Punch nibbling machine

Ermak RPP 1270 x 30

Condition: good (used), Year of construction: 2009, operating hours: 899 h, machine/vehicle number: SN20090545, punching force: 30 t, sheet thickness (max.): 6 mm, table length: 2,000 mm, table width: 1,270 mm, overall weight: 11,000 kg, working range: 40 mm, ERMAK RPP 1270x30 Ton Punching Machine, Year 2009 Brand: Ermak Model: RPP 1270x30 Serial Number: SN20090545 Year: 2009 Main Features: Operating Hours: - POWER ON Hours: 899 hours - Punching Hours: 1 hour 6 minutes - Punching Force: 30 tons - Maximum Capacity: Crodpjv S Ufyefx Abzoc - Sheet Thickness: 6 mm - Sheet Dimensions: 1270 mm (width) x 2000 mm (length) - Travel: 40 mm - Axis Travels: - X-axis: 2000 mm - Y-axis: 1270 mm - Travel speed: - X-axis: 70 m/min. - Y-axis: 70 m/min. - C-axis speed: 100 rpm. - Strokes per minute: Up to 700. - Accuracy: - Positioning: ±0.03 mm - Position tolerance: ±0.1 mm - Numerical control (CNC): GE Fanuc 18i-PB - Oil capacity: 300 liters. - Power: 15 kW - Machine dimensions: - Length: 4250 mm. - Width: 4000 mm. - Height: 2330 mm. - Weight: 11,000 kg.

Condition: refurbished (used), Year of construction: 2024, Manufacturer: Elumatec Type SA/ SAS 142 Overhaul year: 2024 Saw blade max. carbide: 500 mm Drive power saw motor: 4 KW Saw motor speed: 2800 min-1 Cutting speed saw blade 500 mm: 4400 m/min Saw height control: infinitely variable, fully electronic Working range square 90° max.: 130 x 130 mm Working range flat: 90° max.: 190 x 130 mm Working range round: 90° max.:150 mm Pneumatic feed length: 5-560, 10-1120 mm Compressed air connection, on site 6 bar Weight(saw)approx.: 800 kg Dimensions LxWxH (saw)approx.:2900mm x 1400mm x 1500mm Installation area LxW: 2900mm x 1400mm Cjdpfx Abjuiy Nyjzsrc Additional description Elumatec SA/ SAS 142 4KW Retrofit Elumatec SA 142 4KW Retrofit Fully automatic sawing machine for non-ferrous metal and plastic After completion of the retrofit, the machine is in mint condition, both technically and visually. The machine will be overhauled in our company at the customer's request. Among other things, the following points were renewed: - Conversion to Siemens S7 PLC control - Conversion to Siemens HMI control panel - New electrical components - New pneumatic lines - Maintenance or replacement of all pneumatic cylinders and valve terminals - Maintenance of minimum lubrication system - Replacement of general wear parts - Overhaul of the cab Warranty: Unless otherwise agreed, we provide a 6-month warranty on all parts overhauled or replaced by us. Working time and wearing parts are excluded from the warranty. Optional: - Extension of the sawing area to flat 90° max.: 300 x 120 mm - Splitting extension (for a high-quality cut surface without return marks) - Servo-controlled material feed - Saw blade feed Servo-controlled - Mass clamping device Feed vice - Delivery and installation on your premises - Training of your employees

Year of construction: 1971, condition: good (used), decoiler - expansion mandrel with coil lifting table strip width: 1.200 mm Codpod Ha E Sefx Abzsrc strip thickness: 0,3 - 5 mm coil weight: 10 t mandrel Ø: 508 mm

Condition: used, Year of construction: 1980, machine/vehicle number: A-07/471A, sheet width - max.:130 mm straightening roll diameter:40 mm :5 :2+2 sheet thickness - min.:0,4 mm sheet thickness - max.:3,5 mm weight:0,4 t dimensions of the machine ca.:0,6x0,65x1,15 m with integrated, stepless adjustable Vari-drive, reversing, operating-mode switch for manual and automatic operation, introduction roller cage, position indicator of straightening rolls via analogue display, adjustment of straightening rollers via hand wheels, automatic swivel arm Csdpfx Aocxxx Rsbzsrc control, very good condition

Condition: used, Aufspannplatte - Tisch einer Langhobelmaschine - Tischbreite/Aufspannbreite: 1845 Tischlaenge/Aufspannlaenge: 5505 mm 7 T-Nuten laengs fuer T-Nutensteine: M 30 T-Nutenabstaende zueinander: 263 mm Gesamtlaenge: 6230 mm Plattenhoehe insgesamt: 350 mm Cjdpfx Aobn Amfebzsrc Gewicht: 11 t

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Credpfevf E Avsx Abzjc Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, Year of construction: 1990, I - beam section - flat steel 140 x 140 x 13 mm I-beam section - upend 120 x 120 x 13 mm L-beam 130 x 130 x 12 mm round bar steel 85 mm bending capacity - flat iron 125 25 mm flat steel 65 x 65 mm including various rollers: Pipe Ø: 219 mm (tool/roller Ø 535 mm) 140 mm (tool/roller Ø 420 mm) 273 mm (tool/roller Ø 520 mm) 203mm 168.3 mm (tool/roller Ø 500 mm) 75 mm (tool/roller Ø 400 mm) 49 mm (tool/roller Ø 420 mm) 48.3 mm (tool/roller Ø 420 mm) 22.5 mm (tool/roller Ø 420 mm) 32/32.5 mm (tool/roller Ø 420 mm) 60 mm (tool/roller Ø 420 mm) Cjdpfett Ecdex Abzorc

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, feed length X-axis: 500 mm, feed length Y-axis: 400 mm, feed length Z-axis: 400 mm, spindle speed (max.): 2,500 rpm, table length: 790 mm, table width: 460 mm, Table size 790 x 460 mm Longitudinal travel 500 mm Transverse travel 400 mm Vertical travel 400 mm Spindle travel 90 mm Spindle taper ISO 40 Spindle speeds 50 - 2,500 rpm Cjdswffymopfx Abzerc

Condition: like new (used), Year of construction: 2000, operating hours: 25,000 h, travel distance X-axis: 10,300 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 1,800 mm, feed rate X-axis: 10 m/min, feed rate Y-axis: 10 m/min, feed rate Z-axis: 10 m/min, position of the milling head: 2.5 x 2.5 °, spindle speed (max.): 3,000 rpm, spindle speed (min.): 60 rpm, table width: 3,300 mm, table length: 12,000 mm, mount diameter: 50 mm, total height: 48,750 mm, total width: 1,00,000 mm, total length: 2,12,000 mm, overall weight: 1,00,000 kg, Duplex milling are two machines located one opposite the other which can work seperately or as single machine, workpiece can be machined with 2 simultaneous spindles. Production increase of up to 50% in relation to conventional solutions, i.e. individual milling machines Improvements in part precision, by managing to do the machining of the part in one single setup, in most of the cases One sole operator can control the DUPLEX milling machines Reduced space and investment requirement comparing with two single machines Fast investment amortization due to the high productivity Duplex solution admits different configurations: single working area, pendulum working areas For machining excavator arms / boom like, CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo X-Axis: 10300mm Y-Axis: 2000mm Z-Axis: 1800mm Table Length: 12000mm Table Width: 3300mm Table load: 100000 Power on spindle: 22/30kW Spindle speeds: 60 - 3000Rpm Spindle Taper: 50ISO/Bt/Mk Feed rate X-Axis: 10000mm/min. Cedpfx Aborx Rxtezsrc Feed rate Y-Axis: 10000mm/min. Feed rate Z-Axis: 10000mm/min. Millinghead auto-index:2.5 x 2.5° Working hours: 25000H Length: 21200mm Width: 10000mm Height: 4875mm Weight: 100000kg

Condition: used, sheet width 250 mm coil outside dia. 1400 mm Codpfxsfn Aqme Abzerc weight max. in kg 2500 kg plate thickness 2 ... 4 mm straightening feed 2,5 ... 15 m/min coiler: expanding range mm total power requirement 1 + 4 kW weight of the machine ca. 1,8 t dimensions of the machine ca. m decoiler, MHR 250/4: max. coil diameter: 1400 mm coil diameter inside: 450 - 530 mm unbraked decoiler with pressure roller straightening machine, MR 250/4: Belt infeed height: 1250 mm The system was dismantled, checked and repainted.