CNC Machine Centres With Flat Tables

MORBIDELLI N100 22C

Condition: good (used), Year of construction: 2019, CNC through-feed center with dual clamp drive in X-direction and gantry design in Y-direction. The second gripper enables trimming down to 15 mm as well as continuous milling movement along the X-axis. The workpiece length is measured (X-direction) via sensor measurement. Working area: X-axis: 3,500 mm Y-axis: 950 mm Z-axis: 80 mm Milling spindle 12 kW HSK-F63, up to 24,000 rpm max. 4-position linear tool changer for milling tools. Max. tool diameter: 120 mm Max. tool length: 100 mm Single pick-up station for ergonomic insertion or removal of tools into the machine. Additionally usable as extra tool positions for up to 11 virtual tools. Automatic length measuring system for tools in Z-direction. Drilling head DH 25 8H 1S - 17 vertical spindles - 8 horizontal spindles - Grooving saw in X-direction Dowel insertion unit with 2 tools Dowel diameter: 8 mm, lengths: 20-25-30-35 or 40 mm Hnjdpjxrahcofx Airsk Air cushion tables at front and rear, foldable Machine software WOODFLASH with: - CNC Board (general machine operation) - Tool database (Tecno-Manager) - Programming editor External workstation license Dongle upgrade: 3D simulator with collision check for WOODFLASH at the machine Release of workpiece at the rear side of the machine Machine is supplied without tools and HSK holders

Condition: used, Year of construction: 2005, 2005 BIESSE ROVER B 4.40 FT 3-axis CNC machining center Technical features in the last photo Engine hours on: 45,343 Hodowmdynjpfx Airsnk Machine hours in automatic operation (work): 27,267

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Equipment and technical data: Cutting height: vertical 2,150 mm, horizontal 2,070 mm Cutting length: 5,300 mm Cutting depth: 80 mm Saw blade: diameter 303 mm, bore 30 mm, Z=60 alternate top bevel teeth Saw blade speed: 5,000 rpm Motor: 5.5 kW Required air pressure: 6 bar Measurement readout for: - horizontal cuts: via scale and strip cutting stop - vertical cuts: via scale from 0 - 1,300 mm Extraction port: 100 mm 5 material support rollers per meter of cutting length 1 infeed and 1 outfeed roller Pneumatic workpiece clamping device between the support rollers 1 central support element per meter of cutting length Twist-resistant, freestanding machine frame Pneumatically retracting slatted frame Round bar guide vertical and horizontal Fine-adjustable folding stop Fine adjustment for horizontal cuts via handwheel Strip cutting stop Manual programming rail with 5 T-nuts Pneumatic plunge of the saw unit Pneumatic saw head lock Control unit at the saw assembly: start button, stop button Operator panel with template holder Electronic digital display for the saw unit Electronic digital display for the folding stop Automatically swiveling saw head Hnedpfswka Ntsx Airok Location: Flörsheim Availability: short-term

Condition: used, Year of construction: 2014, CNC Machining Center Biesse skill 12 24 G FT Year of construction 2014 Machine no. 60961 Recording HSK F63 10x vertical drilling 12 switch positions Software: BiesseWorks X axis 2465 mm Y-axis 1260 mm Z axis 324 mm Disassembled for transport on normal trailer; 4500x2200x2400mm; Hodpfx Aswnhaneirenk Own weight 2000kg - Details: - └ Description: Pallet with white control box does not belong to this machine - Year: 2014 - Documentation available: Yes - CE certificate present: No - Serial number: 60961 - Number of milling spindles [pcs.]: 1 - Type milling table: Flat table - Tool clamping system: HSK-F63 - Drilling unit present: Yes - └ Vertical drilling spindles [pcs.]: 10 - Tool changer positions [pcs.]: 12 - System/software: BiesseWorks - Safety feature: Enclosed fence - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - Working range X [mm]: 2465 - Working range Y [mm]: 1260 - Z-axis working range [mm]: 324 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, SCM Morbidelli N100 CELL Hodjx Tgubopfx Airsnk Working area X: 4,286 mm Working area Y: 2,185 mm Working area Z: 150 mm Vertical drilling heads: 12 Horizontal drilling spindles X: 4 Horizontal drilling spindles Y: 2 1 grooving saw blade in X Tool changer: 20 positions Barcode reader 3 vacuum pumps SCM eye-M control system Good condition

Condition: used, machine/vehicle number: 008381, X axis working area: 4250 mm Y axis working area: 2280 mm Working Table: Flat table Main Electrospindle power: 12 KW Hodpfxjx Swc Hj Airsnk Number of controlled axes: 5 axes Total number of drilling spindles: 11 Total number of tool changer positions: 24

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Hnodpfjxy Tmnjx Airek

Condition: used, Year of construction: 2008, · Working area X-Y-Z: 3,660 x 1,550 x 130 mm · Travel length X-Y: 4,200 x 2,000 mm Description of the units and accessories (base) The structure of the base body is a monolithic construction made of thick-walled steel. It is stiffened by welded triangular plates across the entire machine bed, making it extremely stable. The triangular shape used for load-bearing parts, with a large base, is the secret to ensuring lasting precision and stability. The machine layout allows the user an optimal workflow despite minimal space requirements. The base body constructed in this way therefore offers the machining unit a balanced and secure base with particularly good load distribution. The mobile unit carrier in gantry design is made of a solid monoblock. It is positioned in the X direction on prismatically ground guides via recirculating ball slides. The work unit is mounted on this mobile unit carrier on prismatic, ground guides and a recirculating ball slide. Axis movement: The drive system in the Y and Z axes is provided by ground, high-precision recirculating ball screws. The X-axis is driven by a backlash-free, preloaded precision rack and pinion drive. This ensures balanced load distribution during the positioning process. This characteristic is important for ensuring balanced movement even in more complex tasks. The various axes are driven by brushless three-phase servo motors/brushless AC motors. These offer excellent positioning speeds thanks to very short ramp times. Furthermore, the measuring system is fully integrated into these motors. These properties make this type of drive completely maintenance-free. · Rapid traverse in X: 40 m/min · Rapid traverse in Y: 60 m/min · Rapid traverse in Z: 22.5 m/min Vacuum system (basic) · Vacuum pump: 100 cbm/h · Power: 2.5 kW · Max. negative pressure (connection) 0.9 bar Control / control cabinet · Office PC or industrial PC (see options) · Basic NC control: ESA-GV KVARA 6.0 · Cable remote control with the most important functions ELECTRIC/ELECTRONIC CNC CONTROL Universal is equipped with a powerful NC control. The integrated office PC gives the NC control an unparalleled level of familiarity: the software runs on Windows XP and allows quick and easy programming, which is easy to learn even for inexperienced users. The system is open and allows the connection of CD-ROM drives, audio cards, barcode readers, modems, printers, scanning systems, etc. Furthermore, the installation of all network systems, as well as all commercially available CAD programs, is possible. To reduce space, the control cabinet is located under the machine table, and the operator works at a separate terminal on casters, which can be freely positioned. XILOG PROGRAMMING SYSTEM Software features: - Import of DXF files - Import of ASCII files - User interface in the operator's native language (available for languages I - GB - F - D - E) - Linear and circular interpolation in three axes, linear in space, spiral in the selected plane - Assisted programming - Calculator for direct transfer of calculated data - Graphic and syntax aids for drilling and milling operations - Parametric programming to perform the same panel machining on different Hodsvvi Rfepfx Airsnk

Condition: used, Year of construction: 2014, Empty weight: 4.000 kg Price: On request Hnedpfexr Evlex Airek - Machine available from: 2026-01-26 - Year: 2014 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 89867 - Number of milling spindles [pcs.]: 1 - Type milling table: Flat table - Tool clamping system: HSK-F63 - Drilling unit present: Yes - Saw unit present: Yes - Tool changer positions [pcs.]: 12 - System/software: BiesseWorks - Safety feature: Safety mat - CNC options: Label machine, Loading system, Unloading system - Table length [mm]: 3600 - Table width [mm]: 1800 - Transport weight [kg]: 4000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: excellent (used), Year of construction: 2003, Year of manufacture: 2003 Voltage: 400 V Hnsdpfjtr A Evox Airok Frequency: 50 Hz Weight: 3200 kg Number of axles: 3