Bale press

HSM HL 4809 LI

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. Ijdpjvwlqqofx Adwsal The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: not inspected (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 75,07,50,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8t Iodpoic Rl Dsfx Adwoal The hydraulic unit is functional, the drive motor is in the removed state.

Condition: like new (used), Year of construction: 2025, Portalkran 2x125 ton 30 Meter Hubhöhe Baujahr 2014 Iedegmdnfopfx Adweal

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Iaedsvgrh Uopfx Adwsl Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: good (used), Year of construction: 2009, functionality: fully functional, Weight 4950 kg, total weight 12000 kg 5.5 kW Iaodpfx Aswpmckodwel

Year of construction: 2004, condition: ready for operation (used), Connected load: 15.5kW, weight: 6.8t. Ijdpfx Aeip D Rzedwoal

Condition: ready for operation (used), DIXI 60SLD is a semi-automatic baling system with a pressing force of 60 tons, designed for economical volume reduction of recyclable residues in industrial and craft sectors: - Cardboard boxes - Foams - PET bottles - Insulation mats - and other pressable materials Horizontal baler, DIXI 60 SLD waste press with tipping device Technical specifications: Pressing force: 60 tons Specific pressure: 6.81 kg/cm² Power supply: 400V / 7.5kW Bale dimensions: 800 x 1100 x 1200 mm Number of ties: 3 Bale weight: approx. 370–410 kg Tying: manual Feed opening: 990 x 1110 mm Machine weight: 5,420 kg Average pressing cycle: 47 sec Year of manufacture: 2011–2016 Dixi 80SLD Baler Iodpfx Adera A E Ujwjal Technical Data of the Baler Brand: Dixi Model: 80 SLD Pressing force: 80 tons Drive power: 11 kW, 400 V / 32 A Feed opening (W x H): 1040 x 1110 mm Pressing cycle: approx. 35 sec Throughput: approx. 1,000 kg/h Bale size (W x H x L): 1120 x 1120 x 1200 mm Bale weight: depending on material, approx. 500–600 kg Bale tying: triple, manual Machine dimensions: Length: 4,200 mm (+cage 1,600 mm) Width: 1,830 mm Height: 2,620 mm Machine weight: approx. 8,000 kg Automatic bale ejection Robust construction for long-term use Year of manufacture: 2016–2020 Weight: approx. 8.4 tons Condition: Used

Year of construction: 2003, operating hours: 43,000 h, condition: repair required (used), machine/vehicle number: HBC 140 2x75kW 2003 (W230-005), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2003 Hardox bottom floor plate only Plastic valve Anti-rat cabling Hours 43.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Iajdpfx Aekcgynjdwsl Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Year of construction: 2022, condition: new, Two shaft Pre-shredder Cutting area: 2420x2000mm Special Cutting table, "Butterfly knives" developed by Metso First choice for: Iodpfx Ajfktqpjdweal Bagopening WITHOUT shredding the contents too much. The perfect bag opener for light packing material.

Condition: good (used), Year of construction: 1973, Waste compactor, waste compactor, compactor container, waste container, self-compacting container, mobile waste compactor, paper compactor container, paper container -Stationary press for: interchangeable containers -Load chute: covered -Pressing process: hydraulic -Pressing process: automatic -Emergency safety switch: at the deposit slot -Piston dimensions: 1450 x 650 mm -Piston stroke: 1100 mm -Transport dimensions: 2100 x 4500 mm -side threaded ratchets for skip containers Iedpfx Aob A Ii Sjdwoal -Functionally tested