Sharpening machine

WEINIG Rondamat 909

Condition: new, Year of construction: 2025, New Knife grinder with tilting magnet mm 1200 long, carriage speed steplessly variable, automatic downfeed of the grinding wheel, adjustable grinding length, PLC, colour touch screen display, coolant system Nodpfx Aowamkvjlhecu

Condition: excellent (used), Year of construction: 2021, operating hours: 9,500 h, functionality: fully functional, machine/vehicle number: 3284, Standard version of RUF Lignum R2 with outfeed channels, el.motor 22 kW, briquette sizes 150x60 mm capacity up 500 kg/h Ncjdeyyl Srspfx Alhsu

Condition: excellent (used), WEINIG Hydromat H23 Line, S/N 87321, year 1999, Ref-No. 103437 WEINIG Cross Conveyor HighMech E-1, equipped with 6 flat chains approx. 2000 x 3500 mm Hydraulic WEINIG Accelerator Model 814 Short infeed table with heavy-duty 4-roller feed unit Planer/moulder with reinforced KASCHWIG three-sided soundproof enclosure • Max. working width: 230 mm • Max. working height: 160 mm • Electronic feed, frequency-controlled, 8–80 m/min • Feed motor 18.5 kW • 1st spindle bottom 11.0 kW • 2nd spindle right 11.0 kW • 3rd spindle left 11.0 kW • 4th spindle right 11.0 kW • 5th spindle left 11.0 kW • 6th spindle top 15.0 kW • 7th spindle bottom 11.0 kW • 8th spindle top 15.0 kW • 9th spindle bottom 15.0 kW • 10th universal spindle 11.0 kW (four-sided) • Spindle speed 6,000 rpm • Spindle diameter ø 50 mm • All spindle motors equipped with NEW motor start/stop brake units • Pneumatically supported top pressure rollers • Feed rollers D=140 mm • 6 driven rollers in the table • Spindles 1 + 6 + 7 + 8 + 9 with counter bearings • Spindles 8 + 9 with straight jointer • Spindles 8 + 9 with profile jointer • Spindles 6 + 8 with pneumatic pressure • Reduced spacing between feed rollers • Hard-chromed table plates • Hard-chromed fences • Pneumatically supported side pressure rollers • Automatic table lubrication • Centralized lubrication points • Free-standing control panel • Connected load approx. 145 kW / approx. 400 A • Free-standing electrical cabinet • Operating instructions, spare parts list and wiring diagram included • Machine sold without cutterheads Machine dimensions approx.: • Length: 6,000 mm • Width: 2,250 mm • Height: 1,800 mm • Weight: approx. 8,500 kg Nodpfewvqkljx Alhscu Factory-new WEINIG components installed: NEW horizontal/vertical spindle NEW counter bearings All spindles with HL bearings All motors newly fitted NEW electronic motor soft start/brake devices NEW hard-chromed table plates NEW hard-chromed fences Many other new parts fitted in the machine Condition: see attached photos – technically in excellent condition Infeed mechanization unrefurbished – complete – fully functional Payment: Net cash before loading Delivery time: By arrangement Delivery: EXW Inspection: Anytime by appointment Errors and prior sale excepted.

Condition: used, No. 3176 Automatic planer and moulder WEINIG Hydromat 1000 Used, year of construction 2007 6 spindles: bottom-right-left-top-top-bottom Electronic feed 6 - 60 m/min Working width 80 - 150 mm Working height 23 - 65 mm Finished slat widths 4 - 15 mm Max. Max. number of slats 16 pieces Nedpfju Agh Sex Alhscu Slat lengths 400 - 4000 mm 1st spindle horizontal at the bottom Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool flight circle 125 - 180 mm 2nd spindle vertical right Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm 3. spindle vertical left 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm Pressure shoe in front of the spindle, swiveling away, pneumatic roller contact pressure 4. spindle horizontal top 15 kW, 6000 rpm, diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 5. horizontal top spindle as saw spindle Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment travel reduced to 25 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 6. horizontal spindle at the bottom as saw spindle Brake motor 30 kW, 5000 rpm Axial adjustment travel reduced to 25 mm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm All moulder spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of the feed rollers compared to the left-hand spindle, axial 35 mm Shorter roller distance compared to the right-hand spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in the table, lateral pressure roller Automatic waxilite pump / lubricant pump Machine with 4-roller extension, pendulum shafts extended to 200 mm 2 driven, toothed rollers in the outfeed table 2 driven, toothed rollers in the machine table Pressure beam before and after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electrical height adjustment of the upper spindles and the feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transportation and assembly Subject to errors in the description and price Transportation and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood Nedjv Si Szepfx Alhocu The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) 22” color monitor, IBM computer, printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Functional description: 1. filling the autoclave with wood 2. creating a pre-vacuum 3. filling with gas 4. heating 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: excellent (used), Year of construction: 2014, Viesmann Vitoplex 100 LS with Weishaupt WM - G10/4A Nedpjtrl Sksfx Alhjcu

Condition: like new (used), Year of construction: 2024, Used double-sided cantilever racking: hot-dip galvanized bolted system Scope of supply: 4 double-sided racking uprights, height 4,160 mm with base section 1,200 mm 24 cantilever arms with 1,200 mm depth, standard Including longitudinal and diagonal bracing for 1,300 mm center distance Incl. fastening material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Spare parts can be reordered and expansion is possible at any time) - (*Also available in larger quantities: 20 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per upright side 2,250 kg - Load capacity per cantilever arm 750 kg - Cantilever arms height-adjustable in 100 mm increments - Per upright, 6 screwable cantilever arms and 2 base sections with a depth of 1,200 mm, standard = 4 storage levels on top of each other per upright side - Including longitudinal and diagonal bracing for 1,300 mm distance - Racking length 4,000 mm - Including fastening material (without floor anchors) - With assembly instructions and load signs C4 according to DIN standard - Telephone technical advice - Made in Germany - Short delivery time - On-site collection possible Our cantilever racking is produced exclusively in Germany. We offer reliable freight services with prior notification before delivery. The material is packed in a way that allows for easy unloading. When installed outdoors, the load capacities are reduced by the wind and snow load. Ncsdpfx Ash Ek Daelheu The subsoil must be made of concrete, level and suitable for dowels, and must be able to absorb the acting loads. The customer must check and ensure the ground conditions, load-bearing capacity, and any required official permits. The racking uprights must be anchored in the ground on site; anchoring to the wall is not necessary and is not recommended. According to the occupational health and safety association, it is recommended that the racking uprights have a minimum overhang of 500 mm to the top edge of the upright on the uppermost storage level.

Condition: used, Year of construction: 1996, Vollmer CHC 260 Njdpfx Aeyuc Ifjlhocu Year of manufacture: 1996

Condition: new, Year of construction: 2024, functionality: fully functional, power: 5 kW (6.80 HP), cutting height (max.): 200 mm, cutting width (max.): 1,300 mm, saw blade diameter: 550 mm, cutting length (max.): 3,200 mm, cutting width at rip fence: 1,300 mm, sliding table length: 3,200 mm, Exhibition machine F 45 Elmo Drive Nedpfouh R R Esx Alhscu - Swivel + / - 45 ° - Cutting height 200 mm - Preparation for scoring unit no. M24038 - Double roller carriage with 3200 mm - Angular mitre fence 3200 mm Digit L - CNC rip fence 1300 mm - Duplex mitre fence 1350 mm manual - Template holder - On/Off switch on the double roller carriage - Front support roller

Condition: used, Year of construction: 2006, total width: 4,600 mm, total height: 1,830 mm, Dimensions (LxBxH): 217 x 460 x 183 cm Price: On request - Year: 2006 - Documentation available: No - CE marking present: Yes - CE certificate present: No Nedpfxewnig Ns Alhecu - Serial number: 107402 - Number of spindles [pcs.]: 4 - └ Spindle 1: - - Spindle diameter [mm]: 40 - └ Spindle 2: - - Spindle diameter [mm]: 40 - └ Spindle 3: - - Spindle diameter [mm]: 40 - └ Spindle 4: - - Spindle diameter [mm]: 40 - Feed table length [mm]: 1780 - Feed motor [kW]: 5.2 - Conveyor drive: Cardan drive - Diameter extraction nozzle [mm]: 140 - Voltage [V]: 400 - Transport dimensions: 2170mm x 4600mm x 1830mm (l x w x h) - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels