Single Column Eccentric Press

Weingarten ARP 100

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Rjdou Rwa Ispfx Adrst Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Rjdekvnumopfx Adrst Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1981, condition: ready for operation (used), There are two identical eccentric presses available, nominal force: 1000kN, stroke speed: 30-85/min, stroke adjustment: 20-125mm, weight: 8t, year of construction machine 1/ 2: 1978/ 1981, with documentation. Rsdslc N Rvjpfx Adrot

Condition: used, Year of construction: 1983, pressure 100 t throat 375 mm stroke 20-125 mm no. of strokes 60 Hub/min ram - range of adjustment 80 mm table surface area 920x660 mm Rodpjxh Swhofx Adrst ram surface 700x450 mm hole in the table Ø90 mm tool hole in ram Ø50 mm weight of the machine ca. 8 t dimensions of the machine ca. 2100x1500x3300 m

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, Rjdpfx Adjg U Utvorjt clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 Rodpfx Adehlnzkorjt - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: as good as new (ex-display), Year of construction: 2008, machine/vehicle number: LSP 100T, Productions-Hydraulic press with H-column 100t with guidance Rjdog Rn Efopfx Adrst Manufacturer: Stenhoj Denmark Year of construction: 2008 Pressure force max. 1,000 kN / 318bar Press cylinder, stroke length: 400mm Press table with T-slot 1,500x900mm above 1,500x1,050mm below Stand passage 1,700mm Condition as good as new, the machine was only used for test runs and has been in stock since then. All statements without guarantee. Without transport costs.

Year of construction: 2009, condition: used, material width 320 mm material thickness 8 mm no. of straightening rolls 9 Redpfx Aop U Uwiodrjt material cross-cut 2000 mm² weight of the machine ca. 4,2 t dimensions of the machine ca. 2000x2000x2400 mm

Condition: new, Year of construction: 2025, Band width: max. 38 mm Feed length: max. 50 mm Rjde Ea U Hepfx Adret Band thickness: 0.05...1.02 mm Stroke rate: max. 260 rpm at full feed length Feed force: 90 N Optionally with mechanical control valve or optionally with electric valve (24V or 230V) Many other band widths and feed lengths available.

Condition: used, Year of construction: 2021, machine/vehicle number: HB 2022-A-073, pressing force: 300 t, Portal straightening press with 300 T capacity a) idle and pressing speed up to 17 mm/sec. b) opening speed up to 55 mm/sec c) table size 2500x1600mm d) open height 700 mm e) total size approx. LBH 4500 x 2300 x 3700 mm f) Oil temperature indicator on the tank g) Lubrication via grease nipple h) table in grid construction,with T grooves according to customer's request, otherwise 22mm i) operation on swivel arm, mounted on the bridge j) pressure adjustment from 50 T to 300 T via MONITOR k) bridge moves by two gear motors, via racks l) Cylinder moves to the left and to the right via toothed racks m) Machine body double painted n) Cylinder induction hardened Type of construction Press design PORTAL PRESS Thermally neutral 80 - 120 °C Number of operating sides 3 side Redpfxoh Agnuj Adret Forces Pressing force max. 3,000 kN Free ripping force max. 500 kN Pressure build-up time Closed die Steel to steel Max. 3 sec. Dimensions Max. Opening width 700 mm Stroke and min. opening 700 mm/ 0 mm Table height above floor approx. 9ß0 mm Height above floor (headroom) approx. 3700 mm Hall height min. 5.000 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.8 mm/m Weight Total weight of press without operating materials and table plate approx. 22 T Speeds Fast closing with 17 mm sec. Pressing speed 8 mm sec. Opening 55 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel after max. 78 db(A) DIN 45635-T16-KL3 Hydraulics Number of pressing cylinders 1 pc. Operating pressure max. 350 bar Pressing pressure build-up time 02. mz sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH approx. 93 L/min Oil volume approx. HLPD 46 MW 900 liters Ambient temperature max. 45 °C Oil temperature max. 55 °C Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Hydraulic connection Main motor IE3 22 kW Total connection Approx. 30 kW