Year of construction: 2021, condition: ready for operation (used), functionality: fully functional, FLOW & THERMAL Regenerative Thermal Oxidizer (RTO), 18,000 Nm³/h (2021) Complete industrial system for the treatment of process water containing Volatile Organic Compounds (VOCs), consisting of stripping columns and a three-chamber Regenerative Thermal Oxidizer. Manufactured by Flow & Thermal Solutions / TECAM in 2021, the equipment was installed at a PET production plant and remained operational until the factory closed on 27 November 2025. The system removes VOCs from the water by means of air stripping and subsequently destroys them in the RTO through high-temperature thermal oxidation. Heat recovery through ceramic media helps reduce natural gas consumption. Main features • Manufacturer: Flow & Thermal Solutions / TECAM • Year: 2021 • Serial number: F002 • RTO nominal capacity: 18,000 Nm³/h • Configuration: three-chamber regenerative RTO • Fuel: natural gas • Honeywell / Eclipse TJ 200 burner • Burner output: 58–586 kW • Electrical supply: 400 V, 50 Hz • Electrical power stated on the nameplate: 40 kW • 30 kW Soler & Palau ATEX main fan • Siemens PLC automation with HMI touchscreen • LEL monitoring, purge, dilution, bypass and pneumatic valve systems • Vertical stack: 10 m high, diameter: 800 mm • CE marked Pgodpfx Apszvcknohor Performance and operation The equipment operated at actual flow rates close to its nominal capacity, with recorded values ranging from approximately 16,400 to 17,900 Nm³/h. The latest available emissions test, carried out by DEKRA in December 2023, recorded the following values: • TOC: 13 mgC/Nm³ • NOx: 3–4 mg/Nm³ • CO: 125–153 mg/Nm³ During the tests, the equipment operated at an approximate temperature of 775–780 °C, with a treated water flow rate of 3.5 m³/h. Stripping columns The system includes: • Original stripping column, designed for approximately 6 m³/h. • Second Tecnium SLFKK9 stripping column, manufactured in PPH, with a nominal capacity of 8 m³/h and a maximum capacity of 10 m³/h. The second column was installed, but it is currently dismantled and lying on the ground after being knocked down by strong winds during the winter. It has a hole in the base which, according to the available information, is considered potentially repairable. The Tecnium column is equipped with internal packing, distributors, a mist eliminator, connections, drainage and provisions for integration with the existing control system. Condition and maintenance The system remained operational until the final closure of the plant in November 2025. The latest preventive maintenance was carried out by TECAM in June 2025 and included mechanical and electrical inspection, burner, fans, stripping columns, instrumentation, valves and functional testing. The equipment was operational, although maintenance work is required before recommissioning, mainly involving: • Process valves • Internal insulation of the towers • Ductwork and seals • Main fan impeller and expansion joints • Repair of the base of the second stripping column TECAM technical documentation is available regarding the recommended works, and several spare parts are also available. Scope of supply The system includes: • Three-chamber RTO • Combustion chamber • Burner and gas train • Main fan • Two stripping columns • Dilution and purge system • Hot bypass • LEL analysers • Stack • Ductwork • Electrical cabinets and controls • Platforms, ladders and support structures • Available spare parts

Condition: excellent (used), 3,000 L Complete Pilot Bioreactor / Fermentation System Complete 3,000 L pilot-scale bioreactor installation, fully skid-mounted and integrated on a stainless-steel frame. The complete system is built as an integrated stainless-steel skid installation, including the process vessel, pumps, piping, valves, instrumentation, control system, and auxiliary equipment. The skid is equipped with a platform and access stairs. The installation is highly suitable for testing, developing, and optimizing fermentation processes on a pilot scale. Main components: - Stainless-steel conical process vessel - Maximum working volume: 3,000 L - Heating/cooling jacket - Sampling connection - Custom-built sparger for air/gas injection - Cambridge Sensotec Rapidox 3100 off-gas analyzer - 4 × Watson Marlow 0XZ-63L/4 dosing pumps - Mettler Toledo InPro3250i pH sensor - MT 6850i DO sensor - Endress+Hauser TMR35 temperature sensor - Aerzen blower with 7.5 kW electric motor - 2 × 0.2 μm PTFE air filters - Bran+Luebbe N-K11 plunger pump - Netzsch 4NL30A and 4NL40A progressing cavity pumps - Recirculation system - Complete CIP system - Gas control system including control valves and MFCs - PLC control system for pumps, valves, temperature, DO, and other process parameters - SCADA system for monitoring, operation, data logging, and data export - DO cascade control - Complete stainless-steel skid/frame with platform and access stairs - Vibrating sieve - Sieve bend - Screw press - Aseptic capability with tank modification The current installation is not designed as an aseptic system. However, the existing process vessel can be replaced with a suitable aseptic vessel, making it possible to adapt the installation for aseptic fermentation applications. Including documentation and technical knowledge from the manufacturer. In addition, all available technical knowledge regarding the installation, operation, and maintenance is available, providing an excellent basis for future commissioning, operation, and servicing. Pjdpfezw Rklsx Aphegr Complete Integrated Pilot System A highly versatile 3,000 L pilot fermentation system, combining process vessel, pumping, dosing, aeration, temperature control, CIP, process instrumentation, and advanced PLC/SCADA control in a complete stainless-steel skid-mounted installation. An excellent solution for pilot-scale fermentation development, process testing, and optimization.

Condition: like new (used), Year of construction: 2019, operating hours: 300 h, functionality: fully functional, overall weight: 2,500 kg, rotational speed (min.): 4,500 rpm, screw diameter: 305 mm, year of last overhaul: 2026, temperature: 80 °C, empty load weight: 2,500 kg, power: 22 kW (29.91 HP), Equipment: documentation/manual, rotational speed infinitely variable, Complete Technical Data (GEA OCE 305-01-32)Technical ParameterSpecification and ValuesManufacturer & ModelGEA Westfalia Separator Group GmbH – OCE 305 SeriesEquipment TypeHigh-performance 2-phase decanter centrifuge (Solid-Liquid)Bowl Inner Diameter305 mmBowl DesignFlat-cone design with an extended length (Extended L/D ratio)Maximum Hydraulic CapacityUp to 5 m³/h (varies depending on solid concentration)Maximum Solids Density 2.6 kg/dm³Drive Type2-Gear Drive (System with 2 independent motors, no magnetic brake)Differential Speed ControlAutomatic via dedicated Variable Frequency Drives (VFD)Overall DimensionsLength: 3000 mm | Width: 1000 mm | Height: 1150 mmTotal Weight (Complete Skid)Approx. 2500 kgLubrication SystemAutomatic centralized grease lubrication for main bearingsConstruction MaterialsHigh-grade duplex stainless steel (all product-contact areas)Scroll Wear ProtectionSintered tungsten carbide tiles welded onto the flight edgesII. Liquid Discharge Under Pressure SystemUnlike standard models with gravity discharge (where the liquid falls freely into acollection tank), your model retains the clarified liquid phase inside a hydro-hermetic tripetal Pump (Paring Disk): The separated liquid flows toward the cylindrical end of the bowl, entering a special chamber where a stationary disk with spiral internal channels (a reverse turbine) is etic-to-Pressure Energy Conversion: The kinetic energy of the rapidly rotating liquid is instantly transformed into hydrostatic pressure when it hits the channels of the stationary cess Advantages: The liquid leaves the decanter directly under pressure (without requiring an external transfer pump). This prevents product foaming (highly critical for oils, chemical products, or food-grade applications) and eliminates contact with atmospheric oxygen Electrical cabinet with frequency inverters ant PLC (Siemens ) with acces code for modify the parameters , including factory documentation Pjdjzgq Szjpfx Aphegr

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, machine/vehicle number: 99900338790, wall thickness: 10 mm, overall weight: 1,300 kg, control cabinet length: 700 mm, control cabinet width: 400 mm, control cabinet height: 2,000 mm, total height: 1,300 mm, total length: 2,300 mm, total width: 800 mm, inner dimension length: 2,000 mm, empty load weight: 1,300 kg, Equipment: documentation/manual, The GEA Westfalia Separator UCD 305-00-00 is an efficient two-phase decanter designed for effective separation of liquids and solids. Thanks to its flat conical trommel and extended drum length, it optimizes the separation process and ensures effective liquid discharge. DRUM AND HOUSING CONSTRUCTION The standard housing design provides a robust construction that meets the requirements of industrial applications. Inert liquid discharge enables easy operation and reduces maintenance costs. DRIVE TYPES Pjdezrmh Ajpfx Aphsgr The belt drive of the drum ensures reliable and uniform rotational movements, while the worm gear drive enables precise control of solid discharge. This combination guarantees high efficiency and durability of the machine. The GEA Westfalia Separator UCD 305-00-00 offers an effective solution for liquid and solid separation. Centrimax is a good and reliable supplier of this machine. This description may have been automatically translated. For further information, please contact us. The information contained in this advertisement is for general guidance only. We suggest verifying the details with the seller before making a purchase.

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Refrigerant pump station, complete with a control cabinet, pumps, and connecting fittings. The entire unit is mounted on a steel platform. Pgsdpfx Aozu R S Dspher Available for sale as a complete set or in individual components. Pumps with a capacity of 60 m3/hour are also available separately.

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, Industrial self-cleaning disc filtration system manufactured by CHEMIPOL. The unit was installed as part of a reverse osmosis water treatment plant and was used for water pre-filtration. The system is equipped with eight TW-type disc filter units operating in parallel. Automatic cleaning is controlled by a Siemens PLC with an HMI operator panel. TECHNICAL DATA Manufacturer: CHEMIPOL Model: TW8P2L3 Equipment type: Self-cleaning disc filtration system Number of filter units: 8 Filter type: TW disc filters Configuration: Parallel operation Cleaning system: Automatic self-cleaning Pressure monitoring: Two pressure sensors measuring inlet and outlet pressure Control system: Siemens PLC Pgodpfx Apjzvlm Eeher Operator interface: HMI touchscreen Application: Water treatment and reverse osmosis pre-filtration

Year of construction: 2014, condition: ready for operation (used), machine/vehicle number: 5125781, Alfa Laval ALDEC 45 Decanter Centrifuge – For Sale Alfa Laval ALDEC 45 industrial decanter centrifuge in very good working condition. The machine has been well maintained and is suitable for continuous solid-liquid separation applications. Key Specifications: Manufacturer: Alfa Laval Model: ALDEC 45 Year: 2014 Machine / Serial No.: 5125781 Maximum Bowl Speed: 4,200 rpm Main Motor: Approx. 22 kW Back Drive Motor: Approx. 5.5 kW Bowl Diameter: Approx. 360 mm Processing Capacity: Approx. 3–15 m³/h, depending on feed characteristics and separation requirements Continuous industrial operation Pgjdpfjzu S Uyex Aphsr Heavy-duty stainless steel construction Location: Türkiye Condition: Very good, ready for operation Suitable for various industrial separation applications, including wastewater treatment, sludge dewatering, chemical processing, food processing and other solid-liquid separation processes. The machine is available for inspection. Additional photos, technical details and videos can be provided upon request.

Condition: good (used), Year of construction: 2015, functionality: fully functional, Equipment: documentation/manual, Vacuum evaporator-concentrator for for the treatment of water-based liquids and effluents by low-temperature evaporation, forced circulation and external heat exchangers. Maximum nominal distillate production: 20,000 litres/24 h (834 l/h, ±10%). Boiler working volume: 1,540 litres. Approximate evaporation temperature: 30–60°C. Operating vacuum: 4–18 kPa absolute. Electrical supply: 400 V, three-phase, 50 Hz. Electrical power consumption: 13 kW. Rated current: 29 A. Specific electrical consumption: 16 Wh/l ±10%. Required thermal power: 593 kW. Hot-water inlet temperature: 80–90°C. Cooling-water inlet temperature: 10–30°C. Compressed-air pressure: up to 8 bar. Approximate empty weight: 2,550 kg; maximum operating weight: 4,500 kg. Approximate transport dimensions: 4,850 × 2,000 × 2,760 mm. Main construction in stainless steel. Equipped with an evaporation chamber, liquid-ring vacuum pump, circulation pump, heating heat exchanger, condenser, distillate tank and discharge pump, pneumatic valves, PLC, touchscreen and instrumentation for level, pressure, temperature and flow measurement. Maximum permissible concentrate density: 1.3 kg/dm³. Maximum viscosity: 10 cP. Maximum recommended particle size: 800 microns. Maximum inlet-liquid temperature: 70°C. Noise emission below 80 dB(A). Not suitable for flammable, explosive, radioactive or chemically incompatible liquids. Pgedpfszvdftjx Apher

Condition: ready for operation (used), Year of construction: 2020, functionality: fully functional, Equipment: documentation/manual, Reverse osmosis plant. Inlet pressure: 3 bar. Capacity: 4 m³/h. Power: 34 kW. Maximum pressure: 55 bar. Equipped with Grundfos pumps, frame, stainless-steel piping, pretreatment system, tanks and control panel. Serial No.: 2005118. Pgodpszvchaofx Aphsr

Year of construction: 2020, condition: ready for operation (used), functionality: fully functional, For sale: AERZEN D62H rotary lobe compressor, manufactured in 2020. Technical data Manufacturer: AERZEN / Aerzener Maschinenfabrik GmbH Pjdozucpnspfx Aphjgr Type: D62H Machine: Rotary Lobe Compressor / Drehkolbenverdichter Year of manufacture: 2020 Nominal motor power: 160 kW Max. suction pressure (abs.): 1.013 bar Max. discharge pressure (abs.): 2.513 bar Max. differential pressure: approx. 1.5 bar / 1500 mbar Unit weight: 2,790 kg Serial number: 4084095 Customer order no.: 223922 Industrial AERZEN compressor suitable for applications requiring high air volume at low pressure. The machine is equipped with the original manufacturer's nameplate. More information, additional photos and price available on request. Worldwide delivery can be arranged. Please contact us for further information.

Condition: like new (used), Year of construction: 2020, functionality: fully functional, tank capacity: 5,000 l, usable tank capacity: 5,000 l, total height: 3,225 mm, outer diameter: 1,756 mm, overall weight: 1,640 kg, wall material: stainless steel, wall thickness: 8 mm, wall structure: single-walled, manhole diameter: 610 mm, manhole location: top, operating temperature: 100 °C, negative pressure: 1,00,000 Pa, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, sanitary facilities, Brand new, never commissioned. Professionally decommissioned from an INEOS manufacturing facility prior to first use. Manufactured by Able Engineering, this high-specification sanitary 316L stainless steel agitated pressure vessel is suitable for pharmaceutical, cosmetics, personal care, food, beverage and fine chemical applications. Designed for vacuum and low-pressure service and suitable for installation within ATEX-rated environments. Constructed entirely in 316L stainless steel throughout with 8mm shell and dish walls, dished top and bottom heads, heavy duty tubular stainless steel leg supports with bolt-down base plates and load cell arrangement, hygienic internal finish < 0.8 Ra, and full hygienic ferrule fittings throughout conforming to ASME BPE / BS3062. Suitable for CIP. Material: 316L Stainless Steel throughout. Working Volume: 5,000 Litres. Shell ID: 1,740mm. Overall Height: 3,225mm. Shell & Dish Wall Thickness: 8mm. Design Pressure: -1.0 to +0.45 Bar.G. Design Temperature: -10°C to +100°C. Empty Weight: 1,640kg. Design Code: PD5500:2018, Cat.3. PED 2014/68/EU certified. Manufacturer: Able Engineering. Serial Numbers: PXL19635-1, PXL19635-2, PXL19635-3. Factory Tested: September 2020. Fitted with SEW-Eurodrive geared agitator with double mechanical seal, seal pressure pot, and reinforced agitator mounting. Nozzles and fittings include 610mm hinged manway, CIP inlet with dip pipe and TOD clip-on spray fitting, pressure relief valve connection, nitrogen blanketing connection with pressure indicator, Endress & Hauser hygienic thermowell, dual flush polished level switches, load cell arrangement on support legs, lifting lugs, and earthing boss. Three units currently available, all brand new and never commissioned, sourced directly from the same INEOS facility. Tank saddles available on request for either single use or purchase. Please view our other listings for additional sizes and configurations — all stock is brand new, ex-INEOS, and available for immediate inspection and purchase. Pedpfx Apezhnlzehegr Original engineering drawings and full nameplate documentation available on request. Inspection welcome by appointment. Loading and transport can be arranged. Tracht Ltd specialise in hygienic process equipment for the food, beverage, cosmetics, pharmaceutical and chemical industries, with practical experience supporting both batch and continuous manufacturing environments. In addition to process vessels, Tracht Ltd supply and install stainless steel mixing vessels, Silverson high-shear mixers, hygienic lobe pumps, hygienic centrifugal pumps, access gantries, and provide full vessel installation and commissioning services. Whether replacing existing equipment or expanding production capacity, Tracht Ltd can specify, supply and install the right equipment for your application. Please contact us for further information or to discuss delivery and installation options.

Condition: excellent (used), functionality: fully functional, machine/vehicle number: 358143, Hydra-Cell G10XKSGSFEMB diaphragm high pressure pump with 4 kW motor, build in inverter, manual control unit (on/off and speed), external cooling and 34,5-69 bar over pressure valve. Possible to switch to different control modes and ramps through DIP switches. Model: G10 X: Standard high-pressure performance K: Kel-Cell version S: 316L pump head G: Vition/FKM Diaphragm and O-ring S: 316L valve seat F: 316L valves E: Elgiloy valve springs M: Kynar/PVDF valve spring retainer B: 10W30 motor oil 30,6 liter/min (1,8 m3/h) at 1450 RPM. 69 bar (1000 psi) at 1450 RPM and 103 bar (1500 psi) at 790 RPM. Pedpfxszv Ibfo Aphjgr Max inter pressure of 17 bar and 121 degree celcius maximum fluid temperature. Able to handle solid particles up to 500 microns (0,5 mm) It has a crack in the back left mounting foot (see picture)

Condition: good (used), Year of construction: 2015, functionality: fully functional, Reverse Osmosis Plant for ethylene glycol recovery, with a 12 m³ raw-water storage and homogenisation tank, nominal feed flow rate of 4 m³/h at 4 bar and filter backwash flow rate of 11 m³/h at 1.5 bar. Includes an automatic downflow multimedia filter with anthracite and sand beds supported on gravel, designed to remove suspended particles and protect the membranes. Compact skid-mounted reverse osmosis unit with two-stage filtration using replaceable 20- and 5-micron cartridges, a variable-speed high-pressure pump and a two-stage (1+1) × 6 reverse osmosis membrane configuration. Equipped with 8-inch DOW spiral-wound aromatic polyamide membranes installed in GRP pressure vessels rated up to 1,000 psi. Nominal recovery rate: 90%, equivalent to a theoretical permeate production of approximately 3.6 m³/h under design conditions. Low- and high-pressure piping and interconnections manufactured from AISI 316L stainless steel. Includes recirculation, front and side permeate collection, a CIP chemical cleaning system, membrane flushing, a GRP solution-preparation tank, a 25-micron mesh microfilter and a delivery pump for cleaning solutions and permeate water. Automated control system based on a Siemens S7-200 PLC, providing measurement and control of flow rates, temperature, pressures, pressure drops, operating times, pumping, backwashing, flushing and process alarms. Operator panel with a 6-inch colour touchscreen for parameter display and configuration, start/stop control, filter washing, alarm monitoring and trend graphs. Includes a 2 m³ reverse osmosis reject-water tank for subsequent transfer to the evaporator. Serial No.: MPP51525. Pedpfxezvddce Aphsgr

Year of construction: 2021, condition: excellent (used), functionality: fully functional, IKA MHD 2000/10 powder wetting and dispersing machine, capacity 2500 liters/hour, solids capacity max. 1300 liters/hour, rotor speed 4200 rpm at 50 Hz, 18.5 kW motor suitable for frequency converter 20-60 Hz, product temperature max. 135°C, operating pressure -1 to +16 bar, operating pressure double jacket max. 2.5 bar, liquid inlet DN 25, solid inlet DN 65, outlet DN 50, product contact parts stainless steel AISI 316L or AISI 316Ti9, frame and lantern piece stainless steel AISI 304, weight approx. 400 kg, used in the production of plant-based proteins (pilot plant) Pgjdpfxezu I Tfs Apher

Year of construction: 1995, condition: good (used), Radial fan from Venti Oelde with inlet silencer. !! Performance curve provided as an image attachment!! Volume flow: 46,308 m³/h Psdpfed Nqlcjx Aphogr Pressure increase: 4830 Pa / 48.3 mbar Weight: 2750 kg Temperature: 30°C Speed: 1480 rpm Fan efficiency: 82.9% Shaft power: 73.8 kW Motor power: 110 kW (90 kW also possible) Motor: VEM 315 S4 Voltage: 400 Volt / 50 Hz Year of manufacture: 1995

Condition: like new (used), Year of construction: 2020, functionality: fully functional, tank capacity: 50,000 l, usable tank capacity: 30,000 l, total height: 4,275 mm, inner diameter: 4,000 mm, outer diameter: 4,020 mm, overall weight: 4,250 kg, wall material: stainless steel, wall thickness: 10 mm, operating temperature: 100 °C, Equipment: CE marking, sanitary facilities, Brand new, never commissioned. Professionally decommissioned from an INEOS manufacturing facility prior to first use. Manufactured by Able Engineering, this high-specification sanitary 316L stainless steel pressure vessel is suitable for pharmaceutical, cosmetics, personal care, food, beverage and fine chemical applications. Designed for vacuum and low-pressure service and suitable for installation within ATEX-rated environments. Constructed entirely in 316L stainless steel throughout with 10mm shell and dish walls, dished top and bottom heads, heavy duty tubular stainless steel leg supports with bolt-down base plates, hygienic internal finish < 0.8 Ra, and full hygienic ferrule fittings throughout conforming to ASME BPE / BS3062. Suitable for CIP, excellent condition. Podpfx Apszhn Rqjhogr Material: 316L Stainless Steel throughout. Working Volume: 30,000 Litres. Shell ID: 4,000mm. Overall Height: 4,275mm. Shell & Dish Wall Thickness: 10mm. Design Pressure: -1.0 to +0.45 Bar.G. Design Temperature: -10°C to +100°C. Empty Weight: 4,250kg. Design Code: PD5500:2018, Cat.3. PED 2014/68/EU certified. Manufacturer: Able Engineering. Serial Number: PXL19785. Factory Tested: July 2021. Nozzles and fittings include 610mm hinged manway with grill, triple CIP sprayball arrangement, inlet connections, vent, pressure relief valve connection, Endress & Hauser hygienic thermowell, dual level switches, level measurement connection, lifting lugs, and earthing boss. Two units currently available, both brand new and never commissioned, sourced directly from the same INEOS facility. Tank saddles available on request for either single use or purchase. Please view our other listings for additional sizes and configurations — all stock is brand new, ex-INEOS, and available for immediate inspection and purchase. Original engineering drawings and full nameplate documentation available on request. Inspection welcome by appointment. Loading and transport can be arranged. Tracht Ltd specialise in hygienic process equipment for the food, beverage, cosmetics, pharmaceutical and chemical industries, with practical experience supporting both batch and continuous manufacturing environments. In addition to process vessels, Tracht Ltd supply and install stainless steel mixing vessels, Silverson high-shear mixers, hygienic lobe pumps, hygienic centrifugal pumps, access gantries, and provide full vessel installation and commissioning services. Whether replacing existing equipment or expanding production capacity, Tracht Ltd can specify, supply and install the right equipment for your application. Please contact us for further information or to discuss delivery and installation options.

Condition: used, functionality: fully functional, COMPLETE POWDER MIXING, WEIGHING & BAGGING PLANT – RUBERG / PAGLIERANI Complete industrial plant for mixing, weighing, conveying, and bagging of fine dry powders. The equipment is currently installed, FULLY OPERATIONAL, and available for inspection and demonstration in operation. The equipment is offered either AS A COMPLETE PACKAGE OR AS INDIVIDUAL MACHINES / SYSTEMS. The plant has been used for the processing and packaging of fine mineral powders. EQUIPMENT INCLUDED: RUBERG CM 2000 – 2,000 KG MIXING SYSTEM Manufacturer: Gebr. Ruberg GmbH & Co. KG, Germany Model: CM 2000 Batch capacity: approx. 2,000 kg Industrial batch mixer SEW main mixer drive: 37 kW Main mixer speed: 35 rpm 2 side rotor drives: 2 x 5.5 kW Side rotor speed: 720 rpm Georg Büttner weighing system Weighing range: 0–2,000 kg Resolution: 1 kg RUBERG bucket elevator Elevator capacity: approx. 17 t/h Available separately or as part of the complete plant. RUBERG CM-ZE 1000 2SR – 1,000 KG MIXING SYSTEM Manufacturer: Gebr. Ruberg GmbH & Co. KG, Germany Model: CM-ZE 1000 2SR Year of manufacture: 2001 Machine No.: 168 / 11013 Useful mixing volume: approx. 1,000 liters Total mixing chamber volume: approx. 1,300 liters Industrial batch mixer Main mixer drive: 15 kW Main mixer speed: 40 rpm 2 side rotor drives: 2 x 7.5 kW Side rotor speed: 1,455 rpm Georg Büttner weighing system Weighing range: 0–1,100 kg Resolution: 1 kg RUBERG bucket elevator Elevator capacity: approx. 10 t/h Pneumatically operated discharge system Discharge connection: DN 630 Filling connection: DN 175 Inspection connection: DN 150 Available separately or as part of the complete plant. PAGLIERANI TP35 WEIGHING & BAGGING MACHINE WITH ULTRASONIC SEALING Manufacturer: Paglierani S.r.l., Italy Model: TP35 Type: Weighing and bagging machine for valve sacks Number of filling spouts: 1 Application: Finely ground dry powders Main features: Single filling spout Horizontal-axis filling turbine Integrated weighing system Load cell Pgodpfx Apezv S Tlohsr Pneumatic bag support and clamping system Pneumatic product flow control Product feeding hopper Electrical control cabinet Pneumatic controls Conveyor arrangement Ultrasonic valve sack sealing system BRANSON ULTRASONIC SEALING UNIT Manufacturer: Branson Ultraschall / Emerson Technologies Model: Digital Compact 222 Serial No.: DAB 08102435 A The Paglierani TP35 is also available separately. CONDITION: Used – fully functional. All equipment is currently installed and can be inspected and demonstrated in operation by appointment. DOCUMENTATION: Technical documentation, operating manuals, and technical drawings are available for several components. Further photographs, documentation, and technical information are available upon request. SALE OPTIONS: The complete plant is offered as one package, but the individual RUBERG mixing systems and PAGLIERANI bagging system can also be purchased separately. Price for individual machines/systems: on request. Location: Greece Availability: Upon agreement Inspection and demonstration in operation: By appointment Dismantling, loading, and transport can be discussed separately.

Year of construction: 2003, condition: good (used), functionality: fully functional, X-TEK RTR160UF: X-TEK Systems Ltd., England Model: RTR160UF Type: Ultra Focus X-Ray System Max. X-ray voltage: 160 kV Max. power: 60 W Focus size: 5 (Ultra Focus) Manipulator: 50 kg, 5 axes Power supply: 230 VAC, 50/60 Hz Serial number: RTR/124 Model: RTR160UF X-ray source: 160 kV, 60 W, 5 m Ultra Focus Manipulator: 50 kg, 5-axis Serial No.: RTR/124 Supply: 230 VAC, 50/60 Hz Specified cabinet leakage: < 1.0 Sv/hr at any point on the cabinet surface under the stated test conditions. This is an industrial cabinet X-ray inspection system, designed for high-resolution non-destructive testing (NDT) of components, electronics, castings, solder joints, and similar items. The 5 m ultra-focus source is intended for very high-resolution imaging. Pgsdpfxezl Scrj Aphsr

Condition: used, Year of construction: 2016, Coolant cleaning system Manufacturer: Zyklomat Type: ZKR 14/350 Year of construction: 2016 For cleaning grinding emulsions Supply of max. approx. 250 L/min. at approx. 3.5 bar water Transfer to the filter system is carried out by the customer, air and foam-free. Temperature max.: 50°C Cleaning capacity: 350 L/min. Recirculation from clean tank to dirty tank: 100-350 L/min. Machine supply max.: 250 L/min. Filtration principle: ZYKLOMAT high-performance hydrocyclone Z1B-9/3 Separation particle size: approx. 5 µm Podpfx Aezwccmjphsgr Medium: Emulsion 3-6% Operating temperature: Ambient temperature Solid particles: approx. 5.14 m3 Operating volume max.: approx. 4.58 m3 Operating volume min.: approx. 3.60 m3 Process flow: Fully automatic full-flow filtration Sludge discharge: Fully automatic, with consistent consistency The dirty liquid is fed via customer-provided lift stations. The swarf and fine sludge produced during grinding (grinding debris, scale, corundum) are discharged via a scraper conveyor. In the upper scraper section, the sludge is pre-dried. Filtration takes place via ZYKLOMAT high-performance hydrocyclones. The system runs fully automatically. Maintenance: annual maintenance Availability: 10-2026 Double scraper tank for discharge of grinding sludge Type: KR 1.75-5.1 Total volume: approx. 5.14 m3 Volume max.: approx. 4.58 m3 Length: approx. 4,000 mm, including 70 mm stiffening Width: approx. 1,890 mm, including 140 mm stiffening Height: approx. 1,105 mm, including 100 mm base profile Neck height: approx. 2,300 mm Theoretical discharge volume max.: 15 kg/h Function: Coolant tank with integrated clean tank, sedimentation and flotation tank with fully automatic sludge discharge. 1 Bevel gear motor Voltage 400 V, 50 Hz, IP 54 as scraper drive 3 connection nozzles for return lines from three machines 1 clean liquid tank, integrated at the rear into the scraper tank. Oil-tight welded, with an internal, circumferential bevel gear, various cover plates (non-walkable plates screwed onto an angle frame), without ladder, without handrail, without internal rungs Volume max.: approx. 0.55 m3 25826

Condition: excellent (used), functionality: fully functional, Used Maguire plastic drying units are for sale. This listing includes a total of 13 units, with the option to purchase individual units or a larger package. Available are Low Pressure Dryer and Vacuum Batch Dryer / vertical dryer models. Condition as shown in the photos. Price depends on the selected unit and quantity. Pgedpfx Aszc D Ebsphsr These dryers are designed for drying plastic granules. The units are used, and their technical and visual condition corresponds to the photos. Additional photos of a specific dryer can be provided upon request. Available units: No. Designation Type / model as shown in the photos 1 D067 Maguire Low Pressure Dryer, model LPD2HE4 2 D049 Maguire Low Pressure Dryer, model LPD1HE4 3 D084 Maguire Low Pressure Dryer 4 D099 Maguire Low Pressure Dryer, model LPD1HE4 5 D054 Maguire Low Pressure Dryer, model LPD1HE4 6 D051 Maguire Low Pressure Dryer, model LPD1HE4 7 D065 Maguire Low Pressure Dryer, model LPD1HE4 8 D071 Maguire Low Pressure Dryer, model LPD1HE4 9 D068 Maguire Low Pressure Dryer, model LPD2HE4 10 D076 Maguire Vacuum Batch Dryer, model VBD-150 11 D081 Maguire Vacuum Batch Dryer, model VB-150 12 D089 Maguire Vacuum Batch Dryer, model VB-150 13 D091 Maguire Vacuum Batch Dryer, model VB-150

Condition: new, Year of construction: 2016, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, pressure: 6 bar, total height: 1,500 mm, total width: 700 mm, total length: 1,600 mm, Equipment: documentation/manual, For sale is a system that is still in its original packaging and located in the warehouse. The system has never been put into operation. Only the originally installed Grundfos pump was removed and replaced with a new replacement pump. Otherwise, the overall condition of the system corresponds to its original delivery condition. The system includes: Water softening system Pre-filter Ultrafiltration system with a downstream reverse osmosis system Activated carbon filter UV lamp All installed components and wear parts, such as filter cartridges, filter inserts, replacement UV lamp, etc., are included as spare parts. The system will be packaged and prepared for transport on four Euro pallets and one larger disposable pallet. The original purchase price was €47,788.47 net. Podpfxezbib Se Aphsgr Use of UF membranes for the filtration of viruses, bacteria, and cysts. Important minerals such as calcium and magnesium are retained after UF filtration and do not need to be added back using complex and expensive technology. - Health centers and dental practices, where people are exposed to particularly high risks of infection from waterborne pathogens. - Hotels and restaurants to provide high-quality and safe drinking water for consumption, food preparation, showering, and washing. - Legionella prevention in showers in public buildings. - Complete drinking water treatment in the household sector to improve drinking water quality for consumption, food preparation, showering, and washing. - Well water treatment

Condition: used, Year of construction: 2016, 1) Zyklomat coolant cleaning system, application: cleaning of grinding emulsion, cleaning capacity: 350l/min, recirculation clean tank-dirty tank: 100-350l/min, max. machine supply: 250l/min, supply pressure: 3.5bar, filtration principle: ZYKLOMAT high-performance hydrocyclone Z1B-9/3, separation limit: approx. 5µm, medium: emulsion 3-6%, max. medium temperature: 50°C, solid particles: brass particles, max. solids quantity: 15kg/h, total volume: 5.14m³, operating volume: 3.6-4.58m³, process: fully automatic full-flow filtration, sludge discharge: fully automatic, with non-flowing consistency, 2) double scraper tank for grinding sludge KR 1.75-5.1, total volume: 5.14m³, max. volume: 4.58m³, length: 4,000mm, including 70mm reinforcement, width: 1,890mm, including 140mm reinforcement, height: 1,105mm, including 100mm base profile, neck height: 2,300mm, max. theoretical discharge capacity: 15kg/h, function: coolant storage tank with integrated clean tank, sedimentation and flotation tank with fully automatic sludge discharge, serviced annually, fully functional, no known defects, with documentation. An on-site inspection is possible. Pgodpfx Aozvghksphjr

Condition: refurbished (used), Year of construction: 1997, functionality: fully functional, machine/vehicle number: 97 09 05 010 1/2, filter pressure: 15 bar, pressure: 15 bar, cake thickness: 25 mm, warranty duration: 12 months, year of last overhaul: 2026, operating pressure: 380 bar, number of chambers: 25, control voltage: 24 V, Equipment: documentation/manual, safety light barrier, Good day, We have two identical chamber filter presses in stock, which have been completely overhauled and are therefore in new condition. They are immediately available! Please see the attached photos: Chamber filter press – manufactured by MSE with plate thickness: 50mm each with an additional set of plates cake thickness: 25mm volume: approx. 210 l useful length approx. 1800mm (34 plates) format: 630x630 mm dimensions: 3700x1100x1800 mm (l x w x h) empty weight: 2700kg open filtrate discharge plate transport manual Podpfozt Nc Esx Aphsgr hydraulics electric Please let us know if you are interested in this press. We would be happy to send you a customized offer. Price on request.

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, Professionally designed crossflow ultrafiltration membrane system, engineered, built, and fully instrumented by a membrane specialist. 12 membrane modules in 3 parallel stages of 4 modules each, active membrane area 2.16 m². PVDF ultrafiltration membranes, separation limit 100 kDa, in PVC module tubes. Membrane stages can be individually shut off. Designed for diafiltration and pure concentration. Hygienic centrifugal pump, approximately 11 m³/h at approximately 2.5 bar feed pressure, crossflow up to 2.5 m/s. Retentate-side pressure adjustment via automatic proportional valve, stainless steel heat exchanger for temperature control. Ideally operated in conjunction with two feed tanks. Technical data: - Total membrane area: 2.16 m² (12 modules, 3 stages of 4) - Membrane type: PVDF-UF, separation limit 100 kDa; module tubes PVC, stages can be individually shut off - Circulation rate: approx. 11 m³/h at approx. 2.5 bar; crossflow up to 2.5 m/s - Permeate rate: 20–120 l/h·m² (depending on suspension/concentration) - Interfaces: Inlet/Outlet, each DN50 (DIN 11851) Pedpfx Apszmapvehegr - Instrumentation: Flow rate (feed/permeate), pressure and temperature sensors, proportional valve, stainless steel heat exchanger - Commissioned in June 2023; well-maintained, operational condition, regularly CIP-cleaned (last cleaning on 02/02/2026) More systems and equipment are continuously being offered for sale from a laboratory and pilot plant liquidation – inquiries are welcome. Sold on behalf of the client through the Köck auction house. Located in eastern Austria, exact address upon request. Collection/dismantling by the buyer.

Condition: used, Year of construction: 2007, Very little used Antares model AKER 630/50-OO chamber type filter press. - Manufacturer: Antares - Model: AKER 630/50-OO - Type of filter press: Chamber type - Dimensions of filter plates: 630 x 630 mm - Number and material of plates: (49) polypropylene chamber plates and (2) end plates - Number of chambers: 50 - Closing of filter press: Electrohydraulic - Hydraulik Vrchlabí model SHA-45, electric motor 1.5 kW - Removal of filter plates: Manual Pgjdjzvn Edepfx Aphjr - Filtrate discharge: Open delivery - Includes: local control panel (switchboard is not included)