BTS-MF60HD PET and Can Waste Baler

BTS-MF60HD PET-Dosen-Presse Can Crusher

Year of construction: 1994, condition: ready for operation (used), Motor power: 15.5kW/19.5kW, pressing force: 320kN, spec. pressure: 425kN/m², machine dimensions X/Y/Z: approx. 5700mm/1900mm/1800mm, weight: approx. 6000kg. The machine has a defect due to moisture and should be checked. Nedpfx Absip D Rpoysli

Condition: new, Year of construction: 2025, machine/vehicle number: 2022042210, Aluminum angled conveyor belt with substructure Conveyor belt length: 1,500mm flat + 3,000mm rising Pitch angle in bend 45°C Height of the horizontal top edge approx. 200mm PVC conveyor belt Conveyor belt EM 15/2 0+17 PVC green Belt width 500mm 31 pcs. T40 studs welded - pitch 300mm * antistatic due to threads in the fabric on the underside endlessly welded with stepped finger connection 40mm sidewall high-frequency welded on both sides * edge-free zone on both sides for tape guidance in the incline Lateral arrangement: -70+35-5+280-5+35+70 Nodpfsh Ellzsx Abyoli Full-surface underlay sheet Drive: Motor approx. 1.1KW Belt speed approx. 0.3m/sec * optionally controllable with frequency converter Connection 220/400V, 50Hz protection class IP54

Condition: refurbished (used), Year of construction: 2018, Mobile hammer mill Mobil Flex 1000 with drum magnet and discharge belt Drive: 250 Kw electric 4-hydraulic supports for lifting the machine for transportation Total weight: 33,000 kg Rotor weight: 3,000 kg Production: up to 11 to/h (depending on material size, grid size, parameter settings) With soundproof housing Dimensions: 11,750 x 2,500 x 4,380 mm Nlodpfx Abjph Uy Toysi Number of hammers: 24 pcs. Hammer weight: 22 kg System is being overhauled

Condition: used, machine/vehicle number: 12599, Rotor diameter: 600 mm Rotor width: 1450 mm 12-knife rotor 3 rows stator knives Nedpfok N Iy Nex Abyeli Inlet cross section approx. 780 x 1490 mm Drive motor: 132 kW

Condition: excellent (used), Here we offer you a Zwick / Roell tensile testing machine table-top testing machine.Zwick / Roell material testing machine BDO-FB0.5TH load in tensile / compression direction 500 N height 1565 mm , width 292 mm , depth 469 mmwidth of the test surface: infiniteTest range depth: 100 mmMax working stroke w.o. Accessories 1266 mmPC or printer interface RS 232Required PC connection (for PC operation) COM 1Performance data: 115/230 V (PH, N, PE)Rated power : 0.4 kVAN power frequency: 50/60 HzWeight: 47 kgType: BDO-FB0.5THCondition: used / usedScope supplied: (See picture)(Changes and errors in the technical data, details reserved!)We will be happy to answer any further questions you may have on the phone. Nljdpfsd Sr S Iox Abysi

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. Nlodpfx Asu Thhrjbyoi The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 1999, condition: used, Seocnd hand Entex Extruder PL- WE 100 complete with electrical cabinet. Wa in operation for Powder Coatings. Nljdpobqt Arofx Abyji For sell is also a Entex Extruder PL WE 70 ( Laboratory ). Photos on request.

Condition: ready for operation (used), Baler Hsm 155 VL Bale dimensions L x W x H: 1100 x 700 x 700 - 950 mm Bale weight: 2000 - 250 kg (Cardboard) Technical data: L x W x H: 1470 x 940 x 2259 / 2439 mm Weight: 950 kg Pressure force 16 tons Power supply: 400 V (three phases) Nedpfx Abora Nrmeyjli Motor power: 4 kW Bale ejector Hsm 155.1 VL baler pressure force 18 tons Price of Hsm 155.1 VL baler - 2600eur Hsm 155.2 vl baler pressure force 16 tons Price of hsm 155.2 vl baler - 2800eur

Year of construction: 2024, operating hours: 10 h, condition: like new (used), Extrusion Line with Densifier – Ideal for Recycling Applications Nedpfx Abotziudsysli This robust and versatile extrusion line is perfectly suited for recycling polyolefins such as LDPE, HDPE, and PP. Thanks to the integrated densifier, even materials with low bulk density – such as regrind, EPS, film scraps, and other lightweight plastic waste – can be processed efficiently. The densifier compacts the loose material and feeds it directly into the extruder, ensuring a consistent material flow and stable extrusion process even with challenging input materials. Key Features: • Suitable for all types of polyolefins • Ideal for lightweight, bulky materials like EPS or film regrind • Efficient feeding system via integrated densifier • Compact design and easy maintenance This line is an excellent choice for recyclers, plastic processors, and compounders who require flexibility and reliable performance when working with diverse input materials.

Condition: used, Coating system Hymmen CombiCoater ELX-S 1400 with UV dryer. * Technical data will follow shortly * For self-dismantling and collection. Nedpfx Abolf H Tceyoli