Generator set

Doosan 417 KVA

Condition: used, Year of construction: 2021, Technical details: rated capacity: 220 kVA Number of working hours: 0 h type of fuel: Diesel revolutions per minute of the motor:: 1500 rpm output voltage: 400 / 50 Hz V weight of the machine ca.: 2,2 t dimensions L x W x H: 3,3 x 1,2 x 2,24 m The generator is soundproofed. - NEW -New Diesel engine: -6-cylinder -type P086TI -with battery 2x 12Volt 90 Ah Generator: -alternating current -400Volt / 50Hz -current 318 A -speed 1500 rpm -protection class IP23 -Isolation class H * Rsdpfxsu U E Edj Ag Nop

Condition: new, Year of construction: 2025, machine/vehicle number: 947526697, Frumecar ECA 500 fully mobile concrete batching plant production capacity: 30 m³/h * 4 aggregate hoppers * vertical axle mixer TRH-750 with a capacity of 750 liters * plant don't need any foundation and could be assembled in 1 day * 1 year guarantee from startup * ask for specific offer and technical details more machines and mixing plants on our website more information Rsdpfx Aehd I Sqsg Nsp Application: Building industry, Applicable material: Concrete, General

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Rjdpfx Aotvau Aog Njp Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: used, Year of construction: 2017, operating hours: 56,681 h, laser power: 4 W, 2017 Laser cutting machine with changing table and pipe cutting function. DURMA HD-FL 3015 BH / IPG 4kW – Manufacturer: DURMA – Model: HD-FL 3015 III BH-IPG 4kW – Year of manufacture: 2017 – Laser source: IPG – Control system: SIEMENS + CAD software + nesting software – Operating hours: 56,681 h Technical data: – Working area: 3000 x 1500 mm – Pipe cutting diameter: Ø 12 – 400 mm – Laser power: 4000 W (fiber laser) Maximum thickness parameters of cutting materials: – Black steel: up to 12 mm – Stainless steel: up to 10 mm – Aluminum: up to 10 mm – Copper: up to 4 mm – Brass: up to 6 mm Additional functions: – IPG fiber laser resonator – Water cooling system for laser source and cutting head – Extraction and filtration system under and above the laser – Double table system – Pipe laser with 4-point chuck and can cut up to 6 m – CAD software – Nesting software Rsdpfx Agsvyhcze Nsp – Pipe laser software – Very good condition, annual service performed 2024.12. If you have any more questions, we will be happy to answer.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Rjdpfsvf E Avsx Ag Nsp Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, Year of construction: 2014, pressing force: 122 t, overall weight: 40,000 kg, pressure: 315 bar, Machine has been used but is surplus and therefore for sale! Rjdpfjwa N U Dsx Ag Nsp

Condition: used, Year of construction: 2008, fuel type: diesel, motor manufacturer: TAD1640GE, Field of application: Construction Rsdpfx Agsvyn Ece Nsp Empty weight: 18.250 kg Generator capacity: 1.100 kVA Frequency: 50 Voltage: 400 Transport dimensions (LxWxH): 440x201x229 Please contact Sales Department for more information Over 80 years experience in maintenance. Expert that jointly reflects on the ideal solution for your situation. 1,000 hours or one-year guarantee: optimal reliability. Available 24/7. Quickservice. We can always supply a replacement generator. Wide range of stock that can be supplied immediately.

Condition: used, Year of construction: 2000, Power (KVA): 500 Redpfxox Sqd Dj Ag Nsp Working hours: 189

Condition: good (used), Year of construction: 1988, operating hours: 9,999 h, functionality: unexamined, overall weight: 3,500 kg, fuel type: diesel, color: blue, output voltage: 400 V, output frequency: 50 Hz, nominal power: 360 kW (489.46 HP), nominal power (apparent): 450 kVA, total length: 3,200 mm, total width: 1,340 mm, total height: 1,800 mm, rotational speed (max.): 1,500 rpm, type of cooling: water, Brand: Mercedes Benz - Stamford Model: 450 kVA diesel generator Year of manufacture: 1988 Serial number: On request Operating hours (read): Unknown Capacity (kVA): 450 Rjdpfxoydk Dge Ag Nop Capacity (kW): 360 Engine brand: Mercedes Benz Engine model: OM444A Fuel: Diesel Alternator brand: Stamford Alternator model: HC534C Voltage: 220 - 380 V Frequency (Hz): 50 RPM: 1500 Amperes (A): 684 Dimensions LxWxH (mm): 3200 x 1340 x 1800 Weight (kg) approx.: 3500 Units in stock: 1 Manufactured in: Germany Comments: Really good visual condition, operating hours unknown, twin turbo.

Condition: like new (used), Year of construction: 2012, operating hours: 500 h, functionality: fully functional, overall weight: 1,500 kg, fuel type: diesel, color: black, output current: 228 A, output voltage: 400 V, output frequency: 50 Hz, nominal power: 120 kW (163.15 HP), nominal power (apparent): 150 kVA, total length: 2,550 mm, total width: 1,110 mm, total height: 1,500 mm, rotational speed (max.): 1,500 rpm, motor manufacturer: John Deere, type of cooling: water, Brand: SDMO Model: J165 Year of manufacture: 2012 Serial number: On request Operating hours (indicated): Low hours Capacity (kVA): 150 - 174 (60Hz) Capacity (kW): 120 - 139 (60Hz) Engine brand: John Deere Engine model: 6068HF120 Fuel: Diesel Alternator brand: Leroy Somer Alternator model: LSA44.2M95J 6/4 Voltage: 230-400V Frequency (Hz): 50 - 60 RPM: 1500 - 1800 (60Hz) Amperes (A): 228 Dimensions LxWxH (mm): 2550 x 1110 x 1500 Weight (kg) approx.: 1500 Units in stock: 1 Made in: France Comments: Low hours, ex-emergency set, in good working condition. Rsdoydk D Tspfx Ag Nep