Shredders Zeno ZTLL 1000x1200 1999

Zeno ZTLL 1000x1200

Condition: good (used), Intake opening: 1.000 x 1.200 mm Motor power: 37 kW Rotor flight circle: 450 mm Rotor speed: approx. 86 rpm Cutting system: 51 cutting inserts Fodsbyiq Ijpfx Aalogk Screen: quick-change-device, Ø 80mm Machine weight: approx. 3.500 kg

Condition: refurbished (used), Year of construction: 2018, Mobile hammer mill Mobil Flex 1000 with drum magnet and discharge belt Drive: 250 Kw electric 4-hydraulic supports for lifting the machine for transportation Total weight: 33,000 kg Rotor weight: 3,000 kg Production: up to 11 to/h (depending on material size, grid size, parameter settings) With soundproof housing Dimensions: 11,750 x 2,500 x 4,380 mm Fgedpfx Aeph Uy Tsalek Number of hammers: 24 pcs. Hammer weight: 22 kg System is being overhauled

Condition: as good as new (ex-display), Year of construction: 2023, operating hours: 3 h, functionality: fully functional, machine/vehicle number: 237042, power: 25 kW (33.99 HP), overall weight: 1,575 kg, fuel type: electric, color: yellow, From my own experience: The battery lasts a whole working day without any problems when continuously charged Internal number: M1241 Manufacturer: Schliesing Vehicle type: trailer chassis Drive type: electric Log diameter: Ø 20 Feed width (mm): 240 Engine power: 25 kW - torque of 120 Nm Year of manufacture: 2023 Operating hours: approx. 3 Own weight (KG): 1575 Equipment: Power Control System - whisper-cut shredding system The Schliesing mid-range is now also available as an electric shredder - the Schliesing 325MX-E shredder. The powerful brushless asynchronous motor with an output of 25 kW and a torque of 120 Nm ensures productive work with the usual pulling power. The batteries are designed to enable a full working day without charging. The 325MX-E enables emission-free chipping with low noise levels and offers uncompromising productivity for logs up to 20 cm in diameter. Engine and chassis: Brushless asynchronous motor with 25 kW and a torque of 120 Nm Fully galvanized, corrosion-resistant single-axle chassis for 80 km/h including EU homologation Robust, solid and widened sheet steel mudguards Solid support wheel at the front and parking support at the rear Towing device with overrun brake and soft dock ball coupling or DIN towing eye LED lighting in accordance with StVZO (impact-protected) Pneumatic tires 205/65 R15 C Battery: LEP battery (lithium iron phosphate) with a capacity of 300 Ah at 96 V Allows the chipper to be used for a full working day without charging. No recharging required during long downtimes Energy recovery through recuperation of the kinetic energy of the chipping disc during the work process Charging connection: protective contact plug 220-240V/16A Charging time for full charge: 8 hours Guarantee for 1000 charging cycles at 80% SOH (State of Health) Housing/hopper/blow-out pipe: Foldable intake hopper with at least 1,500 mm input depth Fully galvanized, corrosion-resistant hopper flap Funnel dimensions (inside): width = 1,040 mm, height = 960 mm Pivoting blow-out pipe with adjustable spreading flap Blow-out pipe on ball bearing slewing ring Relevant machine parts with sound insulation (especially chipper hood and blow-out pipe) Two emergency stop buttons on top of the hopper and on the side of the hopper flap Chipping mechanism: Chipping mechanism with safety circuit according to EN 13525 Robust chipping disc Ø 655 mm, 35 mm thick Fsdsvmz N Uopfx Aalogk Closed blade system for quick, safe and precise blade changes Continuously adjustable chipping blades Chipping blades can be resharpened multiple times for a long service life (approx. 10x) Horizontally usable counter blade and vertically usable counter blade, each 2-fold for a long service life Winding protection on the main bearing of the chipping disc Hydraulic feed: Feed control with its own hydraulic circuit PowerGrip feed roller, 240 mm wide, with hydraulic feed. Particularly grippy, aggressive and even feed thanks to one oil motor per roller Parallel-guided top roller for regular and even feed to prevent jamming of the fed material Hydraulically adjustable feed speed and thus the wood chip size Fill level indicator for hydraulic oil tank OPTION OVERVIEW: The Whisper Cut® V-shaped blades feed the wood more evenly and with less vibration In combination with the centering PowerGrip roller, the chopped material hardly swings back and forth

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Fodpsu Thhrjfx Aalogk Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2024, operating hours: 10 h, condition: like new (used), Extrusion Line with Densifier – Ideal for Recycling Applications This robust and versatile extrusion line is perfectly suited for recycling polyolefins such as LDPE, HDPE, and PP. Thanks to the integrated densifier, even materials with low bulk density – such as regrind, EPS, film scraps, and other lightweight plastic waste – can be processed efficiently. The densifier compacts the loose material and feeds it directly into the extruder, ensuring a consistent material flow and stable extrusion process even with challenging input materials. Fgjdpfx Ajtziudealek Key Features: • Suitable for all types of polyolefins • Ideal for lightweight, bulky materials like EPS or film regrind • Efficient feeding system via integrated densifier • Compact design and easy maintenance This line is an excellent choice for recyclers, plastic processors, and compounders who require flexibility and reliable performance when working with diverse input materials.

Condition: used, Chipping roundwood: 100-150 m3/h Chipping small waste: 50-100 m3/h Fgjdpfehclffsx Aalok Weight: 3165 kg Max log diameter: 254 mm Söderhamn Eriksson 670-56 CC chipper with electric motor. Söderhamn Eriksson 670-56 chipper is intended for the production of chips for pulp, fibreboard and chipboard manufacture. Both roundwood and sawmill waste may be used as raw material. Chipper 670-56 feed is horizontal, at an angle of 37,5 grades to the grain. The chips, of consistent high quality, may be discharged at the bottom or blown straight upwards. Be one of those woodworking companies that wisely manage the resources available to them.

Year of construction: 1998, condition: excellent (used), NEUE HERBOLD cutting mill / granulator Universal mill - heavy version Made in stainless steel -Year of construction 1998 - made of stainless steel - from technical center (machine was used exclusively for test/demonstration purposes Fsdpfx Ajh Rwc Eoalogk - Rotor diameter: 300 mm - Working width: 500 mm - 3 rows of knives

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, machine/vehicle number: WKZ45-1030, CLEARANCE SALE, STOCK MACHINE! We invite you to visit our technical center to experience the quality and functionality for yourself. Material Shredder 45KW Hopper opening: 1,030 x 1,235 mm Rotor diameter: 360 mm Star-delta start, automatic shut-off during idle - Hydraulic pusher equipped with pressure plates - Siemens PLC control - Optionally with control cabinet extension for discharge conveyor belt and overband magnetic separator Complete solution with discharge conveyor belt in any configuration. Our core competence lies in delivering exactly what the customer truly needs. We work together with our customers to develop customized, individual solutions and supply corresponding systems from our own production. Please feel free to contact us by phone to find the right solution for your application. Fodpfxjv Tdq Ij Aalegk Conveyor belt, conveyor system, discharge belts, belt conveyors, magnetic separators, overband magnetic separators, recycling, wood chips, plastics, metal-free, metal detection, neodymium, overband magnet, magnetic belt separator, lifting magnets, filter rods, magnetic grids, magnetic grate, metal separator, block magnet, filter systems All prices are net prices plus 19% VAT All information provided without guarantee, while stocks last!

Condition: used, Granulation and packaging line. Model: HM700E PRO 11KW Year of manufacture: 2022 It includes: Hammer mill - shredder Chip mixer Chip feeder Granulator Vibrating table Product feed belt (conveyor belt) Pellet hopper with packaging equipment Bag sealer and chip moisture meter Fsdpfx Aajxcy D Eslogk Hammer mill with cyclone Motor: 11 kW / 400 V Productivity: 300 - 700 kg / h Weight: 360 kg Soft start installed Cutting system 16 hammers Chip mixer: Volume: 1.0 m³ Chip feeder: Motor: 3.3 kW / 380V Feeds up to 800kg / h Granulator: Motor: 22 kW / 380V/50hz; Productivity: 300 - 700 kg/h Weight: 590kg Soft start installed Vibrating table: Weight 90kg Product feed belt (conveyor belt): Dimensions: 5m × 0.4m. Automated packaging equipment: Dimensions: 1, 90x2, 50x2, 30 Volume: 1.5m³ Packing in bags: 1 - 50kg Equipped with two types of scales Bag sealer 220V Moisture meter

Condition: good (used), Year of construction: 2017, functionality: fully functional, Vecoplan Shredder, Type VAZ 110, year of manufacture 2017, with hopper and extraction port. Manufacturer: Vecoplan Type: VAZ 110 Year of manufacture: 2017 Motor rated power: 18.5 kW Frequency inverter rated power: 22 kW Feed opening: 1200 x 1075 mm Rotor diameter: 250 mm Rotor length: 1075 mm Rotor speed: 90-250 rpm Number of cutting tools: 27 Throughput: 2 cbm/h Screen hole size: 20 mm Extraction port diameter: 200 mm Dimensions: approx. 2355 x 1590 x 980 mm (LxWxH) Weight: approx. 1800 kg Accessories: Spare parts package with 20 mm screen, 1 set of tools, cutters and counter cutters, motor, plastics, springs, etc. Materials: Wood waste, films, packaging material, chipboard, paper, textiles Remarks: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find the video on our website or YouTube channel. Complete documentation including CE declaration is available. Fjdpfx Aasw Rcrielogk Inspections can be arranged at any time by appointment. On request, we are also happy to carry out test runs with your material for a handling fee. If you have any questions about the machine, we are available by phone Monday to Thursday from 08:00 to 14:00 h and Friday from 08:00 to 13:00 h. Please note: All technical data is based on manufacturer information. We do not accept liability for the information provided or any possible errors. All offers are subject to change, prior sale, and revocation at any time. Inspections can be arranged upon request. Sale is ex location, without warranty or guarantee.