MG MG4R1520C

MG MG4R1520C

Condition: like new (used), Manufacturer: Varian Type: NHS-35 Condition: The pump is in very good condition and can also be supplied with a corner valve if required. Warranty: 3 months Delivery time: In stock Hodohmba Ajpfx Achsnr

Condition: new, functionality: fully functional, Year of construction: 2026, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Hnodpfx Ast Akt Rscher Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed performance: for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Variable geometry with linear guides for roller movement Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Condition: like new (used), Year of construction: 2024, Permanent overbelt magnet separator TYPE DMPM800 1,400 x 900 x 220mm ===== Solid steel construction, welded Construction welded & painted RAL 7016 (anthracite gray) Magnet dimensions: 800x500x180mm Drive roller + deflection roller S235 steel welded and machined Ø220x700mm crowned, shaft fixed with clamping bearings. Drive: GEMOTEG 1.1KW slip-on gear motor, speed 0.4-0.6m/sec Connection 400V, 50Hz, protection class IP54 Drive ready for connection to motor terminal box (commissioning must be carried out by a qualified electrician) PU conveyor belt DM 20/2 0+010 PU black matt 5.4mm thick Conveyor belt width: 650mm 7 TG-40 studs high frequency welded Belt material: 3-layer, particularly transversely stable * equipped with rust-proof alligator connectors RS125 Magnet properties: Hnedpfx Acshun Uishor Built-in magnetic core: Strontium Ferrite Y30 Bound SfRe strontium hard ferrite magnetic core encased in soft iron so that very high permeability can be guaranteed. Housing with 1.4301 stainless steel plate and pole shoes tightly closed and sealed. Conveyor belt, conveyor belt system, discharge belts, belt conveyor, magnetic separator, overbelt magnetic separator, recycling, wood chips, plastic, metal-free metal detection, neodymium, overbelt magnet, magnetic belt separator Our core competence lies in supplying the customer with exactly what he really needs. Together with our customers, we work out customer-specific, individual solutions and supply corresponding systems from our own production. Feel free to contact us by phone to find a suitable solution for your application.

Condition: refurbished (used), Year of construction: 2024, Overhauled: 2024 Control: SPS Siemens S7 Saw blade max: 500 mm motor power 4,0 KW Saw blade feed: 0-40 mm/ s continuously adjustable Saw height control electronic Working range square 90° max.: 130 x 130 mm Working range flat 90° max.: 190 x 130 mm Working range round 90° max.: 170 mm The machine has been completely overhauled in our company and is in mint condition. Among other things, the following points were renewed: Conversion to Siemens S7 PLC control Conversion to Siemens HMI user interface Conversion to pusher with servo control New electrical components New pneumatic lines New pneumatic components Conversion to valve terminal Optimization of the suction capacity New minimum lubrication system Replacement of general wear parts Overhaul of the cab The machine also has Minimum quantity lubrication Splitting extension (for a high-quality cutting surface without return marks) Pre-loading magazine for gentle handling of painted/anodized surfaces Offcut ejector in the pusher Foldable offcut tray Optional: Magazine width 3000mm Pusher length 6000mm Hedouiy Ngopfx Achsnr Pusher length 8000mm Reinforced motor 5.5 kW Mass clamping device for parallel sawing of several workpieces Online support connection Delivery and installation on your premises Training of your employees

Condition: excellent (used), Year of construction: 2004, machine/vehicle number: 0304/5599, functionality: fully functional, controller manufacturer: Delem, controller model: DA-65, working width: 3,000 mm, bending force (max.): 105 t, control type: CNC control, degree of automation: automatic, number of axes: 4, type of crowning: CNC-controlled, actuation type: hydraulic, Equipment: CE marking, documentation/manual, european tool clamping system, Crowning: Reflex - ACSG1 Hnsdpfxexv Eafj Acher Priključna moč: 11 kW Tools: Possible with agreement. NEW UPPER TOOL HOLDERS. Last service: 05/2025.

Condition: new, sheet width 2070 mm plate thickness 10 mm pre-bending 8 mm total power requirement 7 kW Hnjdpfevn U H Aex Acher weight of the machine ca. 5 t dimensions of the machine ca. 4050 x 1470 x 1550 mm

Condition: new, saw blade diameter 350 x Ø 30/40 mm cutting diameter 135 mm cutting length 430 mm dimensions of saw-blade 350x3,0/2,4x40 mm turning speeds 3800 U/min Dust suction hood 100 mm total power requirement 3,0 kW weight of the machine ca. 100 kg dimensions of the machine ca. 1300 x 800 x 1600 mm - Crosscut and miter saws for crosscuts - Miter adjustment on both sides (60° / 45°), with fixed stop - Compound cut on one side up to 45°, with fixed stop - Stable cast iron construction - Precise ball bearing guidance of the tool slide hardened and welded steel shafts - manual saw feed - Saw blade infinitely adjustable in height - socket for opt. suction Cutting data : - Cutting length at 90° = 430 mm - Cutting height at 90° = 135 mm - Cutting length at 45° = 310 mm - Cutting height at 45° = 92 mm Special accessories included: - 1x HM circular saw blade 350 x 3.0/2.4 x 40 mm Z = 108 FTZ neg. for aluminum and plastic - Hydraulic feed brake, continuously adjustable - Pneumatic material clamping from above consisting of: 2x vertical clamping cylinders, adjustable with hand levervalve - 1x machine stand Hnedpfxoxabqze Achjr - more powerful drive motor (3.0 kW)

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, controller manufacturer: Cybelec, controller model: Cybtouch 12, working width: 6,000 mm, bending force (max.): 300 t, control type: CNC control, number of axes: 4, Equipment: CE marking, emergency stop, european tool clamping system, safety light barrier, Used 6metre x 300ton Adira Cnc Press Brake - Hydraulic Pressbrake Hnedowu Ua Uopfx Achjr 300 Ton 6000mm bending Length Back gauge: X and Z Axis Upgraded touch screen control Cyblec CybTouch 12 Control System Year of Manufacture - 2005 Good service history including rebuilt ram cylinders, rebuilt crowning and upgraded control system Euro tool clamping

Condition: ready for operation (used), Year of construction: 2014, operating hours: 9,414 h, This BLM Adige LT8 4kW Co2 was manufactured in 2014. It features a Rofin DC035 3.5kw laser source and is equipped for tube cutting with a 3D cutting head. It handles materials up to 12mm thick and 206mm round, with lengths up to 6500mm. Consider the opportunity to buy this BLM Adige LT8 4kW Co2 tube cutting machine. Contact us for more information about this machine. Additional equipment • Bundleloader: 6.5 meters • Steploader: 6.5 meters • Output with Conveyor Belt: 6.5 meters at the front, 4.5 meters at the back Machine Benefits Technical Machine Benefits • Equipped with a 3d cutting head • Includes options such as weld detection, active focus, active scan, active piercing. Hedpex H A Rxjfx Achsnr • Laser source: rofin dc035 3. 5kw • Last maintenance: 24/6/2025 • Maximum weight: 35 kg/m • Maximum length: 6500mm • Maximum round diameter: 206mm • Maximum square: 200x200mm • Maximum thickness: 12mm Extra Information Machine still under power

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, turning length: 1,337 mm, turning diameter: 420 mm, General Control: Siemens 828 D Turning diameter: 420 mm Turning length: 1,337 mm Swing diameter: 700 mm Bar capacity: 89 mm Rapid traverse speed: 20 / 10 / 24 m/min Main spindle Bar capacity: 89 mm Chuck size: 305 mm Speed: 2,500 rpm Spindle power: 22 kW Spindle torque: 1,050 Nm Sub spindle Speed: 4,000 rpm Spindle power: 12 kW Spindle torque: 122 Nm Tool turret Technology: 12 stations Hodpfx Aex Ag Hmschsnr Tool drive: 5,000 rpm Power: 9.4 kW Torque: 90 Nm Tool holder: BMT-65 / BH Travel X: 280 mm Travel Y: 120 mm Travel Z: 1,390 mm Equipment Chip disposal: chip conveyor Coolant capacity: 240 liters Tool measurement: measuring arm in the working area Part discharge: parts catcher Bar feeder: prepared