Screw manufacturing machine

Ingramatic RP2

Year of construction: 1974, condition: refurbished (used), INGRAMATIC RP2 REVISED like NEW M8x90/45 mm. Fixed die length: 115 mm. Moving die length: 130 mm. Die height: 65 mm. 410 ppm Range production: M3 - M8 Completely revised as new. Machine visible in Calolziocorte (LC) - Italy REVIEW ACCORDING TO CE. The review includes: - DISASSEMBLY AND CLEANING OF EVERY PIECE - REPLACEMENT OF ALL BEARINGS - RECTIFICATION OF GUIDES OR POSSIBLE REPLACEMENT IF NOT SUITABLE - REVIEW OF THE INTRODUCER GROUP - OVERHAUL OF THE SLIDE GROUP WITH REPLACEMENT OF BRONZE PARTS - NEW LUBRICATION SYSTEM WITH CONTROL UNIT HYDRAULICS COMPLETE WITH PUMP, LEVEL SWITCH, PRESSURE SWITCH AND DISTRIBUTORS - NEW WATER PUMP - NEW CUP VIBRATOR COMPLETE WITH PANEL VIBRATOR AND PHOTOCELL CONTROL FOR TOO FULL - REVIEW OF THE ROLLER EVACUATION GROUP - PROTECTION CASE COMPLETE WITH LAMP AND MICRO - SOLENOID VALVE INSTALLATION WITH NEW AIR SYSTEM FOR VIBRATOR AND GUIDES - NEW ELECTRICAL SYSTEM ACCORDING TO CE STANDARDS WITH INVERTER - NEW ENGINE Dcsdpfx Asipm Riefzok - BELTS REPLACEMENT - RAL PAINTING INDICATED BY YOU

Condition: excellent (used), Year of construction: 2001, turning length: 8,000 mm, turning diameter over bed slide: 2,000 mm, workpiece weight (max.): 25,000 kg, turning diameter over top slide: 1,550 mm, Swing over bed Ø: 2000mm Swing over cross slide Ø:1550mm DBC Turning Length: 8000mm Spindle bore: 150mm Spindle power: 95kW Dcsdpfexxxbzjx Afzek Bed width: 1400mm Tailstock spindle Ø: 260Ø Stroke pinole: 200mm Spindle taper: Metric 80Mk Workpiece weight: 25000 Power: 95A Speeds / ranges: 360Rpm Feed rate X-Axis: 0 - 6000mm/min. Feed rate Z-Axis: 0 - 6000mm/min. Length: 16000mm Width: 5000mm Height: 3800mm Weight: 80000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1989, condition: excellent (used), Capacity (mm): M8x60/80 Djdjliqf Nspfx Afzsck Max Production: 300 ppm Year: 1989

Year of construction: 1988, condition: good (used), Carlo Salvi 1 die 2 blow Model 780/SV Maximum Cutoff dia.mm: 6,35 Dcodpfxshrdmxo Afzjk Max. Cutoff length mm: 97 Max. K.O. length (die side) mm: 80 Max. Speed, pcs, per minute: 360

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Dsdpfx Afjuz If Nozock Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: good (used), 1 used single-sided press Dcodpfx Aeul U Svefzsk Make: SACK & KIESSELBACH, year of construction: 1962,74 serial number 31900 Pressing force 630 t, stroke 310 mm Installation height 320 mm Working height 1200 mm Drive power 10 KW

Condition: excellent (used), Year of construction: 1972, functionality: fully functional, press force: max. 1.250 to. daylight: max. 480 mm width: 585 mm stroke: max. 355 mm weight: 9.000 Kg. Note: the press is been partly reconditioned by SACK & KIESSELBACH and the control system is been repalced. Dcodpfxjwuutbo Afzsk

Condition: used, Year of construction: 1981, National 2-3 Hot Former induction heater, feeder, straightener Dcsdpfswl Iw Usx Afzjk

Condition: refurbished (used), Year of construction: 2023, TRANSFER HEADERS SACMA SP22 2 DIE 2 BLOW Completely overhauled - Like new semi-tubular group installed Diam. 10x100 mm. Machinetype: 2 die – 2 blow transfer header Dcodspgw Ugspfx Afzsk Diameter range: 10 mm. Number of dies: 2 Number of stations (incl. cut off): 3 Cutting length: 110 mm. Shaft length under head: 100 mm. Output – pieces/min: 170

Condition: good (used), Max Diameter: M6 Max thread length: 42mm Djdpfx Aehtal Rsfzock Max length of rods: 75mm Year: 80's