Sanding machine

MAWEG HILDEBRAND Saturn Duo

Condition: used, Year of construction: 2000, machine/vehicle number: 0-260-06-0228, Foot-operated 1200 x 800 mm 80 mm dust extraction port pneumatic connection Cable + plug, 16 A 1 set of operating tools 1 set of feeler rollers Rcedoigadlopfx Afhed

Condition: excellent (used), Year of construction: 2000, Refrigeration equipment Brand: Ers Type: SC 110. V/5 Power: 8 kW Year of manufacture: 2000 Rcodpfx Aed I Tlhjfhed

Condition: not inspected (used), Number of sanding units 4 St Rodpfxjt Tqy Ee Afhscd sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, System D8 brand painting chain, 94.50 linear meters, complete with towing, tracks and chain. Rcedjm D Hcfspfx Afhod

Condition: new, Product description: I-Beam Type Hanger Conveyors Conveyor Systems are one of the most important parts of the lines used in automatic coating plants. Our conveyor systems, which carries the parts to be painted in meters per day and kilometers per year, play an important role. Heavy parts to be coated are carried by webb conveyors which perform for long years with their long lasting bearings and steel cast chains. It has a wide carrying capacity range starting from 120 kg to 2 tons. • Operating principle of this type of conveyors is based on transferring suspended materials by chains and trolleys moving on a NPI profile by the help of a drive unit. • WEBB type conveyor chains are made of nodular cast iron or forged steel and subjected to heat treatment afterwards. • Special roller bearings used on trolleys are capable of operating at 200 °C. Greasers placed on trolley bodies provide lubrication for the system. Rcsdpfjdy Ewlox Afhod • The drive system can be built based on either the caterpillar system or the gearwheel system, with safety switches and moving trolleys. • Conveyor speed can be easily adjusted by use of a frequency controller. • Chain tensioning system consists of skids and springs. Rollers and support wheels are used for band turns.

Condition: ready for operation (used), Number of sanding units 2 st. sanding width 190 mm Sanding height max. 4-180 mm HESS - GLORIA 2 BELT SINGLE WOOD SANDING MACHINE ----- Manufacturer's description: ----- Compact design designed according to modern principles. Quiet and vibration-free operation thanks to rigid, stable machine housing and special insulation. Work safety device in accordance with the EC Machinery Directive with the "dust-tested" certificate. Offset grinding units with large-dimensioned tension rollers for good heat dissipation and stable sanding belt guidance. Sanding units with forced sanding belt oscillation. 2-point sanding dust extraction directly on the sanding roller. Airborne dust extraction on the large tension rollers. Integrated sanding belt blower for longer service life of the sanding belts. Integrated brushing and finishing device, adjustable via threaded spindle, with large dust extraction. Motorized grinding thickness adjustment of the entire upper unit via precision threaded spindles and linear ball sets on hardened and ground precision shafts with dust and dirt protection. Electronic digital display for Redev D Rg Djpfx Afhscd workpiece thickness (resolution 0.1 mm). Contact roller and grinding shoe in a balanced ratio to the grinding belt grain load. Hardened and ground grinding rollers. Maintenance-free and wear-free oxide ceramic grinding shoes (DBGM) with excellent sliding properties, good heat dissipation and high dimensional accuracy. Grinding belt tension via pneumatic cylinder. Grinding belt change via pneumatically controlled belt relaxation. Ability to adjust the grinding belt run when changing the belt. Electro-pneumatic pressure monitoring of the compressed air supply with visual fault display. Automatic machine stop triggered when sanding belt breaks and by run-in protection with integrated wood thickness control. Optical display on the control panel. Feed device and proven, calibrated non-slip and non-adhesive transport belts on precisely ground tables and spring-loaded pressure rollers. Cardan shaft drive for even wood transport. Feed speed continuously adjustable. Chip removal adjustment bottom via precision threaded spindle with dimension display via scale ring (resolution 0.1 mm) Ergonomic arrangement of the operating and setting elements on the machine front: sanding unit and brush device at the top, sanding unit and brush device at the bottom, workpiece transport device, sanding thickness setting, operating display, fault display. Control and operating unit with lockable main switch built into the machine housing. All motors electrically protected against overload. Technical data: ----- Grinding belt speed: 24 m/sec. Grinding width: 190 mm Grinding thickness: 4 - 180 mm Shortest workpiece length: 300 mm Feed speed: Continuously adjustable 5 - 25 m/min. Sanding belt dimensions: 200 mm wide 1600 mm long Electrical connection: 400 V, 3/N PE, 50 HZ Grinding units: 2 x 4 kW Feed: 0.75 kW Height adjustment: 0.18 kW Pneumatic connection: R 3/8", 80 NL, 8 bar Extraction air volume: 2 x 2000 - 2500 m3/h 20 - 25 m/sec. Extraction connection nozzle: 2 x 160 mm diameter at the top of the machine housing External dimensions: Length: 1600 mm Width: 1030 mm Height: 1820 mm Height with extraction nozzle: 1930 mm Working...

Condition: new, Cardan type conveyors are trolley models consisting of 4 bearing groups moving in a closed rail. These types of conveyors are indispensable on lines with their vibration-free movement, automatic lubrication feature and good appearance. Rcjdpedy Eytjfx Afhed Cardan type drive unit is overhead caterpillar type or lateral gearing torque safe. Pitches between the chain hangers are 400 mm and its multiples. Through central lubrication unit on the system, chain bearings automatically perform lubrication process as desired time interval. Torque limiter is used in order to protect the conveyor system when the drive units are compressed and forced. The bearings mounted on the chain are capable of operating at 250°C. The conveyor chain tensioning system can be performed as spring or screwed. The cardan conveyor rail is particularly bent from the sheet. In long-line conveyor systems, more than one drive unit is used and in such systems, a synchronous operation is provided between the drive units. There are three types as Light Type - Medium Type - Heavy Type based on the need. • Cardan type conveyor is based on moving the cardan chain in three axes on the cardan rail. • Cardan Type Drive unit as: Top caterpillar type or Side gear with torque safe system. • The pitches between chain hangers are 400 mm and its multiples. • Thanks to the central lubrication unit on the system, the chain bearings automatically lubricate at the desired time interval. • Torque limiter is used to protect the system from jamming and forcing of the drive units to protect the conveyor system. • The bearings mounted on the chain are capable of operating at 250 degrees. • Conveyor chain tensioning system is made with spring or screw. • Cardan conveyor rail is specially bent from sheet metal. • In long line conveyor systems, more than one drive unit is used, in such systems a synchronized operation is provided between the drive units. • There are three types according to the needs.

Condition: reconditioned (used), Year of construction: 1999, functionality: fully functional, machine/vehicle number: 1.790.230.010, Serial number: 1266 Operating pressure: 18 bar Rcedpoh U A A Ejfx Afhed Supply voltage: 220V, 2.0A

Year of construction: 2013, condition: used, Number of sanding units 4 st. sanding width max. 200 mm Rcjdpfoy Spvljx Afhod Sanding height max. 7-150 mm Working speed 8-16 m/min Band Speed 18-30 m/sec Stähle-Hess Sanding Machine Saturn-Duo ----- Manufacturer's Technical Description: Stähle-Hess Finish Sanding Machine, Model Saturn Duo Featuring 2 sanding units, plus additional upper and lower Roto-Finish sanding units. 1 Upper sanding belt 1 Lower sanding belt 2 Upper Roto-Finish sanding units 2 Lower Roto-Finish sanding units Workpiece Dimensions Height: 7–150 mm Width: max. 200 mm Minimum length: 300 mm Belt speed: 18–30 m/s (variable) Feed rate: 8–16 m/min (variable) ----- Price for the above-mentioned machine available upon request! ----- Note: This machine was previously used in conjunction with a Weinig Variomat four-sided planer/moulder (see Stock No. #7007). (Technical specifications provided by the manufacturer – subject to verification!) All listed prices are net, plus applicable statutory VAT.

Year of construction: 2000, condition: good (used), Number: 0107058 Cooling capacity: 1,100 W at +6° C Cooling capacity: 1,270 kcal/h at +6° C Rcjdpfx Afehri Ahohjd Maximum temperature: 44 °C Pressure: 25 bar Dimensions: 750 x 460 x 450 mm Weight: 80 kg