Chip extraction fan

EMK 15 kW / 2935 U/min

Condition: good (used), Year of construction: 1962, High speed radial drilling machine, radial drilling machine, drilling machine, boom drilling machine, high speed radial drilling machine -Clamping table: 400 x 1100 mm -Projection: 930 mm -Taper mount: MK4 -Engine power: 1.35/1.8 kW Ncedpfx Ajirax Uefljw -Speed: 41-1700 rpm -Columns: Ø 200 mm -Spindle stroke: 125 mm -Thread cutting device: YES -Feed: 0.075 - 0.3 mm/rev -Dimensions: 1800/1235/H2240 mm -Weight: 1500kg

Condition: new, plate thickness 0,8 mm throat 180 mm weight of the machine ca. 22 Kg dimensions of the machine ca. 500 x 450 x 160 mm Flanging machine is equipped with: Ncjdpfx Afjht R Hmolsw - Emergency switch - Footswitch - 7 pcs. Roll sets

Condition: used, Year of construction: 1997, Line 3 Stenner MHS9 machines from 1997 Ncedpow Nrhkjfx Aflow

Year of construction: 2026, condition: new, Magnetic separator for chip transport lines Pipe magnet with 4 magnetic plates (permanent magnet) Hinged door for easy removal of metal parts Pipe diameter: 180 mm Njdpfxocqvhxj Afljcw Available immediately Location: In stock at warehouse 54634 Bitburg

Condition: used, Year of construction: 2013, operating hours: 14 h, functionality: limited functionality, machine/vehicle number: TJ-350-20/40 KPSI //TJ-160-20/40 KPSI, total width: 1,500 mm, total length: 3,000 mm, total height: 2,500 mm, pressure: 2,800 bar, operating pressure: 2,800 bar, fuel: diesel, overall weight: 3,000 kg, rotational speed (min.): 700 rpm, rotational speed (max.): 1,500 rpm, high-pressure hose length: 60,000 mm, year of last overhaul: 2025, Equipment: rotational speed infinitely variable, A Bundle of 5 ea. UHP waterblast machines, c/w a vast variety of spares and accessories, as follows: 1 x High-Pressure Water Jet Unit with Deutz-MWM V-8 Diesel Engine adjustable pressure 0–1400 bar and 0–2800 bar, dump system, with plunger changeout kit as follows: 1400 bar at 99 liters/minute, and 2800 bar at 46 liters/minute. The fluid head of this pump, including stuffing boxes and valves will be used for both 1400 bar and 2800 bar. Changing pressure range between 1400 and 2800 Bar is carried out by a simple and easy plunger changeout. Njdpfx Afoxc E Trjlecw The unit was built in 2013 and kept operational as a backup machine, but was only used once for 14 hours at 2800 bar for a bundle heat exchanger cleaning project. This UHP machine is mounted on a zinc coated steel skid. The Deutz-MWM engine was purchased as a used engine, with approx. 3,000 operating hours , and was fitted in 2013 with a new Jetech UHDW high-pressure water jet pump. In addition, a large amount of accessories and spare parts are included, such as dump guns & foot valves, swivel joints, surface cleaners, rotary nozzles, high-pressure lances, nozzle inserts, seals, special tools, etc. An identical UHP waterblast unit is also available, but with a Scania V-8 engine and counting 850 operating hours at max. 1400 bar / 99 liters/minute. That unit is housed in a 20ft. container, with an 800 l Diesel Tank, a work bench /vise, Furthermore, there are 3 additional high-pressure water jet units with 110 kW power each, 2 of which have Volvo TD71A Diesel Motors, plunger changeout kits for 1400 and 2800 bar. A third unit is a Kamat K11000 with 2800 Bar OP. and a JCB Dieselmax engine. Also available is a hydraulic heat exchanger cleaning device with a rotating lance mounted on a scissor lift table, suitable for very large heat exchangers. All equipment comes from the closure of my company due to retirement. A buyer is sought for all machines and accessories as a complete package.

Year of construction: 2026, condition: new, The AL-KO Sanding table AST 1.5 BASIC is the entry-level model for the AL-KO sanding table program. It is certified according to GS-HO-11 and bears the seal "Wood dust tested according to BGI 739-1". It is therefore suitable for manual grinding as well as for machining workpieces with manual work machines. The grinding table is made of galvanized steel sheet. The workpiece support consists of a removable beech wood grate. It is accessible from all 4 sides. So that several people can work at the same time. Thanks to the sturdy, structurally stiffened construction, workpieces with a weight of up to 150 kg can be processed. In order to adjust the work surface of the AL-KO AST 1.5 BASIC to the required working height, it is equipped as standard with a mechanical height adjustment. The height adjustment is done without any tools by adjusting the feet in scaled grid dimensions. In addition, all feet can be adjusted in millimeters according to the respective ground conditions. The extraction trough is optimized in terms of flow technology. Due to the funnel-shaped design of the trough with integrated air duct, the air stream is directed to the intake socket. Depending on the extraction capacity required, the connection to the customer-specific extraction system can be made via a connection piece Ø 140 or Ø 160 mm. The bending of the machining surface on both two longitudinal sides also allows machining of workpieces on the end face The suction grilles are aligned with the flow connection to the suction port and thus guarantee an optimal extraction result. For cleaning work inside the sanding table, the slat grating can be lifted off and the air duct can be removed by loosening a few screws. The sanding table is delivered pre-assembled, only the feet have to be mounted and adjusted to the required working height. Tender specification AST 1.5 BASIC page 2 from 2 Technical data AST 1.5 BASIC: Ncjdpsfyadbefx Afljw - Intake socket 140/ 160 mm - Required suction performance 1.500 m³/h - Vacuum on socket at 22 m/s 1.000 Pa bei Ø 140 mm 700 Pa bei Ø 160 mm - Working height adjustable 735 – 1.015 mm - Working surface (W x L) 946 x 1.500 mm - Dimension (W x L) 1.000 x 1.600 mm - Weight approx. 73 kg

Year of construction: 2008, condition: ready for operation (used), A large-format single-shaft shredder Vecoplan is available. Rotor diameter: 370mm, effective rotor length: 1300mm, speed: 120rpm, knife rows: 37, knife dimensions X/Y: 40mm/40mm, feed opening X/Y: 1400mm/1300mm, hopper volume: approx. 3m³. Machine dimensions X/Y/Z: 3200mm/2400mm/1500mm, weight: approx. 5500kg. An on-site inspection is possible. Ncjdsyddyzjpfx Afljw

Condition: good (used), Year of construction: 1998, High-performance shredder with 1.2 m rotor width Large rotor diameter of 368 mm with 64 blades 37 kW motor Engine and gearbox replaced 6 years ago Ncedpfx Ajxwwvujflsw

Year of construction: 2026, condition: new, functionality: fully functional, power: 1,500 kW (2,039.43 HP), overall weight: 1,800 kg, table length: 2,500 mm, table width: 1,300 mm, Equipment: CE marking, documentation/manual, This laser metal cutting machine can operate sheet material with a thickness of 3-4 mm. Wattsan 1325 can cut stainless steel, carbon steel, galvanized steel, copper, aluminum, and titanium. It features a working space of 1300x2500 mm. The loading rollers of the precise Wattsan 13250 E make material feeding easier. The E-series laser metal machine has a maximum travel speed of 80 meters per minute. Laser power can be up to 1,5 kw. The bed here is made of steel. You can give our managers a call for additional details! Wattsan 1325 E characteristics Working area: 1300x2500 mm Laser power: up to 1500 W Weight: 1620 kg Virmer provides not only prime machines but also service and delivery. Our engineers and managers are ready to answer all of your questions and provide video assistance if required. Also, owners of Wattsan equipment get lifetime online support. Virmer is located in the Netherlands and works all over Europe. Virmer is Wattsan's official supplier. We provide not only laser engravers, but also metal cutters, welders, markers and cleaning machines. Wattsan is a Chinese manufacturer, which has been creating laser equipment for almost 15 years and keeps evolving with the help of its clients. Thanks to feedback Wattsan made over 50 modernizations, which made machines more reliable, precise and powerful so you could upgrade your business up to the new level. Njdpfjiicw Eex Aflocw YOU CAN WRITE OR CALL US! WE WILL SELECT THE RIGHT MACHINE FOR YOUR TASK On our company you can find a wide range of machines and components: Laser Metal Cutting Machine; Laser Metal Machine, Fiber Metal Laser, Fiber Metal Laser Engraver; CNC laser machine for metal; Laser machine for wood; CNC laser machine; Laser engraving machine; Laser engraver; Laser cutting machine for plywood; Laser engraver; Laser cutting machine for metal; CNC milling machine; laser marker. Lenses; Chillers; Cooling system for machine; Chiller S&A ; IPG laser, MAX photonics, Raycus; Compressor; Rotary device; Mirror for laser machine.

Year of construction: 1995, condition: excellent (used), 3 Sulzer MB 40-160/5 centrifugal pumps Flow rate: 32 m³/h Ncsdpfxjd Sybpj Aflsw Head: 147 m Maximum temperature: 130°C Seal: Mechanical seal with barrier fluid Drive power: Siemens 22 kW Speed: 2950 rpm ! Price per unit !