Top and bottom belt sander

HESS Junior UP&DOWN 200 mm

Condition: like new (used), functionality: fully functional, Dowel inserting machine with operating gun for simultaneous glue application and dowel insertion Standard dowels Ø8 mm Dowels lenght 25 - 80 mm Nominal capacity 1 dowel/second (includes glue application) Fsdpfxjqu N U Ds Ap Depn Uses PVA adhesives (glue) in water dispersion viscosity 200-400mPa 1 pcs TANK FOR GLUE capacity 8 kg 1 pcs TANK FOR WATER capacity 8 kg Maximum pressure 5 bar

Condition: used, Year of construction: 1999, Equipment: all wheel drive, FAUN RTF 40-3 very good condition repainted in 2021 currently in use with us Trade-in possible under certain conditions / LFBK / Brillen Fzg. / AWU APU / VSN / eligible for GDV listing New general inspection (HU) Fsdpfx Apewpn Sao Depn New UVV inspection

Condition: new, Year of construction: 2026, Gannomat Concept 70 Eco Laminate – Body press with rapid traverse Technical data: Laminate body press from our showroom; Working area: width from 150 – 2,500 mm, height from 150 – 1,400 mm; depth 700 mm; - Laminate press beam at the top with 6 elements, laminate press beams on the side with 5 elements - Laminate press beams with proven tolerance compensation for tight body joints - Counterpressure surfaces are 40 mm thick, coated, continuous support plates - The pressing force of the press beams is continuously adjusted electronically via 2 potentiometers and set via a frequency converter, therefore, the torque transmission is absolutely wear-free. - Pressing force for horizontal press beams min. 500 daN (kg) to continuously max. 2200 daN (kg) - Pressing force for vertical press beams min. 300 daN (kg) to continuously max. 2200 daN (kg) - Including option: Fpedpfsiidm Nox Ap Don Rapid traverse speed for quick positioning of the press beams, controlled via automatic workpiece detection with sensors in the press beams, pressing speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Tapping mode for precise positioning of the two press beams, e.g. for low pressing forces, drawers and bodies at 45 degrees. Simple operation via 6 separate push buttons, freely adjustable preselection of pressing time with automatic opening, loading height 300 mm The machine is in our showroom and can be delivered immediately. Location: in stock at 54634 Bitburg - immediately available -

Condition: like new (used), Year of construction: 2017, operating hours: 20 h, functionality: fully functional, power: 55 kW (74.78 HP), Vecoplan Shredding Unit – Efficient Processing of Wood Waste The Vecoplan shredding unit is a powerful complete solution for the continuous processing of wood waste, cut-offs, strips, boards, and other wood residues into high-quality wood chips. The coordinated components ensure a consistent material flow, reliable continuous operation, and high economic efficiency. Components of the system: Vecoplan VTH 65/25/5/U Industrial Shredder (year of construction 2017) The VTH 65/25/5/U is a robust industrial shredder for continuous use in the wood industry. With its inlet opening of 650 × 250 mm and a drive power of 55 kW, it reliably and energy-efficiently processes a wide variety of wood residues. Depending on the material properties, the machine achieves a throughput of 1 to 5 tons per hour. The VTH series is characterized by high throughput rates, a robust design, and low maintenance requirements. Vecoplan VR 65/24 Vibrating Table Fpsdpjzh Ti Eefx Ap Dsn The vibrating table with a usable area of 650 × 2,500 mm ensures a uniform material distribution and continuous feeding of the shredder. This avoids peak loads, optimizes system performance, and ensures a smooth production process. Vecoplan KKF 500-1K-U Scraper Conveyor The downstream scraper conveyor with a conveying width of 500 mm reliably transports the shredded material for further processing or storage. It is ideal for transporting wood chips, sawdust, wood shavings, and pellets and impresses with its robust industrial design. Advantages of the system Complete, perfectly coordinated Vecoplan system Consistent material feed through vibrating table High throughput of up to 5 t/h Robust industrial design for continuous operation Low maintenance requirements Ideal for sawmills, wood processing companies, biomass plants, and pellet production Immediately ready for use for the economical processing of wood waste.

Condition: reconditioned (used), Number of spindles 5 St. Working width 230 mm Working height 120 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 5-30 m/min. Control Memory-Funktion Weinig Powermat 400 with HSK/Powerlock, axial/radial CNC controlled ----- Fpjdpsyy A Iqjfx Ap Don This machine is currently being refurbished at our facility! Pictures taken before dismantling and currently during the processing phase! Brief Summary: ----- - 5 spindles with 8,000 rpm - 4 x HSK/Powerlock - Axially and radial CNC adjustments of the spindles via control - CNC-controlled adjustment and positioning of the feed - Table tops with guide blades at spindles 2 and 3. - Includes Weinig/Neumann RF 15 return conveyor system Detailed Description: ----- Technical Data: Working width: 20-230 mm Working height: 8-120 mm 1st tool holder - bottom ----- Motor with brake: 5.5 kW Spindle diameter: 40 mm Speed: 6,000 rpm Tool swing diameter: 93 - 145 mm Axially travel: 5 mm Folding device MarathonCoatin for table insert in front of 1st lower Tool Holder 2nd Tool Holder - PowerLock - Right ----- Motor with brake: 7.5 kW Shared motor with left tool holder Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter 40 mm below table level: 93 - 200 mm Tool swing diameter 55 mm below table level: 93 - 180 mm Tool swing diameter for straight cutter heads max. 163 mm Max. tool diameter behind stop plane: 180 mm Max. groove depth: 35 mm Axially travel: 55 mm Spindle: CNC controlled axially Table tops with guide blades 3rd Tool Holder - PowerLock - Left ----- Motor with brake: Shared motor with the 2nd spindle Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter 40 mm below table level: 93 - 180 mm Table surface: 93 - 200 mm Tool swing diameter 55 mm below table surface: 93 - 180 mm Tool swing diameter for straight cutter heads max. 163 mm Max. groove depth: 35 mm Axially travel: 55 mm Spindle axially and radially CNC controlled Table tops with guide blades 4. Tool holder - PowerLock - top ----- Motor with brake: 7.5 kW Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter: 93 - 200 mm Tool swing diameter for straight cutter heads max.: 180 mm Max. groove depth: 35 mm Axially travel: 40 mm Split pressure shoe in front of upper tool holder, adjustable and pivoting away from the tool, spring-loaded. Pressure shoe in front of, and discharge after, the upper tool holder with electronic digital displays, integrated into memory functions CNC-controlled radial spindle 5. Tool holder - PowerLock - bottom ----- Motor with brake: 7.5 kW Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter: 93 - 200 mm Max. throat depth: 15 mm Axially travel: 35 mm Feed system ----- Frequency-controlled feed, infinitely variable with brake: 4 kW, 5 - 30 m/min Infeed roller in front of the first lower tool, pneumatically controlled up/down. Durofer pointed tooth rollers (Weinig patent) wi...

Condition: used, Year of construction: 1988, Distance between centres 1200 mm Fpjdpfxok Sat Do Ap Den Speed A) 70 - 380 U/min. turning speeds B) 380 - 2000 U/min weight 2,2 t +++++ Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. +++++

Condition: used, Year of construction: 1994, SECOND-HAND 5 SPINDLES MOULDER WEINIG MOD. PROFIMAT 23 - Working width 230 mm - Working height 120 mm. Composition : Fedperm Rxwjfx Ap Dspn - horizontal bottom - vertical right - vertical left - horizontal top - horizontal bottom Year 1994 V 380/50

Condition: reconditioned (used), Working width 3500 mm Working height 2550 mm Number of cylinders 6 St. loading dimensions L x W x H 4500x950x2900 mm Hess Speedy frame press ----- will be checked Insertion dimension / pressing length max. 3,500 mm Insertion dimension / pressing height max. 2,550 mm Sliding carriage for width adjustment locking in 50 mm Double hole grid system Electric height adjustment of the long-stroke cylinders (hydraulic) Insertion height of the abutment plates can be preselected in 4 positions 3 vertical printing cylinders stroke 1000 mm Pressure force per cylinder 2000 kN / 20000 N 3 horizontal printing cylinders stroke 80 mm Pressure force per cylinder 1250 kN / 12500 N Printing plate depth 100 mm width 140 mm Grid for cylinder fixation/rear bearing 50 mm Medium pressure beam with shut-off valve Final pressure switch-off and pressure control Control and pressing process in touch button operation Adjustable pressing pressure min. 25 – max. 160 bar Electrical connection 2.2 kW / 400V 3 pendulum pressure plates for studio windows 1 pendulum pressure plate for pointed windows 1 extension for pendulum pressure plate 1 small parts allowance Image and video not original, show identical model ----- Price of the above mentioned machine, upon request! ----- For your information: One image shows homemade counterprofiles. This image is for illustrative purposes only. The counterprofiles are not included with this frame press. ----- (technical data according to the manufacturer - no guarantee!) Fpedpoxnqw Tefx Ap Dsn

Condition: excellent (used), Year of construction: 1998, I sell the window production set: 1pc. tenoning profiling centre Weinig Unitec 10 1pc. profiling automat centre Weinig Univar 10 Year 1998. Moulding heads OERTLI. Fedpfjfzzhyox Ap Dspn Available immediately. Total price 17.000 euro. Condition very good !

Condition: used, Year of construction: 2019, operating hours: 500 h, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, Shredding/chipping machine Vecoplan VHZ 1300, hammer mills CPM, fan and cyclone filter JFK. The machine is in good condition and has only been in operation for approximately 500 hours. The line is complete with all conveyors. Fpodpfoympx Uox Ap Don