Used other waste management & recycling machinery for sale (84)

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Cgodpfx Aiju Tg I Deaeu Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: like new (used), 2 units of feed and dosing bunkers with rasp discharge, suitable for light and organic materials (e.g. wood chips). Dimensions (L x W x H): approx. 9.1 m x 2.8 m x 2.5 m (with legs approx. 3.8 m). Discharge via 4 shafts each, driven by a 1.1 kW geared motor. Cedpfsyv Ef Rox Aiasgu

Condition: good (used), Used Thetford International T3 waste compactor. Cjdpfohvi Ahox Aiasgu

Year of construction: 2012, condition: good (used), functionality: fully functional, Rotary Airlock Valve / Rotary Valve Nestro, year of manufacture 2012, for the separation / differentiation of paper chips or paper edge strips Technical data: Manufacturer: Nestro Lufttechnik GmbH Year of manufacture: approx. 2012 Motor: 4 kW Max. volumetric flow: 28,000 m³/h Max. inlet diameter: 450 mm Speed: 22 rpm Rotor width: 1,500 mm Rotor diameter: 1,200 mm Dimensions: 2,200 x 2,200 x 2,500 mm (LxWxH) Weight: approx. 3,000 kg Remarks: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find the video above on our website or on our YouTube channel. Csdpfx Aoy Tiagsiaogu Inspections, including under power, are possible at any time by prior arrangement. We are happy to answer your questions about the machine by phone, Monday to Thursday from 08:00 to 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data is based on information provided by the manufacturer. We do not accept liability for the stated information or possible errors. Offers are non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are possible by arrangement. Sale is ex-works, advance payment required, without warranty or guarantee.

Condition: used, Rotary valve, rotary airlock Cgedpfx Aijy Th I Nsaeu Manufacturer: TrennSo Type: AS 600x1400-6 Working width: approx. 1400 mm Rotor with flexible, replaceable rubber lips With free shaft end, without drive Condition: unused

Year of construction: 2018, condition: good (used), For sale: a machine for pelletizing. ARtechnic PBPe.500x-k. Cedoy T Itxopfx Aiajgu

Year of construction: 2022, operating hours: 1,471 h, condition: like new (used), Automatic classification and separation of various types of materials (plastic, film, paper, metal, textile, wood, etc.) by composition (NIR), color (VIS) and/or shape. Approximate dimensions: 1923 x 2175 mm. Height: 2055 mm. Approximate weight: 1080 kg. Csdoy Sm Daspfx Aiaogu

Year of construction: 2022, operating hours: 1,325 h, condition: like new (used), functionality: fully functional, Separation of Fe fraction. Material density 0.25 t/m3. Nominal grain size 300 mm. Maximum grain size 1000 mm. Approximate dimensions: 2755 x 1275 mm. Height 645 mm. Approximate weight 2.6 t. Cgodpfey Smxkox Aiaju

Year of construction: 2013, condition: used, We offer you a used PET bottle crusher of the manufacturer BOREMA, type R-1200 F, year of construction 2013, for residual emptying, deaeration and pre-compaction of the fed PET bottles, from 0.3 up to 2.5 l content. The machine has a chassis and can be moved into and out of the feed chute of your baler. The machine has a throughput capacity of approx. 85,000 bottles/h, corresponding to approx. 3t/h. We have the following technical information: Manufacturer: BOREMA Umwelttecjhnik AG Type: R-1200 F (with trolley for retracting and extending) Year of manufacture: 2013 Drive power: 11 kW Connected load: 15 kW Rated current: 32 A Back-up fuse: 40 A Type of construction: Continuous system Function: Double rotor press system Rotor pretension pneumatic: approx. 16t Overload protection: by anti-blocking system Input material: PET disposable and returnable empty bottles 0.3 to 2.5 L capacity Input material: HDPE bottles and canisters up to 3 l capacity Throughput capacity: approx. 3 t/hour, corresponding to approx. 85,000 bottles/hour, depending on size Required compressed air output: G1/2", 8 bar, 40 l/min. Compression ratio: 1:3 Flange dimensions inside: 972 x 1220 mm Feed opening: 565 x 1280mm Weight: approx. 2500kg Cedpfxou Thpno Aiasgu Possible applications: Due to the chassis, the PET flattener can be moved into the feed chute of your baler as required, thus ensuring residual emptying, venting and pre-compaction of the fed bottles and canisters. When the material is changed, the PET flattener is simply moved out of the feed chute again and paper, cardboard, film, etc. can now be pressed further without using the flattener. Process of the BOREMA PET crusher: The plastic packages are drawn in by two rotating shafts. One of the rotating shafts is pneumatically pretensioned by two air bellows and presses the PET bottles with 16 t of pressure against the second rotating shaft. In the process, the closed plastic bottle is squeezed together, caused to burst and vented. Residual liquids run out and the material falls into the baler in a precompressed state. When impurities are introduced, the pneumatically pre-tensioned shaft deflects to the side and the impurities are channeled through. Significant advantages compared to conventional PET perforators with punching mandrels or knives: The BOREMA process is much more efficient and less subject to wear than conventional PET perforators with punching mandrels or knives. The biggest advantage is that any foreign matter such as metal parts, stones, bottles with frozen contents and pieces of wood are passed through the pneumatically deflecting rotor shaft without stopping the operation of the system or causing any major damage. With conventional perforators, mandrels or blades sometimes break off or become so jammed with the interfering material that the plant has to be shut down and repaired at great expense. Comments: The crusher is in good condition, was dismantled from the running operation, stored, is available at short notice and after assembly immediately ready for use. The documentation (manual, CE, electrical/hydraulic circuit diagram) is complete. An inspection is possible by arrangement. The technical information is taken from sales brochures, the operating instructions or other information provided by the manufacturer. We accept no liability for incomplete or incorrect data and informations.

Year of construction: 2001, condition: excellent (used), functionality: fully functional, Compost Turner BACKHUS 10.10. Diesel engine: 264 hp Weight: 14.9 t Codpey Equ Hjfx Aiasgu Current videos can be provided upon request.

Condition: used, overall weight: 10,000 kg, power: 55 kW (74.78 HP), Electro-Hydraulic orange peel grab, 6tines, weight 10000kg, about 6m3, with radiation meter Cedpfxoy Ia H Te Aiajgu

Year of construction: 2002, condition: like new (used), functionality: fully functional, L x W x H: approx. 12,1 x 3,0 x 3,25 m Volume: 55 cbm Cgjdpfxellvpzj Aiaeu capacity: approx. 150 m³/h 6 dosing-/discharging-screws - pair driven each 11 kW weight: approx. 15 t.,

Condition: used, machine/vehicle number: 10521, Length of magnetic grinding table = 1300 mm Drive = 13.5 kW Codjyr Tyyepfx Aiaegu Magnetic table can be swiveled Ideal for re-sharpening rotor and stator blades Water cleaning with filter cloth

Year of construction: 2026, condition: like new (used), BigBag frame for emptying Csdpfx Ajy Rfbhsiaogu Top support for spreader beam Spreader beam for forklift / crane

Condition: used, machine/vehicle number: 12195, Infeed: 600 x 600 mm Cgsdpfxjyr Tnqs Aiaeu Drive: 2 x 37 kW

Condition: used, machine/vehicle number: 9394, Year of manufacture: 2015 Technical Data: Main dimensions (length/height/width): 1430/1730/780 mm Cjdjyr Tlijpfx Aiajgu Discharge opening diameter: 102 mm Number of knives and blades: 3+1+9 Drive: 22 kW Total machine weight: approx. 400 kg Possible screen perforations: Ø 4–25 mm

Condition: new, The ZSH chipper series is specifically designed for forestry, horticulture, and municipal operations. These chippers are primarily used for volume reduction of tree and shrub cuttings as well as smaller trunk diameters. The produced wood chips are suitable for combustion in wood chip heating systems with screw conveyors or as a pre-stage in pellet production. The machines are robust, reliable, easy to operate, powerful, and produce wood chips of consistent quality and uniform size. Other features Csdeyr Tkfspfx Aiasgu Cost-effective solution for wood chip production | Compact design | User-friendly | Low energy consumption

Condition: new, machine/vehicle number: AMIS Kabelaufbereitung, System consisting of a granulator, sorting table for separating liberated plastic and copper granulate, extraction unit, and control cabinet. Each component is pre-assembled as a transportable element on base plates. Cgjdpfxeyr Ti Uj Aiaeu Advantages of the compact system: low overall height, minimal space requirements, component arrangement designed for easy cleaning and maintenance, short installation time, and last but not least, attractive pricing.

Condition: new, machine/vehicle number: 10463, The AR series are slow-running machines. They are available with 2, 4, 6, or 8 screw shafts. Each screw unit is installed independently and separately in the chassis. Screw shredders are designed for the shredding of brittle materials (wood, paper, gypsum, mineral wool, etc.). The machines are largely insensitive to contaminants such as glass, metal parts, stones, etc. Cgjdpfx Aijyr Ti Isaou The AR series is optimally suited for use as a bale opener, e.g., for PET bottle bales.

Condition: new, In every economic and public sector calculation, waste transportation is a critical factor. Here, it is not so much the weight but rather the volume that matters. The continuously rising transport costs for this waste are becoming an increasing economic issue. Proper disposal of large quantities of polystyrene or packaging film is particularly important in the retail sector. The VOLUME REDUCER ensures a volume reduction of up to 80 percent at this point. Bottles of any type and size, e.g., sparkling wine bottles, can be shredded effortlessly without the need for a compression mechanism. It is also possible to unpack expired food products. Furthermore, reject items such as pharmaceuticals, data carriers, or counterfeit products can be rendered unusable. Food residues and organic waste, including bones, can be shredded, collected, and converted into electricity and heat in biogas plants using the VR60. Consider, for example, a reverse vending machine for deposit bottles. PET bottles are compressed and held under lock and key until collection due to the presence of a barcode. By using the VOLUME REDUCER, the barcodes on PET bottles could be made unrecognizable, thereby achieving significant volume reduction. The shredded bottles could then be collected in a large container, eliminating the need for daily collection at return points. The shredder's vertically moving, wear-free blades ensure a quiet and clog-free operation. ALL ADVANTAGES AT A GLANCE - Non-rotating shredder - No material entanglement thanks to non-rotating blades - Automatic feed through blade movement - Automatic reversing V-shaped blades prevent jamming or blockage - Fast component change thanks to modular system - Intelligent control via compact logic system (PLC) - One-button operation - Optional material discharge via conveyor belt - Shredder module can be integrated into existing systems Csdpfsyr I H Uex Aiasgu - Low blade wear and maintenance costs due to highly abrasion-resistant steel with a nominal hardness of 600 HBW VR60 IN DETAIL - Dimensions: 90 cm x 70 cm x 85 cm - Weight: approx. 190 kg - Power consumption: 3 kW - Connection value: 400 V three-phase alternating current

Operating hours: 1,071 h, condition: excellent (used), functionality: fully functional, Year of manufacture: probably 2012. The machine features a functional central lubrication system installed in that year. No nameplate is present. Operating hours are indicated by the meter (status as of today). Original documentation and a spare parts catalog are included. The machine is operational and can be inspected under working conditions. A manufacturer’s brochure and an operational video are available upon request. (These are also accessible online and on YouTube) Max. windrow height: 2.3 m Rotor length: 3.7 m Transport dimensions (W x L x H): 2.92 x 5.70 x 2.48 m Transport weight: approx. 6 t Required tractor power: from 210 hp Csdpoy E Im Aefx Aiasgu Turning rate: 1,000 - 2,000 m³/h Operating speed: 50 - 1,000 m/h

Condition: new, This machine can process cables up to 120 mm in diameter – at a rapid 40 meters per minute! A 400-volt power supply and 3 kW output require a three-phase connection. Despite its lightweight construction of only around 220 kg, the machine stands independently and is about the size of a tall household appliance. Key feature: ultra-fast processing of cable diameters between 20 mm and 120 mm. Technical data: Width: 68 cm | Depth: 59 cm | Height: 130 cm | Weight: 220 kg | Speed: 40 m/min | Voltage: 380 V | Power: 3 kW | Cross-section: 20–120 mm Cgodpfjy H Ikwjx Aiasu

Condition: good (used), Year of construction: 1990, functionality: fully functional, - Year of manufacture: 1990 - 3 x 90 kW drive - Including press feed and discharge conveyor (including feed bunker); manufactured by ATM; year of manufacture: 2012 Csdpsy Dtb Aofx Aiajgu The complete line is in very good condition and immediately ready for operation.

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, total width: 6,265 mm, total length: 7,420 mm, total height: 3,900 mm, Baling Press Henschel PS 3-30 / 30 B Year of manufacture: 1999 (refurbished and modernized by ATM in 2016) Immediately operational (all necessary repairs and servicing have been carried out by us) Main dimensions of the entire machine: Length: 7420 mm Width: 6265 mm Height: 3900 mm Cgjdeyx Axgjpfx Aiaou Total weight: approx. 38 t Feed opening: 1210/2150 x 1900/2340 mm Technical data: Motor: 1 x 90 kW Pressing force: - 1st compression: 1000 kN - 2nd compression: 1570 kN - 3rd compression: 2000 kN - Bale door closing force: 200 kN Bale size: 300 x 300 mm

Condition: excellent (used), Year of construction: 2001, Briquetting press for metal chips or granules was only tried on a trial basis Cedpfx Ajfb T Husiajgu hardly run 20 hours of operation 2000 kg/cm2