WRC 1225 AC Horizontal Band Saw

WRAVOR WRC1225 AC

Condition: excellent (used), Year of construction: 2020, Machine in very good condition, low hours – fully equipped. Crsdpfx Aew E Ei Uoddjk Additionally, 20 saw blades included in the set. SPECIFICATION: WRAVOR BAND SAWMILL Type 1225 AC (tilting edge cutting) Max. log width: 1250/1090 mm Max. cutting length: 8 m Main motor: 45 kW Cast wheels Wheel width: 130 mm Wheel diameter: 1200 mm Lift up/down – double screw TR60x9 (18) + 11 kW Danfoss inverter + Siemens 3-phase motor with brake Electric lifting/lowering motor: 11 kW Saw blade PV 45, length 8685 mm, thickness 1.2 mm, width 140/150 mm Feed drive with electronic controls: forward/reverse feed, SEW gearbox with flat asynchronous controller KA87 / GDRL100L 4BE5 / TF / ES7S / V Manual-sensor thickness adjustment with electric disengagement Digital thickness adjustment with Wravor V280 program Hydraulic unit 40 l, tank with two pumps 13+6 l, 3 kW motor Complete hydraulic system Hydraulic blade guide, left and right (linear HIWIN) Hydraulic debarker / bark cutter: 1 Hydraulic board ejector: 1 Additional hydraulic board ejector and guide Side-mounted control panel Multifunction joystick with 2 positions: 1 Multifunction joystick with 4 positions: 1 Laser 15 mW: 1 Cameras: 3 Fan 2.2 kW + 15 m sawdust pipe + 4 brackets for pipe Water cooling – automatic hydrofor cooling system (Aki Tech high-pressure pump): 1 Preparation for ramp and automatic table + spreader: 1 Diesel lubrication system: 1 TRACK Welded frame, 14 m long Hydraulic clamp with two cylinders: 6 Hydraulic cant flipper: 6 Mechanical supports: 2 Hydraulic roller – forward: 6 Hydraulic log lifter with mechanical rollers: 4 Hydraulic log lifter with hydraulic rollers: 7 Set of lifting rollers: 7 hyd. + 4 m, 1 pc Hydraulic turner – new type: 3 Centering device – 1 set: 4 Hydraulic unit 120 l, tank with single pump 50 l, 15 kW motor + Danfoss inverter: 1 Cable carrier with energy chain: 14.5 m C-profile cable tray for ventilation – 4 double trolleys 4 m belt output conveyor with 1 m feed + 3 kW electric motor, front section with hydraulic lift

Condition: used, Year of construction: 2006, Manufacturer: Weinig Model: Unimat Super 4 Year of manufacture: 2006 Four side planer Manufacturer: WEINIG restored Model: UNIMAT SUPER 4 with mechanization of short workpieces EM15 - Year of manufacture: 2006 Technical specifications - Working width: max 150 mm - Working width: min 25 mm - Working height: max 50 mm - Working height: min 15 mm - Number of spindles: 3 - Power top spindle: 22 kW - Power bottom spindle: 11 kW - Spindle rotation speed: max 1/min 7.000 rpm - Spindle diamete: 40 mm - Table length: 2.000 mm - Feedrate max: 24 m/min - Continuously variable feed - Seperate motor per spindle - Roller infeed Cardanic drive - Infeed from magazine - Motoric adjustment Planing height - Lubrication pump automatic Csdpfjqprk Tsx Addork - WEINIG Face-milling cutter - WEINIG EM 15 - Total connection: 45 kW

Year of construction: 2010, condition: excellent (used), functionality: fully functional, The following machines, all in very good condition, are available for sale – perfectly suited for professional use in the wood processing industry. Saw line consisting of: • Feed unit ZV21, model EV 50 • Profiling chipper ZD31, model VM50 Crjdpfow Stiusx Addsk • Outfeed unit AV31, model VZM • Centering device VZ21, model VZV • Log rotation device DV21, model DV70-2 • Infeed and centering unit EVP • Profi Chipper VM50 • Profiling unit VMP450 F61 (4x110kW) • Microtec measuring system Additionally available Other used woodworking machines ?️ Also available: Additional used woodworking machinery Log infeed Springer  • 5-arm design  • Log distributor (5-arm)  • Receiving tipple transfer (26 m) Log rotation device LINCK DV35/DV1 (new)  • Dimensions: 2.0 m (L) x 2.4 m (W) x 2.5 m (H)  • Weight: approx. 1.5 t  • State-of-the-art rotation technology for precise positioning 2 units chipper infeed – infeed and centering unit EV30  • Dimensions: 5.5 m x 2.2 m x 2.1 m  • Weight: 8 t each Separator conveyor  • Dimensions: 8.6 m x 2.0 m x 2.6 m  • Weight: 7 t 2 units LINCK chipper V30 (incl. spare chipper discs)  • Dimensions: 5.5 m x 2.3 m  • Weight: 11 t each Saw VS 66 – left & right side  • Dimensions: 2.8 m x 2.1 m x 2.5 m (each)  • Weight: 3 t each LINCK pre-centering unit  • Dimensions: 3.0 m x 2.0 m x 1.1 m  • Weight: 0.8 t Log infeed with loader and log conveyor Location & Availability All machines are located at our warehouse, A-3525 Lugendorf No. 38, and are available immediately. Price upon request For further information or to arrange a viewing appointment, please do not hesitate to contact me.

Condition: new, Year of construction: 2024, MULTIPLE RIP SAW ANGOMAC MAX DEPTH OF CUT 120 MM Max. width of cut 480 mm Max. passage width 600 mm Codpfx Adsh Ia Upjderk

Condition: good (used), Four side planer Weinig Unimat 23 Lamelling machine 9 spindles, grooved bed Working width: 230 mm, Cedopq T Rbopfx Addjrk working height: 170 mm, spindle diameter: 40 mm, feed: 5,5 kW / 6 - 36 m/min, spindle arrangement: 1- Down ( 5,5 kW ) 2- Right ( 5,5 kW ) 3- Left ( 5,5 kW ) 4- Right ( 5,5 kW ) 5-Top (11 kW) 6-Bottom (5,5 kW) 7-Top (7,5 kW) 8-Bottom (37 kW) 9-Uni (11 kW) 5 driven rollers in the table

Year of construction: 2019, condition: new, Booth KPZ-4P • Booth Type Closed drive-thru • Worksize dimensions 3500 width x 1800 height x 1000 depth • Overall dimensions 3300width x 2300 height x 1800 depth • Power supply Electric • Nominal power 0,69kW x4 • Voltage 380V • Frequency 50-60Hz • Filters 100% Polyester • Filters count 4 • Filters hang type Bagnet type, easy on/off • Filter area 30m2 • Filter cleaning system Pneumatic - Jet Venturi Crodpfsbxmfnex Addjk • Ventilator type Aluminium ray rotor . • Air consumption 20,400m3/h • Loudness 74dBa • Doors Double, both side • Inside drive diameter 800mm

Condition: new, Year of construction: 2025, ARE YOU INVOLVED IN CUTTING THICK LOGS AND ARE YOU LOOKING FOR A POWERFUL BAND SAW THAT WILL CUT YOUR THICK LOG WITHOUT PROBLEMS? THEN WE HAVE A SOLUTION FOR YOU, THE HORIZONTAL BAND SAW WRC 1550! Credpfx Adev R Umuedjk ✔️ROBUST CONSTRUCTION THAT ENABLES SAW STABILITY ✔️MAIN MOTOR 55-110kW ✔️IDEAL RATIO BETWEEN THE DIAMETER OF THE MAIN WHEELS, THE WIDTH OF THE MAIN WHEELS, THE LENGTH, WIDTH AND THICKNESS OF THE BAND SHEET, WHICH ENABLES ACCURATE, FAST CUTTING ✔️DOUBLE-SIDED BEARING WHEELS THAT ENABLE STABILITY OF THE MACHINE EVEN IN THE LONG TERM! ✔️COMPLETE HYDRAULIC EQUIPMENT ON THE SAW HEAD ✔️COMPLETE HYDRAULIC EQUIPMENT ON THE SAW LINE (INCLUDING HYDRAULIC DOUBLE TURNERS DESIGNED SPECIFICALLY FOR TURNING THICK HEAVY LOGS) 👉 For more information and inquiries, contact us!

Condition: used, Year of construction: 2009, HOLZ-HER edge banding machine CONTRIGA 1366 Edge thickness: 0.4-30 mm (depending on equipment) Edge height: 51/66 mm (depending on equipment) Panel thickness: 6-45/60 mm (depending on equipment) Edge types: Rolls and strips Feed speeds: Continuous feed from 12-30 m/min (depending on equipment) With adjustable infeed level in the magazine area (max. adjustment range 30 mm) With height-adjustable magazine plate for changing the lower edge overhang With large magazine plate Ø 820 mm for edge rolls up to Ø 800 mm With transport chain including automatic central lubrication With motor-driven, position-controlled bridge height adjustment With pneumatic locking roller for the shortest workpiece sequence With extendable workpiece support (extension width 1600 mm) With space-saving, pneumatically controlled sliding hoods over the entire machine (Deviations for individual units are possible) with motorized infeed guide with injection oiler for lubricating all joints and bolts (including operating hours counter) with central connection for extraction (2x Ø 200 mm) with integrated chip collection box at the end of the machine (when radius scraper unit is installed) PPC 231 control system - Power PC for efficient setup and changeover - 15" SVGA screen with touchscreen - 128 MB CF memory card - USB connector on board - Ethernet network connection - Keyboard connector on board - Windows-like user interface - all information in plain text and/or graphics - Rotatable and pivoting control panel at eye level - Dust-proof membrane keyboard with softkeys (pushbuttons) - LED display for unit preselection - Program list with program names and numbers - Extensive program memory - Individual selection of the units with the functions as basic setting options for setpoints, route points and tool corrections as well as the fixed route points - Centralized and clear setup processes for units and their axis settings via fine adjustment (depending on the equipment) - Interval display for the shortest workpiece distance - Integrated path control - Path points are controlled generally or program-specifically - Clear and complete recording of all operating data - Service messages in plain text - Diagnostic system - including integrated synchronous bus system for high precision in unit control - Individual administration for up to ten users, including password protection - Online maintenance (optional), data exchange with HOLZ-HER Service - Barcode interface (optional) BASIC MACHINE CONTRIGA 1366 - Belt bridge Options and accessories for the basic machine Spraying device 1856 for the inlet and outlet area For the inlet area: Electronically controlled release agent sprayer with Riepe-LPZ/II release agent For the outlet area: Electronically controlled cleaning agent sprayer with Riepe-LP163/93 cleaning agent (only in conjunction with pre-milling unit 1961 and surface scraper 1964) Joint milling unit Joint milling station 1803 (2x 2.6 kW, 200 Hz, 12000 min-1) With two plunge-controlled milling units 1 unit in up-cutting direction 1 unit in down-cutting direction Plunge path 5 mm With static frequency converter 200 Hz Without milling tool With ProLock screw-in clamp for fast tool changes Tool for 1803 (workpiece height up to 60 mm) Diamond milling cutter PRO UT 2 pieces (front and rear) including protective covers Ø 100-63 - Ø 30 mm, Z = 3 + 3 + 3, 1x left-hand rotation, 1x right-hand rotation Noise-reduced milling cutter with integrated chip guide DFC technology (Leitz syst Cedpfx Aovvkfdjddork

Condition: reconditioned (used), functionality: fully functional, power: 9 kW (12.24 HP), Ott veneer press Crodpfx Aotwp Iwjddok connected load 380V 9kW Panel size 2250 x 1350 mm Elkom heating plates, gold anodized Plates and hydraulics in order

Condition: like new (used), Year of construction: 1996, Retrofitted: 2025 Crsdpewfunyefx Addok Numerical control: NUEVO/NEW HEIDENHAIN TNC-320 Technical features Dimensions Table dimensions: 6000 x 2000 mmNumber of T slots: 13T slots dimensions: 22 mm Traverses of axis X axis traverse: 6000 mmY axis traverse: 3800 mmZ axis traverse: 1000 mmVertical capacity (VC): 500 / 1500 mm (direct exit)Distance between columns: 3100 mm Milling head Universal head UM40 (Body B: manual / Body C: 3º auto-indexing) Direct spindleTool clamping system: HydraulicTaper nose: ISO50 (DIN-69871)  /  Pull stud: DIN-96872Speed range: 3000 rpmSpindle power: 30 kW Feedrates Rapid feedrate (X / Y,Z): 7200 / 12000 mm/min Weight and dimensions Machine weight approximate: 50000 KgMaximum weight on table: 15000 kgMachine dimensions approximate: 14740 x 5330 x 5050 mm Accesories Guarding: 2 sliding doors with a new perimetral wire-mesh safety fenceHead changer: automatic with lateral hinge/support in columnChip conveyor: 2 longitudinal palletsElectronic handwheel: New HR-510Coolant: External Internal high pressure through spindle (internal only with direct exit head) Sales conditions Guarantee: 6 months mechanical spare partsSale conditions and price: On request View all technical features