 4,0 kW weight of the machine ca. 1750 kg dimensions of the machine ca. 2100 x 1000 x 2100 mm - Unique mitering range left/right up to 30° acute angle - Mitering adjustment via lockable detent every 15° - Adjustable saw blade for optimum cutting angle - Hydraulic clamping device on both sides Fedpfoiqp Erjx Ap Depn - Electric blade breakage monitoring - Smooth-running saw carriage via preloaded recirculating ball bearings - Additional table 450 x 450 - Machine light

Condition: good (used), Year of construction: 2008, turning length: 12,000 mm, spindle motor power: 60,000 W, total height: 3,800 mm, total length: 23,000 mm, total width: 7,600 mm, swing diameter over cross slide: 1,520 mm, turning diameter over bed slide: 1,140 mm, workpiece weight (max.): 20,000 kg, overall weight: 58,000 kg, Equipment: documentation/manual, CNC Lathe Giuseppe Giana - GGH 1100/760 x 12.000 CNC MACH-ID 9439 Make: Giuseppe Giana Type: GGH 1100/760 x 12.000 CNC Control: Siemens 840 D-SL Year: 2008 3 bed way construction Bed width 1100 mm 3 x C-Type Steady rest on lower base with in feed 2 x Fixed steady rest 300 - 800 mm with 5 ton 2 x Chip conveyor 4 Chuck 1000 mm Fjdpoyl Uh Ssfx Ap Depn Barafuldi 4 way turret head Swing over bed Ø: 1520mm Swing over cross slide Ø:1140mm DBC Turning Length: 12000mm Spindle bore: 155mm Spindle power: 60kW Bed width: 1100mm Tailstock spindle Ø: 310Ø Stroke pinole: 300mm Spindle taper: 1:4 taperMk Workpiece weight: 20000 Power: 80A Speeds / ranges: 0-800Rpm Feed rate X-Axis: 0-8000mm/min. Feed rate Z-Axis: 0-8000mm/min. Length: 23000mm Width: 7600mm Height: 3800mm Weight: 58000kg

Condition: good (used), Manufacturer: STANKO Type: 7D430 Year of manufacture: 1994 Table rotation 360° Head tilting possible up to 10° Big cabinet with slotting key way tools Lubrication Completely overhauled in 1994 Specifications Fsdpfxewpud As Ap Djpn Metric US Standard Table diameter Ø 630 mm Table load 1000 Ram displacement 320 mm X - Axis 650 mm Y - Axis 510 mm Outreach 500 mm Number of strokes 3 - 38 m/min min. Power 12 kW Dimensions (estimated) Length 3000 mm Width 2200 mm Height 3000 mm Weight 6150 kg Please note: The information on this page was provided to the best of our knowledge and ability by us, and, where possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not constitute representation and contractual terms. We recommend that you verify all important details.