Edge banders Homag Edgeteq S 200 2018 Premilling

Homag

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Iajdpjyqybusfx Abcep Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Iajdpfx Aeyqx U Hobcjp Total connected load: 31 kW EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, power: 19 kW (25.83 HP), travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,730 mm, number of spindles: 20, number of tool stations in tool turret 1: 18, TECHNICAL DETAILS Iodpfeyttf Sex Abceap Working area X-axis: 4,175 mm Working area Y-axis: 1,730 mm Number of suction traverses: 8 Tool magazine positions: 18 Spindles Number of spindles for vertical drilling: 17 Number of spindles for horizontal drilling (X-direction): 2 Number of spindles for horizontal drilling (Y-direction): 1 Total number of spindles: 20 Milling unit Number of controlled axes: 4 Motor power: 18.5 kW Automatic tool changer Liquid-cooled MACHINE DETAILS Total installed power: 19 kW Control model: PC85 EQUIPMENT CE marking Front safety cover Note: Cones, milling cutters, and aggregates are not included in the scope of delivery. Safety fences are supplied based on availability (left side only). The machine is sold and delivered in its actual and legal condition (‘as seen and approved’), based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer is entitled to inspect the goods prior to collection, and assumes responsibility for installation, safety, and use of the machine at the destination. External reference: 6906

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,550 mm, workpiece height (max.): 40 mm, number of spindles: 30, travel speed (max.): 80,000 mm/min, TECHNICAL DETAILS Travel range X-axis: 4,175 mm Travel range Y-axis: 1,550 mm Travel speed X-axis: 80 m/min Travel speed Y-axis: 80 m/min Travel speed Z-axis: 30 m/min Maximum workpiece height: 40 mm Number of suction traverse beams: 8 Spindles Number of spindles for vertical drilling: 20 Number of spindles for horizontal drilling in X-direction: 10 Total number of spindles: 30 Milling unit Number of controlled axes: 4 + Flex5 Motor power: 15 kW Automatic tool changer Liquid-cooled Saw unit Tool magazine 1 Iedpsyttcwjfx Abceap Number of slots: 18 Tool magazine 2 Number of slots: 10 EQUIPMENT NC positioning of suction units Vacuum pump PowerControl P85 control system WoodWop 5.0 machine programming software Note: Cones and milling cutters are not included in the scope of delivery. The machine is sold and delivered in its actual and legal condition ("as seen and approved") on the basis of photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and is responsible for installation, securing, and usage of the machine at the destination. External reference: 7350

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Unit: Top Mill Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Iaedjytr Hbepfx Abcjp Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW EQUIPMENT Spray unit PowerControl PC22 machine programming software CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial data. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at the destination. External reference: 6216

Condition: excellent (used), FLEXIBLE C.N.C. WORKING CENTER 3 axes (X-Y-Z) Movable panel (workpiece), static working head - Horizontal position of the panel (workpiece) Iajdpfxjyu S I Ij Abcop Safety cabin (enclosure) of the working head Numerical Control PowerControl PC86 power Touch (Software woodWOP) Separate electric and command cabinet No. 2 Workpieces fixing clamps (for the panels introduction in the working area) WEEKE Prepositioning Unit - to position workpieces in machine with clamp grippers faster. In-feeding working table (panel support) and Out-feeding table (with motorized belts) Minimum workpieces dimensions (X - Y - Z) mm 200 x 70 x 8 (2 x 4 mm) Maximum workpiece dimensions (X -Y- Z) mm 3000 x 1000 (option mm 1300) x 80 (2 x 40 mm) Two panels simultaneously processables (in Z axe) Separate electric and command cabinet WORKING GROUPS (TOP): 2V42, 2H8X/2Y, N2 X-Y90,F2-ETP-6 KW No. 1 Vertical electro-spindle ETP-6 (power Kw 6) No. 1 Circular Grooving Saw (90° on X-Y axe) dia. mm 125 No. 42 Vertical drilling spindles (power Kw 2.3) No. 10 Horizontal drilling spindles (8 in X + 2 in Y) WORKING GROUPS (BOTTOM) 2V42, 2H8X/2Y, N2 X-Y90,F2-ETP-6 KW No. 1 Vertical electro-spindle ETP-6 (power Kw 6) No. 1 Circular Grooving Saw (90° on X-Y axe) dia. mm 125 No. 42 Vertical drilling spindles (power Kw 2.3) No. 10 Horizontal drilling spindles (8 in X + 2 in Y)

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, Specification: Cutting length: 4300mm Cutting Width: 4300mm Saw Blade Projection: 80mm Control Screen on Right Hand Side Machine Table fully air cushioned Program fence Speed forward 25m/min Program fence speed backward 90m/min Standard Clamps: 225, 325, 475, 775, 1075, 1825, 3425mm Power Concept – This allows several strips of different cross cutting lengths to be cut together with a performance increase of up to 40% Pressure beam height control Saw carriage speed 130m/min Main saw motor 11kw with pneumatic lift Scoring saw unit 1.5kw with pneumatic lift Electronic scoring saw adjustment from the control screen 4No air cushion tables 2160 x 650mm Label printer 400V 50Hz Control Touch touch screen monitor Data Transfer via network + USB port Iaodpoyuw Umefx Abcjp CE Eco Plus technologies save up to 20% on energy consumption

Condition: excellent (used), SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Edges thickness in strips / lippings (min/max) mm 0,4 / 20 Panels thickness (min/max) mm 8 / 60 NEW (in 2024) Numerical Control EDGETEQ MOD - Power Touch (WoodCommander) Adjustable Feeding speed up to 25 m/min In-feeding system EZ 14 Spraying unit (Anti-sticking liquid) In-feed fence, adjustable by N.C. Pre-milling Unit (vertical joint trimmers) 2 x Kw 3 Glueing Unit (P.U.R. Glue + Quick Melt system) Band Pressure zone, adjustable by N.C. Edge coils supporting unit (with No. 2 reels) Snipping (end-cutting) unit HL 84 (2 x Kw 0,5 ca.) Pneumatic swivelling and adjustment Rough Trimming unit BF 20 (2 x Kw 1,5 ca.) Multi Function Unit (Profile contour Trimming) FK 11 (2 x Kw 0,4 ca.) Profile edge scraping unit Finish processing unit (Glue scraper + Buffing unit) FA 11 Panels Return System "LIGMATECH" Mod. ZHR 541/L/095 (with Portal bridge and 360° rotating vacuum head) Ijdpfxeyt Izbs Abceap

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, power: 15 kW (20.39 HP), input voltage: 400 V, input frequency: 50 Hz, workpiece height (max.): 60 mm, edge thickness (max.): 3 mm, height adjustment type: electric, feed rate X-axis: 25 m/min, total length: 7,845 mm, year of last overhaul: 2025, Equipment: CE marking, documentation/manual, HOMAG Ambition 2260 Iaodpfxoyu S Iuo Abcop

Condition: like new (used), Year of construction: 2020, machine/vehicle number: 0-240-75-0703, input frequency: 50 Hz, type of input current: three-phase, NEW PRICE ONLY 85,000 EURO!!! Price valid only until April 20, 2026! Seize the opportunity! News update: The machine is reserved until April 15, 2026. If you are interested in purchasing, please leave a message and we will add you to the waiting list. We invite you to purchase a NEW, top-of-the-line panel saw: HOMAG SAW-TEC B-400 Pro Line, extended version for integration with automatic storage systems. The offered saw is BRAND NEW. It was purchased from HOMAG POLSKA Sp. z o.o. in 2020 and delivered directly to our facility by the manufacturer. The Homag service team started up the machine only; it has remained unused since then. Both the model and the Homag brand need no introduction in the industry, as Homag is recognized worldwide as a leader in the production of advanced, high-quality equipment. Our model is exceptionally well-equipped and features virtually all available options. A comparable saw in its standard configuration costs 100,000–110,000 EURO net (425,000–467,500 PLN net)*, while our extended version, adapted for automatic storage and with additional equipment, is worth around 190,000 EURO net (807,500 PLN net)*. Iasdpfx Aoyu Spxjbcep Advantages: - High throughput thanks to automated loading and extended saw blade movement. - Maximum efficiency with relatively compact space requirements. - Engineered for streamlined material flow and precise internal logistics. - Prepared for integration in networked production environments. We maintain direct contact and support with the manufacturer, HOMAG, for possible installation and commissioning at the buyer’s premises. In our opinion, the discount we offer—over 45% below the new machine price—makes this a highly attractive offer for anyone seeking a modern panel saw with automatic storage capability, or for buyers who might consider such an upgrade in the future; you could save approximately 90,000 EUR net (circa 400,000 PLN net)*. Of course, the saw can also operate independently, without connection to an automatic storage system. General terms regarding this sales offer: - The device is BRAND NEW, manufactured in 2020, so no warranty or guarantee is provided. - Returns are not accepted. - The price shown does not include VAT (23% for Polish buyers), which will be added to the invoice—please verify our price presentation. - Single owner. * 1 EUR = 4.25 PLN. Welcome to all buyers. We own numerous properties in Poland and are property developers building homes and apartments in Warsaw (the capital of Poland). The machines listed in our offers are our property. We acquired them as settlements from tenants in the furniture industry, so we know their history and condition, which match our descriptions. We remain in contact with manufacturers who can provide additional support—Homag, Otto Martin, OMC Machinery, and FANUM. As we do not need these machines, our prices are very attractive, especially given their near-new condition. We offer assistance with transport throughout Poland or the EU. Viewing by appointment is welcome before purchase.